equipment sourcebook - Loctite.ph

LOCTITE ® ZETA ® 7735 UV WAND SYSTEMSItem Numbers: 98317A and 958216The Loctite® ZETA® 7735 UV Wand Systems utilize a 50 watt mercury arc lamp with a universal power supply. The state-of-the-artlamp with elliptical reflector and custom coating delivers unequaled spectral and optical performance in the 50 watt category.These wand systems bridge the gap between low intensity and high intensity spot curing products. They are ideally suited for themedium to low intensity requirements of the photo-optics and audiology industries. Other common uses are fillet curing, wiretacking, and shallow potting. The system can be operated manually or in the timed mode and is capable of interfacing with a PLC.Continuous lamp intensity monitoring is also available by selecting item 958216 and the requiredLight Intensity Monitor item 891494. The light guides are also sold separately fromthe base units. Light guide choices are highlighted below.Features:• 5 to 7 W/cm 2 UV output• 50 watt high pressure mercury arc lamp• 2,000 hours of expected UV lamp life withproper handling and maintenance• Manual or timed shutter light exposure, 0 to 99.9 seconds• Hour meter for monitoring accumulated lamp life• Selector switch for either 110 or 230 VACAdditional Features for Item 958216 when used in conjunction with 891494• LED control display highlights relative intensitychanges in 10% increments• Minimum required intensity can be programmed for a warningor integrated to PLC for external alarm or shutdown conditionLIGHT CURE Wand SystemsTheory of OperationWhen the unit is switched on, the proper electrical power is immediately supplied to the lamp. It will take approximately fiveminutes for the lamp to reach full power. Once the lamp has reached full power, the unit is ready to cure adhesive. The operator willpresent the part under the end of the UV light guide. Curing will take place when the UV light is directed at the liquid adhesive.Engaging the foot switch opens the shutter and UV energy produced by the lamp is immediately transmitted through the flexiblelight guide. The end of the wand can be manually operated or mounted in a fixed position.Light Guides Sold SeparatelyDescriptions983677: Single end 5 mm diameter x 1,000 mm longLight Guide983684: Dual end 3 mm diameter x 1,000 mm longLight Guide (initial purchase requires951639 – Balancing Adapter)951681: Single end 5 mm diameter x 1,500 mm longLight GuideTypical Light Guide Cure Areas983677: 1 ⁄4" to 1 ⁄2" diameter983684: 1 ⁄8" to 1 ⁄4" diameter951681: 1 ⁄4" to 1 ⁄2" diameterLOCTITE ® LIGHT INTENSITY MONITORItem Number: 891494Power SupplyMain FuseDimensionsWeightParts IncludedTECHNICAL SPECIFICATIONS90/265 VAC; 50/60 Hz input1 A, 250 V5.5" H x 6.1" W x 6.8" D1 lbs.(1) Intensity Monitor(1) Sensor Input Cable(1) Power Cord (1) ManualTECHNICAL SPECIFICATIONSItem Numbers 98317A / 958216Power Supply100/240 VAC; 50/60 Hz inputPower Protection5 A / 250 V fuseAuxiliary Control Voltage12 VDCEntry Fuse3 A, 250 VDimensions7.3" H x 11.1" W x 12.8" DWeight19.5 lbs.Optimized Spectral Output RangeUVA, B, CReplacement Bulb(Item Number and Type)UV OutputCharacteristicsParts IncludedReplacement PartsTypicalUV Spectral RangePrimary Peak98339 – Lamp/Reflector Module50 watt HPMA UV Bulb5 to 7 W/cm 2(using 5 mm x 1,000 mm light guide)*250 to 410 nm365 nm(1) Loctite ® ZETA ® 7735 UV Wand System(1) Ultraviolet Protection Glasses (1) Line Cord(1) UV Lamp (1) Foot Pedal (1) Manual98339 – 50 watt HPMA UV BulbAdditional Accessories Sold Separately98048 –Loctite ® ZETA ®7021 Spot Radiometer(See page 114)891494 –Loctite ® LightIntensity Monitor –for 958216 only* Exact output measurement is dependent on the brand and calibration methodof the UV meter, and the condition and straightness of the light guide used.For additional information and the full line of equipment, visit www.equipment.loctite.com.105