Technical Manual 2005/06 - Tyrolia

More documents

Recommendations

Info

70 / SERVICE RELEASE/RETENTION ADJUSTMENT TABLE SKIER CODE kg/lbs cm/Ft’In” ≤250 251-270 271-290 291-310 311-330 ≥ 331 5 18 10-13 kg 22-29 lbs A 0,75 0,75 8 29 14-17 kg 30-38 lbs B 1,00 1,00 0,75 11 40 18-21 kg 39-47 lbs C 1,50 1,25 1,00 14 52 22-25 kg 48-56 lbs D 1,75 1,50 1,50 1,25 17 64 26-30 kg 57-66 lbs E 2,25 2,00 1,75 1,50 1,50 20 75 31-35 kg 67-78 lbs F 2,75 2,50 2,25 2,00 1,75 1,75 23 87 36-41 kg 79-91 lbs G 3,50 3,00 2,75 2,50 2,25 2,00 27 102 42-48 kg 92-107 lbs 49-57 kg 108-125 lbs 58-66 kg 126-147 lbs 67-78 kg 148-174 lbs 79-94 kg 175-209 lbs ≥ 95 kg ≥ 210 lbs How to use the Release/ Retention Adjustment Table: 1. Determine the Skier Code by locating the skier’s weight in the first column and the skier’s height in the second column. If the height and weight are not on the same line select the Skier Code closer to the top of the chart. 2. The Skier Code found in step 1 is for Type I skiers. For Type II skiers move down the chart toward the bottom one Skier Code. For Type III SINGLE CODE a-n o-s/B t/C-G H-L M-Q R-6 1 mm Mz Nm My Nm 2 3 4 5 6 ≤148 cm ≤ 4’10” H 3,50 3,00 3,00 2,75 2,50 31 120 149-157 cm 4’11”-5’1” I 4,50 4,00 3,50 3,50 3,00 37 141 158-166 cm 5’2”-5’5” J 5,50 5,00 4,50 4,00 3,50 43 165 167-178 cm 5’6”-5’10” K 6,50 6,00 5,50 5,00 4,50 50 194 179-194 cm 5’11”-6’4” L 7,50 7,00 6,50 6,00 5,50 58 229 ≥ 195 cm ≥ 6’5” M 8,50 8,00 7,00 6,50 67 271 N 10,00 9,50 8,50 8,00 78 320 O 11,50 11,00 10,00 9,50 91 380 105 452 118 540 Issued in accordance to ASTM and ISO 11088. Note: for proper adjustment, please look up the annual technical manuals of the binding manufacturer. Use calibrated ski bindings test equipment! skiers move down two Skier Codes. If the skier is age 50 or older or under 10 move up the chart one Skier Code toward the top. For skiers 13 kg/29 lbs and under, no further correction is required. 3. Find the column that corresponds to the skier’s boot sole measurement in millimeters. 4. The value where the Skier Code and the boot sole measurement intersect is the initial indicator setting for the skier.
If the intersection of the row and column falls in a blank box, do not move up or down the chart. Move sideways on the same row to the nearest box showing a visual indicator setting. 5. This value should be recorded on the workshop form under Initial Indicator Settings. Mechanical System Testing 1. Adjust the bindings toe and heel indicators to the Initial Indicator Setting. 2. Use a calibrated torque measuring device according to the instructions provided by the supplier. 3. Exercise that binding by release it at least once in all direction. 4. Three tests are required in each direction. The middle quantitative value of the three releases should be used as the test result. 5. Using the previously determined Skier Code slide across the chart to the column representing twist torque reference values. 6. If the test result is within one torque value above to one torque value below the reference value, it is in the Inspection Range. These results are acceptable and no further adjustment is necessary. 7. If the test result is within two torque values above to two torque values below the reference value, it is in the In-Use Range. The indicator value should be readjusted and the system retested so that it falls in the Inspection Range. Record the corrected indicator value in the box for final release/retention settings. 8. If the test result value falls out of the In-Use Range the system should be thoroughly inspected for the following: 1. Correct forward pressure 2. Correct Sole-hold down adjustment 3. Worn or contaminated AFD’s 4. Out of standard boot soles No work can be performed on the system until these problems are corrected. 9. Check the heel for forward lean the same way, determining the middle quantitative value of three vertical releases. Adjust if necessary. 