Aircraftspruce & Specialty Co. - NavirNet

More documents

Recommendations

Info

2006_121-128.qxd 6/23/06 12:53 PM Page 121 MIL-DTL 6000 OIL AND COOLANT HOSE Inside and out, Aeroduct MIL-DTL 6000 is designed to handle the effects of oil, alcohol, coolant, and water. The tube is oil resistant with a black cover reinforced with high strength mildew resistant yarns. It withstands extreme temperature conditions from -40°F to +250°F. Meets or exceeds U.S. military specs. Lightweight, flexible and easy-to-handle, making it the perfect hose for hard-to-get-to spots in tight engine compartments. Not recommended for fuel lines. Hose Dimensions Burst Wt./ Price I.D. O.D. Pressure Ft. Per Part No. (In.) (In.) (PSI) (Lb.) Ft. 6000-4 1/4 5/8 1,000 .14 $3.55 6000-5 5/16 11/16 1,000 .16 $3.80 6000-6 3/8 3/4 1,000 .18 $3.80 6000-8 1/2 7/8 1,000 .22 $3.95 6000-10 5/8 1 1,000 .26 $4.45 6000-12 3/4 1-1/8 1,000 .27 $5.50 6000-14 7/8 1-1/4 1,000 .32 $5.60 6000-16 1 1-3/8 1,000 .38 $5.90 MIL-H-6000 HOSE AVAILABLE IN 10 FT MAXIMUM LENGTHS AEROQUIP 306 HOSE (MIL-H-5593) A low-pressure hose for instrument air & vacuum lines. Consists of an inner tube of seamless synthetic rubber, reinforced with a single layer of cotton braid and a synthetic rubber cover. Used with slip-over hose fittings such as the AN840 series, or with Aeroquip 471 hose fittings when connecting to AN type fittings. Conforms to Specification MIL-H-5593. Specify hose I.D. when ordering. Hose Dimensions Burst Wt./ Price I.D. O.D. Pressure Ft. Per Part No. (In.) (In.) (PSI) (Lb.) Ft. 306-2 1/8 11/32 1,000 .056 $4.20 306-4 1/4 15/32 1,000 .072 $2.30 306-6 3/8 19/32 1,000 .096 $3.15 306-8 1/2 3/4 750 .144 $4.40 306-10 5/8 7/8 700 .168 $5.40 HOSE - HOSE FITTINGS AEROQUIP 471 HOSE FITTING Used with Aeroquip 306 Hose Aeroquip 471 hose fittings consist of an AN818 nut, an externally threaded 37° nipple and an internally threaded hose socket. All components are anodized aluminum. Fittings conform to MS27404. Tube Size AN818 Nut Part No. (In.)* Thread Size Price Ea. 471-2D 1/8" 5/6-24 $7.28 471-4D 1/4 7/16-20 $4.86 471-6D 3/8 9/16-18 $5.99 471-8D 1/2 3/4-16 $17.39 *Corresponds to tube O.D. of AN-type flared tube fittings. Not an Aeroquip dimension. AEROQUIP ASSEMBLY MANDRELS FOR AIRCRAFT HOSE ASSEMBLIES For use with Aeroquip 491 fittings. These tools are recommended to avoid damage to the sealing surface and to properly support the inner tube. Note: These are Aeroquip Factory Mandrels, which are highly recommended for best results. #491 #491 Hose Fitting Mandrel Hose Fitting Mandrel Size P/N P/N Price Size P/N P/N Price 3/16" 491-3 S-1051-3* $26.70 1/2" 491-8 S-1051-8 $30.80 1/4" 491-4 S-1051-4* $32.80 5/8" 491-10 S-1051-10 $34.40 5/16" 491-5 S-1051-5* $24.50 3/4" 491-12 S-1051-12 $34.60 3/8" 491-6 S-1051-6* $28.90 *With Removable mandrel. Aeroquip Qty. Discount: 15% for 20 ft.; 20% for 50 ft.; 25% for 100 ft. or more (Per Item) 121 AEROQUIP 303 HOSE This standard hose is used in med-pressure a/c hydraulic fuel, oil and coolant systems. An inner tube of seamless synthetic rubber is reinforced with a synthetic-impregnated single-wire braid over a single cotton braid and an outer cover of synthetic-impregnated oilresistant cotton braid. Operating temperature -65° to 250°F. Conforms to MILH-8794 (supersedes MIL-H-5511A). Used with Aeroquip 491 hose fittings. Hose For Max. Oper. Wt. per Price Part Tubing Hose Pressure** Ft. Per No.