equipment sourcebook - Loctite.ph

More documents

Recommendations

Info

Cure ConveyersLIGHT CURELOCTITE ® ZETA ® 7610 UV BENCHTOP CONVEYORItem Number: 98588The Loctite® ZETA® 7610 is a benchtop, ultraviolet curing conveyor used tocure light cure adhesives and coatings. This conveyor has a medium pressuremercury arc lamp which produces high-intensity ultraviolet energy in theUVA, UVB, and UVC spectral region. This system can be integrated into anautomatic or semi-automatic production line for cure-on-demand assembly.Features:• 6 inch, medium pressure mercury arc lamp• Lamp height can be adjusted to vary intensity• Variable bulb wattage: 150 or 300 watts per inch toaccommodate heat sensitive applications• Optimized to emit in the UVA, UVB, and UVC regions• Typical curing width 6 5 ⁄8" with 6" maximum part height• 1,000 hours of expected UV bulb life withproper handling and maintenance• Variable conveyor speed up to 56 feet per minute• Vacuum hold down for lightweight substratesTheory of OperationThe Loctite® ZETA® 7610 is a benchtop, ultraviolet curingconveyor used to cure light cure adhesives and coatings.This conveyor has a medium pressure mercury arc lamp whichproduces high-intensity ultraviolet energy in the UVA, UVB, andUVC spectral region. This system can be integrated into anautomatic or semi-automatic production line for cure-ondemandassembly.Gamma RaysThe Electromagnetic Spectrum10 4 100 1 1/100 10 -5 eVUVUVVisibleLight10 -2 10 -1 10 1 10 3 10 4 10 5 nmVisibleLightRadiationEnergyInfra-Red Microwaves RadiowavesWavelengthVUV UVC UVB UVA Blue Green Yellow Red100 200 300 400 500 600 700nmInput Power RequiredPower Consumption at300 W/in. SettingBeltMaximum Part Weight:Belt speed range(Minimum to Maximum)LampMaximum Part Cross SectionDimensionsWeightParts IncludedReplacement BulbTECHNICAL SPECIFICATIONS120 VAC; 1 phase; 50/60 Hz; fused for 21 ampsApproximately 2,200 watts304 stainless steel wire3 pounds1 to 20.0 inch/second60 to 1,200 inch/minute0 to 56 feet/minute1,800 watt Medium Pressure Mercury Arc Lamp6" H x 6.625" W31.6" H x 31.8" W x 23.8" D145 lbs.(1) Loctite ® ZETA ® 7610 UV Benchtop Conveyor(1) Ultraviolet Lamp(1) Ultraviolet Protection Glasses(1) Pair of Cotton Gloves (1) Manual98649 – Replacement 6" UV Bulb - 300 W/in.Additional Accessories Sold Separately98086 – Loctite ® ZETA ® 7011-ADosimeter-Radiometer116For additional information and the full line of equipment, visit www.equipment.loctite.com.
Light SourcesOur light sources and power supplies provide high intensity ultraviolet light for curinglight cure adhesives and coatings. These units are designed to be integrated into aLoctite® brand conveyor system, or used when the end user provides the conveyor andshielding requirements. Selection of a light source and power supply is based on thebulb type, electrical requirements, and the desired part movement.LIGHT CURE Light SourcesLOCTITE ® ELECTRODELESS LAMP ASSEMBLY AND POWER SUPPLYItem Numbers: 98004 – 208 VAC single phase, 10 amps, 50/60 HzItem Numbers: 98005 – 240 VAC single phase, 10 amps, 50/60 HzThe Loctite® Electrodeless Lamp Assembly comes equipped with a long life 6 inch “H” bulb. The lightsource is compatible with “D”, “V”, “H” and “H+” bulbs to tailor the spectral output of the light to theapplication. Selection of the 98004 or 98005 is based on the electrical capabilities available to the enduser. The Loctite® Electrodeless Lamp Assembly is typically used with the Loctite® ZETA® 7415 UVBenchtop Conveyor.Features:• Designed for use with the Loctite® ZETA® 7415 UV Benchtop Conveyor• Electrodeless bulb technology provides high intensity output• The system is shipped standard with an “H” bulb, but will accept “D”, “V” or“H+” bulbs to fine tune lamp spectral output• 5,000 hours of expected UV bulb life of the “H” bulb, with proper handling and maintenance• High UV output with low IR output results in less heat to the substrateTheory of OperationAn operator will assemble parts witha light curing adhesive or coating andmanually or automatically place thepart under the lamp for cure. Shieldingis