equipment sourcebook - Loctite.ph

LOCTITEHeading ® HYSOL 175 MANUAL APPLICATOR– Epoxy & Urethane AdhesivesItem Number: 98035The Loctite® Hysol 175 is an industrial grade, electrically heated, hand held, manual hot melt applicator. This unit comes with twoplug-in thermostats for either EVA or polyamide adhesives. The dispense quantity and timing are manually controlled with theergonomic trigger mechanism.Features:The complete source on Loctite® brand adhesives,• Includes two plug-in modules for dispensing bothsealants,polyamidelubricants,and EVAcoatings,hot meltsdispensing and curingequipment • Lightweight, available well balanced, only from and ergonomicallyHenkel Corporation.designed for operator comfort and application control• Completely enclosed heater housing for maximum safety• Fast heat up time for virtually immediate use• Advanced electronic controller provides power saving mode,when not in use for long periods of time• Fixed precision thermostat (plug-in module)for consistent heating• Thermal fuse protectionfor additional safetyTheory of OperationThe dispense rate andtiming are manuallycontrolled with thetrigger mechanism.TECHNICAL SPECIFICATIONSRequired Voltage110/120 VAC; 50/60 HzUtilities Power400 wattsNominal Stick Diameter1.75" Polyshot SticksSize2.67" W x 12.25" L x 9.63" HWeight2.65 lbs.Power Cord Length 10 feet (120")Maximum Extension Cord65 feetWarm-Up Time5 to 7 minutesDispense PowerManualDispense Melt Rate6.6 lbs./hourDispense Temperature 195°C or 215°CApplicator Adhesive Capacity0.125 lbs.Wire Cross-Section16 a.w.g. minimumHot Melt ChemistryEVA and polyamide hot melt sticksParts Included (1) Hysol 175 Applicator (1) Plug-In Module (215°C)(1) Plastic Stand (1) Standard Nozzle(1) Plug-In Module (195°C) (1) ManualAdditional Information For Hot Melt Nozzles and Accessories, see page 49.DISPENSING Hand Held HotMelt ApplicatorsURETHANE DISPENSERLOCTITE ® HYSOL REACTIVE URETHANE CARTRIDGE DISPENSERItem Number: 98011The Loctite® Hysol Reactive Urethane Cartridge Dispenser is used to dispense reactive polyurethane hot melts from 300 mlcartridges. This electrically heated, pneumatic dispenser includes a pressure-regulating stand with optional vertical applicationstand and foot switch for hands-free application. To minimizecartridge change-over times, the Loctite® Cartridge Pre-Heater(item 98012) is recommended.RequiredFeatures:UtilitiesVoltagePowerTECHNICAL SPECIFICATIONS120 VAC; 60 Hz; single phase400 watts• Lightweight, well balanced, and ergonomicallydesigned for operator comfort and application control• Low actuation force to reduce finger fatigue• Electronic temperature control• Rugged molded thermoset plastic housing for“cool to the touch” operation up to 250°F• Fixed precision temperature: 250°F (121°C)• Single cartridge loading• Direct nozzle cartridge mounting forquick cartridge changeover• Various nozzles for different dispense patternsTheory of OperationThis unit is used in the manualmode, where the operatormanually begins andterminates the pneumaticdispense cycle by a handtrigger. Flow control isachieved by adjusting theregulator supplied on thebase of the unit.Air Input80 psi air, filtered to 40 micronSize3.1" W x 12.5" L x 10.3" HWeight3 lbs.AdhesiveDispenses 300 cc aluminum cartridgeAir OutputMaximum 90 psiWarm-Up Time7 to 10 minutesDispense PowerAirDispense Melt Rate3.5 lbs./hourDispense Temperature 121°CApplicator AdhesiveCapacity0.125 lbs.Hot Melt ChemistryLoctite ® Hysol ® Reactive Urethane hot meltsParts Included(1) Hysol Reactive Urethane Cartridge Dispenser(1) Base with Regulator and Gauge (1) Wire Stand(1) 300 cc Cartridge Adapter (1) Nozzle with Cap(1) Heat Resistant Gloves (1) Cartridge Piercer(1) Tubing Assembly (1) ManualAdditional Information For Hot Melt Nozzles and Accessories, see page 49.Additional Accessories Sold Separately98012 – Loctite ® Cartridge Pre-HeaterFor additional information and the full line of equipment, visit www.equipment.loctite.com.47