* Size I.D. (PSI) (Lb.) Ft. 303-3 3/16 1/8 3,000 .120 $4.35 303-4 1/4 3/16 3,000 .132 $4.65 303-5 5/16 1/4 3,000 .156 $5.30 303-6 3/8 5/16 2,000 .228 $5.70 303-8 1/2 13/32 2,000 .264 $6.00 303-10 5/8 1/2 1,750 .372 $7.10 303-12 3/4 5/8 1,500 .456 $7.20 * Corresponds to dash no. of Aeroquip 491 hose fittings. ** Safety factor of 4. AEROQUIP 601/AE701 HOSE An inner tube of seamless, specially formulated synthetic rubber reinforced with a stainless steel partial inner braid and full-coverage stainless steel outer braid. Operating temperature -40° to 300°F. Aeroquip 601 hose is widely used for aircraft fuel and oil lines where flexibility and light weight are prime considerations. Because of its lighter weight and lower operating pressure than type 303 hose, it is not recommended for hydraulic lines. Use with Aeroquip 816 hose fittings. Aeroquip 601/AE701 is a direct replacement for old 601 hose. AE701 hose has no shelf life and is the upgraded version of 601 hose. Hose For Max. Oper. Wt. per Price Part Tubing Hose Pressure** Ft. Per Part No.* Size I.D. (PSI) (Lb.) Ft. 601-4 1/4 7/32 1,000 .120 $11.60 601-6 3/8 11/32 1,000 .156 $9.80 601-8 1/2 7/16 1,000 .168 $11.80 601-10 5/8 11/16 1,000 .204 $13.70 * Corresponds to dash no. of Aeroquip 816 hose fittings. ** Safety factor of 4. AEROQUIP 666 HOSE Aeroquip 666 medium pressure Teflon hose is widely used in aircraft applications handling fuel, oils, and other fluids. It is unaffected by all fuels, oils, alcohols, coolants, or solvents commonly use in aircraft. Construction of Aeroquip 666 hose is of spiral extruded Teflon resin for the inner tube with a reinforcement and outer cover of Type 300 Series stainless steel wire braid. The result is a lightweight hose able to withstand prolonged flexing and vibration under all service conditions. Aeroquip 666 hose is also use in hydraulic and pneumatic applications at pressures up to 1500 psi. Hose Hose I.D. Hose O.D. Max. Oper. Wt. Per Price Part No. (inches) (inches) Pressure Ft. (lbs.) Per Ft. 666-4 .188 .312 1500 .08 $6.60 666-5 .250 .375 1500 .09 $7.10 666-6 .313 .466 1500 .11 $9.10 666-8 .406 .562 1500 .14 $11.90 666-10 .500 .656 1500 .19 $14.50 666-12 .625 .789 1000 .24 $15.90 REUSABLE 37° FITTINGS FOR #666 HOSE Use with Part Price Hose Size No. ea. 666-4 05-01320 $36.20 666-5 05-01321 $37.20 666-6 05-01322 $41.70 Part Aeroquip Price Number Hose Size ea. AE21502-E 666-4 $17.50 AE21502-F 666-5 $19.90 AE21502-G 666-6 $18.20 Use with Part Price Hose Size No. ea. 666-8 05-01323 $52.50 666-10 05-01324 $59.00 666-12 05-01325 $68.75 STRAIGHT CRIMP FLARELESS FITTINGS FOR #666 HOSE Part Aeroquip Price Number Hose Size ea. AE21502-H 666-8 $17.90 AE21502-J 666-10 $27.10 AE21502-K 666-12 $26.90 AIRCRAFT SPRUCE WEST AIRCRAFT SPRUCE EAST CORONA, CA • (877) 4-SPRUCE Prices Subject to Change Without Notice PEACHTREE CITY, GA • (877) 477-7823 CM WP ME HA AP LG EP CS IN EL AV TO PS BV BV