obtained through the use of thisassembly with a Loctite® ZETA® 7415Benchtop Conveyor. If used elsewhere,shielding must be provided bythe customer.TECHNICAL SPECIFICATIONS20Spectral Output of “H” BulbPower Supply98004208 VAC single phase;18 amps; 50/60 Hz98005240 VAC single phase;18 amps; 50/60 HzLampFusion H Bulb - 300 W/in.Dimensions19.9" H x 6.6" W x 10.3" DParts Included(1) Fusion Lamp Assembly and Power Supply(1) ManualReplacement Bulb 983470 – Fusion H Bulb - 300 W/in.Additional Accessories Sold SeparatelyWatts per inch1612840200 250 300 350 400 450Wavelength in nm98086 – Loctite ®ZETA ® 7011-ADosimeter-Radiometer983471 –Fusion V Bulb - 300 W/in.983469 –Fusion D Bulb - 300 W/in.983470 –Fusion H Bulb - 300 W/in.For additional information and the full line of equipment, visit www.equipment.loctite.com.117
Page 1 and 2:
theequipmentsourcebook2007volume 6
Page 3 and 4:
Table of ContentsINTRODUCTIONEQUIPM
Page 6 and 7:
Equipment ServiceSolutionsINTRODUCT
Page 8 and 9:
Dispense SystemsDISPENSINGVOLUMETRI
Page 10 and 11:
DISPENSINGDispense SystemsLOCTITE
Page 12 and 13:
DISPENSINGDispense SystemsLoctite
Page 14 and 15:
DISPENSINGDispense SystemsLOCTITE
Page 16 and 17:
Dispense SystemsDISPENSINGTUBE BOND
Page 18 and 19:
Controllers &ReservoirsDISPENSINGMU
Page 20 and 21:
Controllers &ReservoirsDISPENSINGSI
Page 22 and 23:
Controllers &ReservoirsDISPENSINGRE
Page 24 and 25:
Controllers &ReservoirsDISPENSINGLO
Page 26 and 27:
DISPENSINGBOTTLE DISPENSINGLOCTITE
Page 28 and 29:
Hand HeldApplicatorsDISPENSINGLOCTI
Page 30 and 31:
Hand HeldApplicatorsDISPENSINGLOCTI
Page 32 and 33:
DISPENSINGTwo-Part VolumetricDispen
Page 34 and 35:
DISPENSINGTwo-Part Volumetric Dispe
Page 36 and 37:
Two-Part VolumetricDispensingMeter
Page 38 and 39:
Two-Part VolumetricDispensingMeter
Page 40 and 41:
DISPENSINGLoctite® DuraPump Select
Page 42 and 43:
DISPENSINGLoctite® Brand Meter Mix
Page 44 and 45:
DISPENSINGVariable Ratio Systems fo
Page 46 and 47:
DISPENSINGHand Held HotMelt Applica
Page 48 and 49:
DISPENSINGHand Held HotMelt Applica
Page 50 and 51:
Hand Held HotMelt ApplicatorsDISPEN
Page 52 and 53:
DISPENSINGBulk Hot Melt SystemsBulk
Page 54 and 55:
Bulk Hot MeltSystemsDISPENSINGLOCTI
Page 56 and 57:
Bulk Hot MeltSystemsDISPENSINGLOCTI
Page 58 and 59:
DISPENSINGLoctite® Brand Extrusion
Page 60 and 61:
DISPENSINGHand Held ValvesHand Held
Page 62 and 63:
Hand Held ValvesDISPENSINGGENERAL P
Page 64 and 65:
Hand Held ValvesDISPENSINGPINCH TUB
Page 66 and 67:
DISPENSINGValves & PumpsValves & Pu
Page 68 and 69: Valves & PumpsDISPENSINGLOCTITE ®
Page 70 and 71: DISPENSINGValves & PumpsGENERAL DUT
Page 72 and 73: Valves & PumpsDISPENSINGHIGH VISCOS
Page 74 and 75: DISPENSINGValves & PumpsPOSITIVE DI
Page 76 and 77: Valves & Pumps DISPENSINGLoctite®
Page 78 and 79: DISPENSINGPail PumpsLOCTITE ® HIGH
Page 80: DISPENSINGMonitoring SystemsMonitor
Page 83 and 84: Tapered Dispense Tips1 1 ⁄4" POLY
Page 85 and 86: Loctite® Brand Syringe Accessories
Page 87 and 88: AccessoryPARENT PRODUCTItem Numbers
Page 89 and 90: LOCTITE ® 200 BENCHTOP ROBOT STATI
Page 91 and 92: LOCTITE ® 400 BENCHTOP ROBOT STATI
Page 93 and 94: LOCTITEHeading ® S440 SERIES SCARA
Page 95 and 96: MOTIONCONTROLLOCTITE ® ADVANCING S
Page 97 and 98: Loctite® Brand Mounting Hardware,W
Page 99 and 100: O-Ring FabricationO-RINGFABRICATION
Page 101 and 102: LIGHT CURE SolutionsPRODUCTItemNumb
Page 103 and 104: LOCTITE ® 7700-HD LED LIGHT SOURCE
Page 105 and 106: Wand SystemsLoctite® ZETA® light
Page 107 and 108: LOCTITE ® ZETA ® 7735 UV WAND SYS
Page 109 and 110: LOCTITE ® ZETA ® 7760 UV WAND SYS
Page 111 and 112: LOCTITE ® ZETA ® 7401 UV CHAMBERI
Page 113 and 114: LIGHT CURE Cure Chambers &Flood Sys
Page 115 and 116: Light MetersDecreased radiant power
Page 117: Cure ConveyorsLoctite® brand cure
Page 121 and 122: Index119INDEXFor additional informa
Page 123 and 124: 121INDEXFor additional information
Page 125 and 126: 123INDEXFor additional information
Page 127: 125INDEXFor additional information
show all

equipment sourcebook - Loctite.ph

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?