Technical Manual 2005/06 - Tyrolia

More documents

Recommendations

Info

38 / MOUNTING MOUNTING PROCEDURE TYROLIA CARVE PLATES 1. General For proper mounting use drill template 92 W. The compatible binding-plate combinations can be found in the compatibility chart. All TYROLIA CARVE Plates can be used for ski’s 140 cm and longer. If mounted on ski’s shorter 140 cm the screws have to be replaced by shorter ones, see screw chart on page 64. For mounting SP 70 ABS, SL 70 ABS, SL 70 or SR 70 on TYROLIA CARVE Plates you have to replace the pre-mounted screws by screws with 8 mm penetration depth. Only with these screws can we guarantee the right pullout strength (see page 39). 2. Adjusting the Drill Template 92 W Unlock the adjustment lever (1) by rotating it counter clockwise and push the template together as far as possible (23 cm). Fix the position by rotating the adjustment lever (1) clockwise until it stops (see template 92). 3. Positioning the Drill Template Open the jaws (4) of the template by rotating the handles (5) and place it on the ski with the boot midpoint indicator aligned with the mounting mark of the ski. For ski boot tip mounting align the corresponding sole length mark on the sticker (pict 47) with the boot tip mounting mark on the ski. Important! When mounting Rental bindings the boot midpoint indicator should be behind the mounting mark, in accordance with the enclosed table (page 40). For older drill templates stickers can be ordered from your local TYROLIA distributor: Sticker Boot tip – art. nr. 159 03 83. 4. Drilling the holes If not otherwise specified by the ski manufacturer, use a 4.1 Ø x 9.0 mm drill bit for skis 140 cm and longer. For ski shorter than 140 cm use a 4.1 Ø x 7.0 mm drill bit. Drill the holes using the appropriate TYROLIA drill bit. After drilling, drop some TYROLIA glue into the clean holes. This lubricates the screws and seals the hole. 5. Mounting Place the front part of the plate over the holes and fasten the screws. Then place the back part over the holes and fasten the screws. Determine the boot sole length with the TYROLIA Rental boot caliper and place the binding on the Carve Plate corresponding with the appropriate printed length markings. Mount the binding in accordance with the procedures in the <strong>Technical</strong> <strong>Manual</strong>. For ski boot tip oriented mounting only pict 47
MOUNTING/ 39 MOUNTING OF JUNIOR BINDINGS ON TYROLIA CARVE PLATES OR ON SKIS ≥ 140 CM For mounting SL 70, SL 70 ABS, SR 70 and SP 70 ABS on TYROLIA CARVE Plates or on skis, 140 cm and longer, replace the premounted screws by screws with 8 mm penetration depth. Only with these screws can we guarantee the right pullout strength (see table). 162 639 5,5 x 9,0 162 401 162 488 5,5 x 19,5 5,5 x 15,5 162 383 5,5 x 21,5 162 639 5,5 x 9,0 162 376 162 426 5,5 x 16,9 5,5 x 13,4 162 416 5,5 x 19,4 160 018 5,5 x 18,5 160 018 5,5 x 18,5 160 018 5,5 x 18,5 162 458 5,5 x 29,0 160 031 5,5 x 20,5 160 031 5,5 x 20,5 162 423 5,5 x 21,5 162 461 5,5 x 32,5
Page 1 and 2: Technical Manual 2005/06 www.tyroli
Page 3 and 4: Ski bindings 2005/2006 Active safet
Page 5 and 6: Faster adjustment to any boot sole
Page 7 and 8: Double FREE FLEX Double FREE FLEX I
Page 9 and 10: Gliding on rails Mounting without d
Page 11 and 12: 03 04 DIAGONAL Toe Active protectio
Page 13 and 14: Super Light - the lightweight Now a
Page 15 and 16: RETAIL / 13 PARTS-REFERENCE CHART R
Page 17 and 18: RENTAL / 15 PARTS-REFERENCE CHART R
Page 19 and 20: NEW TEMPLATES FOR 2005/06 For seaso
Page 21 and 22: DRILL TEMPLATE 92 W 1. Compatibilit
Page 23 and 24: The arrow (2) on the CYBER bridge s
Page 25 and 26: DRILL TEMPLATE 94 W 4 1. Compatibil
Page 27 and 28: DRILL TEMPLATE SP 2003 W 4 5 1. Com
Page 29 and 30: 7. Function Check Before the newly
Page 31 and 32: pict 23 4. Mounting Mounting the To
Page 33 and 34: 1. Compatibility Presently the dril
Page 35 and 36: Detail A 15mm 15mm RAILFLEX SystemI
Page 37 and 38: Railflex Lite Base only 15mm Boot C
Page 39: TYROLIA CARVE PLATES 2005/06 CARVE
Page 43 and 44: MOUNTING OF TYROLIA BINDINGS ON PLA
Page 45 and 46: MOUNTING/ 43 Ski width Art. Nr. Bra
Page 47 and 48: SYMPRO-SYMRENT-SYSTEM 2005/06 Perfo
Page 49 and 50: SYMPRO-SYMRENT-DATA OVERVIEW Drill
Page 51 and 52: test results which exceed allowable
Page 53 and 54: direction of release is outside of
Page 55 and 56: BOOT-HANDLING AND TESTING Visual In
Page 57 and 58: MAINTENANCE & SERVICE Visual Inspec
Page 59 and 60: For wide skis. For children skis. R
Page 61 and 62: pict 66 You can extract broken scre
Page 63 and 64: Problem Possible Reason Solution SY
Page 65 and 66: SPARE PARTS-LINE 2005/06 MOJO 11 MO
Page 67 and 68: SPARE PARTS-LINE 2005/06 S Y M P R
Page 69 and 70: SCREW OVERVIEW-LINE 2004/05 HD 14 R
Page 71 and 72: CLASSIFY YOURSELF DETERMINING YOUR
Page 73 and 74: If the intersection of the row and
Page 75 and 76: This section must be read, and thor
Page 77 and 78: device supplier to verify that thei
Page 79 and 80: Retailer Agreements and Indemnifica
Page 81 and 82: THE TYROLIA LIMITED WARRANTY TYROLI
Page 83 and 84: Racing (X) Bindings Certain binding
Page 85 and 86: Skiers Requesting Settings not Reco
Page 87 and 88: Shop Name Phone Address City State,
Page 89 and 90: CHIP TECHNOLOGY USED FOR RENTALS In
Page 91 and 92:
CLASSIFY YOURSELF DETERMINING YOUR
Page 93:
HTM Sport- und Freizeitgeräte AG A
show all

Technical Manual 2005/06 - Tyrolia

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?