2006_121-128.qxd 6/23/06 12:53 PM Page 122 CM WP ME HA AP LG EP CS IN EL AV TO PS BV BV HOSE FITTINGS - ASSEMBLIES AEROQUIP 816 & 8891 HOSE FITTINGS Used with Aeroquip 601 Hose Aeroquip 816 straight hose fittings and 8891 90° hose fittings consist of a pre-assembled nut/nipple assembly and an internally threaded hose socket. The size 4 fitting has a cadmium plated steel nut and nipple. Sizes 6, 8 and 10 nuts and nipples, and all sizes of sockets, are anodized aluminum. Note: Aeroquip 816 fittings are not the same as AN816 fittings. Include the word “Aeroquip” with Part number when ordering. Aeroquip 816 Fittings Nut Aeroquip 8891 Fittings Price Thread Price Part No. Each Size* Size** Part No. Each 816-4 $15.30 1/4 7/16-20 8891-4 $38.80 816-6D $14.90 3/8 9/16-18 8891-6D $49.15 816-8D $17.95 1/2 3/4-16 8891-8D $60.50 816-10D $23.70 5/8 7/8-14 8891-10D $61.75 *Corresponds to tube O.D. of AN-type flared tube fittings. Not an Aeroquip dimension. ** Same thread size as AN818 nut of same dash no. Less 10%, 6 - 11 Aeroquip fittings; Less 15%, 12 - 24 Aeroquip fittings; Less 20%, 25 or more Aeroquip Fittings May be assorted sizes and types. AEROQUIP FIRE SLEEVE Aeroquip Firesleeve was specially developed to meet the fire resistance requirements of FAATSO - C53a OR TSO - C75. May be used for all fuel, oil, hydraulic, fire extinguisher & propeller feathering lines. "Fire-proof" hose lines as defined by FAA must withstand a direct flame for fifteen minutes under specified flow conditions without failure. “Fire-resistant” lines must withstand a 5-minute exposure under these conditions. “Fire-proof” hose lines are obtained when the proper size Aeroquip Firesleeve is selected from the chart below and properly assembled. 900591B Clamps - used to secure firesleeve material on each end over the basic hose assembly. See chart for correct size. P/N 900591B-1C ......................................$1.56 P/N 900591B-2C ......................................$1.76 P/N 900591B-3C ......................................$1.85 Use With 900591B Price Use With 900591B Price Hose # Clamp Per Hose # Clamp Per Part No. 303 601 Dash # Ft. Part No. 303 601 Dash # Ft. AE102-8 -3 -4 -1C $5.90 AE102-16 -10 -10 -3C $9.90 AE102-9 -4 -5 -2C $6.10 AE102-18 -12 - -3C $10.40 AE102-10 -5 - -2C $6.70 AE102-20 - -12 -3C $11.50 AE102-12 -6 -6 -2C $7.30 AE102-22 -16 -16 -3C $14.40 AE102-14 -8 -8 -2C $8.85 Quantity Discounts Same As Aeroquip Hose Firesleeve Clamp Installation Tool ..........P/N 05-00447 ..........$114.95 Economy Firesleeve Clamp Tool ............P/N 12-00684 ............