Air Brakes and Train Handling Rules - Alaska Railroad
Air Brakes and Train Handling Rules - Alaska Railroad Air Brakes and Train Handling Rules - Alaska Railroad
68 EOT Telemetry DevicesReplace the battery in the EOT unit as follows:1. To unlock the EOT unit and remove the dead battery:a. Unlock the unit and swivel the handle down.b. Rotate the lock hasp off the battery latch and open bothlatches.c. Remove the latch hooks from the battery lid.d. Pull the battery out from the EOT enclosure.2. To install a new battery:a. Install a fully charged battery in the EOT battery enclosure.b. Align the connector on the battery with the round matingconnector at the bottom of the battery enclosure.c. Push the battery fully into the enclosure and latch the batterylid.3. To resecure the EOT unit:a. Rotate the lock hasp and the handle together.b. Lock the unit through the lock hole.68.3 TRAINLINK II Locomotive Cab UnitThe locomotive cab unit (LCU) is a self-contained telemetry transmitter/receiverwith the displays and controls the engineer uses tomonitor and operate the EOT unit.68.3.1 LCU Displays and ControlsThe LCU has the following displays and controls:A. Distance CounterThe distance counter measures the net distance (whether forward orin the reverse position) a locomotive travels.June 1, 1996 ARRC Air Brakes and Train Handling Manual 68-5
68 EOT Telemetry DevicesActivating the Distance Counter. To activate the distance counter:1. Press the CONTROL button (on the left side of the LCU frontpanel) one time, which then displays the distance the locomotivehas travelled in feet.NOTE: At first the distance increases whether the train istravelling forward or in the reverse position. However, if thetrain reverses direction, the distance counter begins decreasing.2. Press the CONTROL button a second time, which holds thedisplay at the net (forward or reverse) distance the locomotivetraveled. The display will flash.NOTE: If the distance count reaches its maximum value of± 19,999 feet, the count will freeze and the display will flash.3. Press the CONTROL button a third time, which resets and turnsoff the distance counter display.Calibrating the Distance Counter. To calibrate the distancecounter:1. Set the two-digit WHEEL DIAMETER switch (on the right sideof the LCU rear panel behind a small access door) by dialing thesecond and third digits (which represent wheel diameter) on theswitch. For example, for a 38.0-inch wheel, disregard the “3”and dial the “8” and “0” on the switch.NOTE: This two-digit switch accommodates wheel diametersfrom 35.0 to 44.9 inches.2. Check the wheel diameter setting as follows:a. Press and hold the DISPLAY TEST button on the LCU,which displays the wheel size setting on the DISTANCECOUNTER display. For example, a wheel size setting of38.0 inches would be displayed as “38.0.”NOTE: Charge units are also displayed in the PRES-SURE DISPLAY window.68-6 ARRC Air Brakes and Train Handling Manual June 1, 1996
- Page 105 and 106: 64 Train Handling2. If the equalizi
- Page 107 and 108: 64 Train HandlingEXCEPTION: If the
- Page 109 and 110: 66 Locomotive Equipment and Compone
- Page 111 and 112: 66 Locomotive Equipment and Compone
- Page 113 and 114: 66 Locomotive Equipment and Compone
- Page 115 and 116: 66 Locomotive Equipment and Compone
- Page 117 and 118: 66 Locomotive Equipment and Compone
- Page 119 and 120: 66 Locomotive Equipment and Compone
- Page 121 and 122: 67 Car Equipment and Components6 7
- Page 123 and 124: 67 Car Equipment and ComponentsThe
- Page 125 and 126: 67 Car Equipment and ComponentsA En
- Page 127 and 128: 67.8 Control Valve67 Car Equipment
- Page 129 and 130: 67 Car Equipment and ComponentsNOTE
- Page 131 and 132: 67 Car Equipment and ComponentsExha