10. Record final indicator settings on the workshop form in the area for final release/retention settings. SERVICE / 71 Type I Skiers • Cautious skiing on smooth slopes of gentle to moderate pitch. Skiers who designate themselves as Type I receive lower that average release/retention settings. This corresponds to an increased risk of inadvertent binding release in order to gain releasability in a fall. This type also applies to entry-level skiers uncertain of their classification. Type II Skiers • Skiers not classified as Type I or Type III. Skiers who designate themselves as Type II receive average release/retention settings appropriate for most recreational skiing. Type III Skiers • Fast skiing on slopes of moderate to steep pitch. Type III settings should not be used by skiers of less than 22 kg/48 lbs. Skiers who designate themselves as Type III receive higher than average release/retention settings. This corresponds to decreased releasability in a fall in order gain a decreased risk of inadvertent binding release. Note: If the skier reports release/retention problems see the chapter “trouble shooting release/ retention problems”, page 72 in the manual. Skiers who desire release/retention settings lower than Type I may designate themselves (I-). Type I- is inappropriate for skiers 17 kg/38 lbs or less. Type I- Move up the table one skier code. Skiers who desire release/retention settings higher than Type III may designate themselves (III+). Type III+ -Move down the table three skier codes. Skiers may select skier type designations that are different for twist and forward lean. In such a case, the selection shall be indicated by a slash separating twist and forward lean selections, in that order ( for example, K/L, K for the toe and L for the heel.
Page 1 and 2:
Technical Manual 2005/06 www.tyroli
Page 3 and 4:
Ski bindings 2005/2006 Active safet
Page 5 and 6:
Faster adjustment to any boot sole
Page 7 and 8:
Double FREE FLEX Double FREE FLEX I
Page 9 and 10:
Gliding on rails Mounting without d
Page 11 and 12:
03 04 DIAGONAL Toe Active protectio
Page 13 and 14:
Super Light - the lightweight Now a
Page 15 and 16:
RETAIL / 13 PARTS-REFERENCE CHART R
Page 17 and 18:
RENTAL / 15 PARTS-REFERENCE CHART R
Page 19 and 20:
NEW TEMPLATES FOR 2005/06 For seaso
Page 21 and 22: DRILL TEMPLATE 92 W 1. Compatibilit
Page 23 and 24: The arrow (2) on the CYBER bridge s
Page 25 and 26: DRILL TEMPLATE 94 W 4 1. Compatibil
Page 27 and 28: DRILL TEMPLATE SP 2003 W 4 5 1. Com
Page 29 and 30: 7. Function Check Before the newly
Page 31 and 32: pict 23 4. Mounting Mounting the To
Page 33 and 34: 1. Compatibility Presently the dril
Page 35 and 36: Detail A 15mm 15mm RAILFLEX SystemI
Page 37 and 38: Railflex Lite Base only 15mm Boot C
Page 39 and 40: TYROLIA CARVE PLATES 2005/06 CARVE
Page 41 and 42: MOUNTING/ 39 MOUNTING OF JUNIOR BIN
Page 43 and 44: MOUNTING OF TYROLIA BINDINGS ON PLA
Page 45 and 46: MOUNTING/ 43 Ski width Art. Nr. Bra
Page 47 and 48: SYMPRO-SYMRENT-SYSTEM 2005/06 Perfo
Page 49 and 50: SYMPRO-SYMRENT-DATA OVERVIEW Drill
Page 51 and 52: test results which exceed allowable
Page 53 and 54: direction of release is outside of
Page 55 and 56: BOOT-HANDLING AND TESTING Visual In
Page 57 and 58: MAINTENANCE & SERVICE Visual Inspec
Page 59 and 60: For wide skis. For children skis. R
Page 61 and 62: pict 66 You can extract broken scre
Page 63 and 64: Problem Possible Reason Solution SY
Page 65 and 66: SPARE PARTS-LINE 2005/06 MOJO 11 MO
Page 67 and 68: SPARE PARTS-LINE 2005/06 S Y M P R
Page 69 and 70: SCREW OVERVIEW-LINE 2004/05 HD 14 R
Page 71: CLASSIFY YOURSELF DETERMINING YOUR
Page 75 and 76: This section must be read, and thor
Page 77 and 78: device supplier to verify that thei
Page 79 and 80: Retailer Agreements and Indemnifica
Page 81 and 82: THE TYROLIA LIMITED WARRANTY TYROLI
Page 83 and 84: Racing (X) Bindings Certain binding
Page 85 and 86: Skiers Requesting Settings not Reco
Page 87 and 88: Shop Name Phone Address City State,
Page 89 and 90: CHIP TECHNOLOGY USED FOR RENTALS In
Page 91 and 92: CLASSIFY YOURSELF DETERMINING YOUR
Page 93: HTM Sport- und Freizeitgeräte AG A
show all

Technical Manual 2005/06 - Tyrolia

Create successful ePaper yourself

Delete template?

Save as template?