$16.90 AEROQUIP AE466 INTEGRAL FIRESLEEVE TEFLON HOSE ASSEMBLIES These Teflon hose assemblies have brown or blue Silicone firesleeves extruded directly to the hose and the fitting, forming a tight smooth bond that meets fire test requirements TSO-C53A and TSO-C75 III and B. These hoses are non-age sensitive for long life, have excellent chafe resistance, are lightweight and have a smaller envelope for better hose flexibility. End fittings are stainless steal (MIL-H-25579) Hose conforms to Teflon MIL-H-27287. Available in brown or blue. Measurements are taken from sealing surface to sealing surface. Size Aeroquip P/N Base Price Blue & Brown Blue Add / Inch Brown Add / Inch -3 AE3663161BXXXX $31.50 1.53 1.20 -4 AE3663161EXXXX $24.00 1.71 1.33 -5 AE3663161FXXXX $35.50 -- 1.53 -6 AE3663161GXXXX $31.55 2.14 1.65 -8 AE3663161HXXXX $37.25 2.66 2.24 -10 AE3663161JXXXX $58.60 3.28 2.39 -12 AE3663161KXXXX $66.75 -- 2.71 122 AEROQUIP 491 HOSE FITTINGS Used with Aeroquip 303 Hose Aeroquip 491 hose fittings consist of an AN818 style nut, an externally threaded 37° nipple and an internally threaded hose socket. Fittings of sizes 3 through 6 have nuts and nipples of cadmium plated steel. Nuts and nipples for size 8 and larger are of anodized aluminum. Fittings conform to MS24587. *Corresponds to tube O.D. of AN-type flared tube fittings. Not an Aeroquip dimension. ** Same thread size as AN818 nut of same dash number. Tube Size AN818 Nut Price Part No. (In.)* Thread Size** Each 491-3 3/16 3/8-24 $8.38 491-4 1/4 7/16-20 $7.04 491-5 5/16 1/2-20 $8.29 491-6 3/8 9/16-18 $8.66 491-8D 1/2 3/4-16 $10.89 491-10D 5/8 1-1/16-12 $16.46 491-12D 3/4 1-1/16-12 $22.80 CUSTOM AEROQUIP 666 TEFLON HOSE ASSEMBLIES Aeroquip Teflon hose is constructed with a conductive, seamless smooth bore inner tube covered with a stainless steel braid. Unattracted by fuel, oil, coolants and solvents used in aircraft systems. Service and shelf life of Aeroquip Teflon hose is unlimited for all practical purposes. They can be used in fuel, hydraulic and pneumatic applications at working pressures to 1500psi. Minimum burst pressures are 8000 psi sizes -3 to -8. Temperature range is -65° to +450° F. Hose assemblies prices are straight to straight. Call for 45° and 90° elbow pricing. Measurements are taken from sealing surface to sealing surface. Size Aeroquip P/N Base Price Add/Inches Add/F.S. -3 AE3660000BXXXX $33.50 .53 1.21 -4 AE3660000EXXXX 25.95 .54 .56 -5 AE3660000FXXXX 37.50 .63 .57 -6 AE3660000GXXXX 35.50 .79 .70 -8 AE3660000HXXXX 41.25 1.03 .77 -10 AE3660000JXXXX 62.50 1.31 .84 -12 AE3660000KXXXX 70.55 1.55 .94 AEROQUIP MS28741 CUSTOM RUBBER HOSE ASSEMBLIES All hose assemblies are special-order and non-returnable. Custom-fabricated MS28741 hose assemblies fabricated (Aeroquip #303 or equivalent) from MIL-H-8794 hose and MS24587 fittings (Aeroquip #491 or equivalent). All assemblies proof tested in accordance with specification MIL-H-3795. Specify hose size and length of assembly in inches & eighths of an inch from sealing surface to sealing surface. Aeroquip P/N Base Price Add/Inches Add/F.S. 350-3-XXXX $24.35 .40 .56 350-4-XXXX 19.25 .43 .56 350-5-XXXX 27.65 .46 .64 350-6-XXXX 24.95 .50 .73 350-8-XXXX 32.60 .54 .85 Temp. range -65°F to +350°F. Color; Blue BLACK SILICONE FIRE JACKET This black silicone fire jacket has a temperature range of -65°F to +2000°F AND IS 5/8” I.D. Fits all E185–E225 & IO-470 breather tubes. P/N 05-00672 ..................$6.95 SILICONE HOSE ID OD Wt/Ft. Part Price (Lb.) No. / Ft 1/4” 0.45” .064 05-00659 $2.55 3/8” 0.67” .144 05-00660 $6.00 5/8” 0.82” .220 05-00661 $6.85 3/4” 1.07” .276 05-00671 $7.50 AIRCRAFT SPRUCE WEST AIRCRAFT SPRUCE EAST CORONA, CA • (877) 4-SPRUCE Prices Subject to Change Without Notice PEACHTREE CITY, GA • (877) 477-7823