- Page 133 and 134: 67 Car Equipment and Components67.1
- Page 135 and 136: 67 Car Equipment and Components67.1
- Page 137 and 138: 67 Car Equipment and Components67.1
- Page 139 and 140: 67 Car Equipment and ComponentsOn t
- Page 141 and 142: 67 Car Equipment and ComponentsMaxi
- Page 143 and 144: 67 Car Equipment and ComponentsD. T
- Page 145 and 146: 67 Car Equipment and ComponentsE. M
- Page 147 and 148: 67 Car Equipment and ComponentsEmpt
- Page 149 and 150: 67 Car Equipment and Components67.1
- Page 151 and 152: 67.17 Train Brake Releases67 Car Eq
- Page 153 and 154: 68 EOT Telemetry Devices— Distanc
- Page 155: 68 EOT Telemetry Devicesb. Make sur
- Page 159 and 160: 68 EOT Telemetry DevicesD. Battery
- Page 161 and 162: 68 EOT Telemetry DevicesThe RF NOCO
- Page 163 and 164: 68 EOT Telemetry Devices68.3.4 LCU
- Page 165 and 166: 68 EOT Telemetry DevicesA. Making a
- Page 167 and 168: 68 EOT Telemetry Devices68.7 Digita
- Page 169 and 170: 68 EOT Telemetry Devicesb. On older
- Page 171 and 172: 68 EOT Telemetry DevicesC. Checking
- Page 173 and 174: 68 EOT Telemetry Devices68.8 Digita
- Page 175 and 176: 68 EOT Telemetry Devices• A messa
- Page 177 and 178: 68 EOT Telemetry DevicesE. Odometer
- Page 179 and 180: 68 EOT Telemetry Devices68.8.4 Moti
- Page 181 and 182: 68 EOT Telemetry Devices68.8.6 Chec
- Page 183 and 184: 68 EOT Telemetry Devices• Operati
- Page 185 and 186: 68 EOT Telemetry Devices68.9 Digita
- Page 187 and 188: 68 EOT Telemetry DevicesEOT Unit Tr
- Page 189 and 190: 68 EOT Telemetry DevicesLCU Trouble
- Page 191 and 192: GlossaryAmp MeterThe instrument tha
- Page 193 and 194: GlossaryInverse Gradient: The tempo
- Page 195 and 196: GlossaryDrawbar ForcesThe longitudi
- Page 197 and 198: GlossaryHand BrakeAn assortment of
- Page 199 and 200: GlossaryLocomotive Cab Unit (LCU)A
- Page 201 and 202: GlossaryQuick ServiceThe local vent
- Page 203 and 204: GlossaryStretch BrakingSlowing or s
- Page 205 and 206: INDEXIndexAA-1 reduction relay valv
68 EOT Telemetry DevicesActivating the Distance Counter. To activate the distance counter:1. Press the CONTROL button (on the left side of the LCU frontpanel) one time, which then displays the distance the locomotivehas travelled in feet.NOTE: At first the distance increases whether the train istravelling forward or in the reverse position. However, if thetrain reverses direction, the distance counter begins decreasing.2. Press the CONTROL button a second time, which holds thedisplay at the net (forward or reverse) distance the locomotivetraveled. The display will flash.NOTE: If the distance count reaches its maximum value of± 19,999 feet, the count will freeze <strong>and</strong> the display will flash.3. Press the CONTROL button a third time, which resets <strong>and</strong> turnsoff the distance counter display.Calibrating the Distance Counter. To calibrate the distancecounter:1. Set the two-digit WHEEL DIAMETER switch (on the right sideof the LCU rear panel behind a small access door) by dialing thesecond <strong>and</strong> third digits (which represent wheel diameter) on theswitch. For example, for a 38.0-inch wheel, disregard the “3”<strong>and</strong> dial the “8” <strong>and</strong> “0” on the switch.NOTE: This two-digit switch accommodates wheel diametersfrom 35.0 to 44.9 inches.2. Check the wheel diameter setting as follows:a. Press <strong>and</strong> hold the DISPLAY TEST button on the LCU,which displays the wheel size setting on the DISTANCECOUNTER display. For example, a wheel size setting of38.0 inches would be displayed as “38.0.”NOTE: Charge units are also displayed in the PRES-SURE DISPLAY window.68-6 ARRC <strong>Air</strong> <strong>Brakes</strong> <strong>and</strong> <strong>Train</strong> H<strong>and</strong>ling Manual June 1, 1996