Manual - Pine Tree Stove Shoppe

More documents

Recommendations

Info

144.1.1 CHIMNEY CONNECTIONYour chimney connector and chimney must have the same diameter as the appliance’s exhaust fl ue outlet. Theappliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge thickness. It is strictlyforbidden to use galvanized steel.A 6” diameter single wall chimney connector, used to connect the appliance to the chimney, must be installed withthe crimped end toward the appliance. This will ensure that the moisture which condenses from the burning woodwill flow back into the fire chamber. Each joint in the chimney connector must be secured with at least three sheetmetal screws.For installation of your chimney connector, the following recommendations may be useful.• The chimney connector must be short and straight. For optimum performance it is recommended thatall horizontal runs have a minimum 1/4” rise per foot, with the upper end of the section toward thechimney. For safe and proper operation of the appliance, see “INSTALLATION” instructions.• To insure a good draft, the total horizontal length of the connector should never exceed 8’ to 10’. Inthe case of vertical installation, the total length of the connector can be longer and connected withoutproblem to the chimney at the ceiling level.• There should never be more than two 90° elbows in the entire connector and chimney system. Neverstart with a 90° elbow. Always go up vertically for at least 2 feet from the fl ue collar before using a 90°elbow.• The connector must not pass through any combustible material, nor may it pass through a concealedspace (such as an attic, roof space, or closet). If passing through a wall, ceiling, or into a masonrychimney, use either chimney components listed for that specifi c use, or means acceptable to localauthorities having jurisdiction over the installation.This appliance must be connected to:A. A chimney complying with the requirements for TypeHT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliance,orB. A code-approved masonry chimney with a fl ue liner.Vent the stove into a masonry chimney or an approved,insulated solid-fuel stainless-steel chimneywith as short and straight a length of 6” diameterchimney connector as possible. Connection to a masonrychimney must be by a metal or masonry thimblecemented in place.TOWARDAPPLIANCEMALE END OFCONNECTOROR CHIMNEYPIPEFLUE GASDIRECTION58.1AW415-0762 / B / 11.12.10
154.1.2 ADDING SECTIONSAdd chimney sections, according to the manufacturers installation instructions. The chimney must extend atleast, 3 feet above its point of contact with the roof and at least 2 feet higher than any wall, roof, building orobstacle within 10 feet horizontally.LESS THAN10 FEET3 FTMIN2 FT MIN10 FT TONEARESTROOFLINERIDGE2 FTMIN3 FTMIN10 FT ORMORELESS THAN10 FT3 FTMIN3 FTMIN2 FTMINFLAT ROOFWALL59.1AW415-0762 / B / 11.12.10
Page 1 and 2: INSTALLER: LEAVE THIS MANUAL WITH T
Page 3 and 4: 31.0 INSTALLATION OVERVIEW1400PL IL
Page 5 and 6: 52.1 DIMENSIONSBCADE1400PL ILLUSTRA
Page 7 and 8: 2.4 GENERAL INFORMATION! WARNINGDO
Page 9 and 10: 93.0 PRE-INSTALLATION PREPARATION3.
Page 11 and 12: 113.6 MOBILE HOME! WARNINGDO NOT IN
Page 13: 4.1 CHIMNEY! WARNINGNEVER INSTALL A
Page 17 and 18: 174.1.4 TYPICAL THROUGH THE WALLIf
Page 19 and 20: 195.0 FINISHING5.1 LEG INSTALLATION
Page 21 and 22: 215.6 BRICKS AND BAFFLES INSTALLATI
Page 23 and 24: 237.0 OPERATION! WARNINGALWAYS OPER
Page 25 and 26: 257.3 LIGHTING A FIRE7.3.1 FLASH FI
Page 27 and 28: 278.3 RUNAWAY OR CHIMNEY FIREA CHIM
Page 29 and 30: 8.7 CARE OF GLASSIf the glass is no
Page 31 and 32: 9.0 REPLACEMENTSContact your dealer
Page 33 and 34: 3310.0 TROUBLE SHOOTING! WARNINGTUR
Page 35 and 36: 3512.0 SERVICE HISTORY43.1W415-0762

Manual - Pine Tree Stove Shoppe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?