Page 1: 2006_113-120.qxd 7/3/06 11:05 AM Pa
Page 5 and 6: 2006_121-128.qxd 6/23/06 12:53 PM P
Page 7 and 8: 2006_121-128.qxd 6/23/06 12:53 PM P
Page 9 and 10: 2006_121-128.qxd 6/23/06 12:53 PM P
Page 11 and 12: 2006_129-136.qxd 6/27/06 4:21 PM Pa
Page 13 and 14: 2006_129-136.qxd 6/27/06 4:21 PM Pa
Page 15 and 16: 2006_129-136.qxd 6/27/06 4:21 PM Pa
Page 17 and 18: 2006_129-136.qxd 6/27/06 4:21 PM Pa
Page 19 and 20: 2006_137-144.qxd 6/27/06 4:09 PM Pa
Page 21 and 22: 2006_137-144.qxd 6/27/06 4:09 PM Pa
Page 23 and 24: 2006_137-144.qxd 6/27/06 4:09 PM Pa
Page 25 and 26: 2006_137-144.qxd 6/27/06 4:09 PM Pa
Page 27 and 28: 2006_145-152.qxd 7/3/06 11:25 AM Pa
Page 29 and 30: 2006_145-152.qxd 7/3/06 11:25 AM Pa
Page 31 and 32: 2006_145-152.qxd 7/3/06 11:25 AM Pa
Page 33 and 34: 2006_145-152.qxd 7/3/06 11:25 AM Pa
Page 35 and 36: 2006_153-160.qxd 6/27/06 4:28 PM Pa
Page 37 and 38: 2006_153-160.qxd 6/27/06 4:28 PM Pa
Page 39 and 40: 2006_153-160.qxd 6/27/06 4:28 PM Pa
Page 41 and 42: 2006_153-160.qxd 7/3/06 12:12 PM Pa
Page 43 and 44: 2006_161-168.qxd 6/27/06 4:45 PM Pa
Page 45 and 46: 2006_161-168.qxd 6/27/06 4:45 PM Pa
Page 47 and 48: 2006_161-168.qxd 6/27/06 4:45 PM Pa
Page 49 and 50: 2006_161-168.qxd 7/3/06 12:25 PM Pa
Page 51 and 52: 2006_169-176.qxd 6/30/06 4:52 PM Pa
Page 53 and 54:
2006_169-176.qxd 6/30/06 4:52 PM Pa
Page 55 and 56:
2006_169-176.qxd 6/30/06 4:52 PM Pa
Page 57 and 58:
2006_169-176.qxd 6/30/06 4:52 PM Pa
Page 59 and 60:
2006_177-184.qxd 6/27/06 5:25 PM Pa
Page 61 and 62:
2006_177-184.qxd 7/3/06 1:13 PM Pag
Page 63 and 64:
2006_177-184.qxd 6/27/06 5:25 PM Pa
Page 65 and 66:
2006_177-184.qxd 6/27/06 5:25 PM Pa
Page 67 and 68:
2006_185-192.qxd 6/30/06 12:34 PM P
Page 69 and 70:
2006_185-192.qxd 6/30/06 12:34 PM P
Page 71 and 72:
2006_185-192.qxd 6/30/06 12:34 PM P
Page 73 and 74:
2006_185-192.qxd 6/30/06 12:35 PM P
Page 75 and 76:
2006_193-200.qxd 6/30/06 12:41 PM P
Page 77 and 78:
2006_193-200.qxd 6/30/06 12:41 PM P
Page 79 and 80:
2006_193-200.qxd 6/30/06 12:41 PM P
Page 81 and 82:
2006_193-200.qxd 6/30/06 12:41 PM P
Page 83 and 84:
2006_201-208.qxd 6/27/06 6:26 PM Pa
Page 85 and 86:
2006_201-208.qxd 6/27/06 6:26 PM Pa
Page 87 and 88:
2006_201-208.qxd 6/27/06 6:26 PM Pa
Page 89 and 90:
2006_201-208.qxd 6/27/06 6:26 PM Pa
Page 91 and 92:
2006_209-216.qxd 6/27/06 6:32 PM Pa
Page 93 and 94:
2006_209-216.qxd 6/27/06 6:32 PM Pa
Page 95 and 96:
2006_209-216.qxd 6/27/06 6:32 PM Pa
Page 97 and 98:
2006_209-216.qxd 6/27/06 6:32 PM Pa
Page 99 and 100:
2006_217-224.qxd 6/23/06 1:05 PM Pa
Page 101:
2006_217-224.qxd 6/23/06 1:05 PM Pa
show all

Aircraftspruce & Specialty Co. - NavirNet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?