You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
28 / MOUNTING<br />
DRILL TEMPLATE SR 2003<br />
4<br />
1. Compatibility<br />
Presently the drill template SR 2003 W is valid for:<br />
SR 100,<br />
SR 70,<br />
SR 45,<br />
CARVE PLATE 13 SLR (only if mounted for Rental),<br />
CARVE PLATE 9 SLR (only if mounted for Rental),<br />
JUNIOR RACING PLATE (only Rental - SR 70)<br />
SR 100 can be used with skis 140cm and longer.<br />
The junior binding SR 70 ABS is delivered with<br />
screws for skis shorter than 140cm. If it is mounted<br />
on skis longer than 140cm or on TYROLIA Carve<br />
plates, replace them with longer screws (see<br />
screw chart in this manual – page 39).<br />
SR 45 is only for skis under 140cm.<br />
Drill template SR 2003 W can be used for ski<br />
widths from 59 to 108 mm. For other skis use the<br />
template adapter set (art. nr. 162 569). With this<br />
adapter set skis from 45 to 132mm can be<br />
mounted.<br />
Note: The standard brake for all SR bindings,<br />
except the SR 45, is the POWER BRAKE LD 78<br />
(art.nr. 162 578), which can be used for skis up<br />
to 78 mm. For ski widths from 79 to 93 mm use<br />
POWER BRAKE LD wide 93 (art.nr.162 768) and<br />
from 94 to 115 mm use POWER BRAKE LD FAT<br />
115 (art.nr.162 603).<br />
The standard brake for the SR 45 is the SL KID<br />
BRAKE 74 (art.nr. 162 399), which can be used<br />
for skis up to 74 mm, for wider skis use the SL<br />
KID BRAKE wide 84 (art.nr. 162 658), which is for<br />
skis from 75 to 84 mm.<br />
The Description of the brakes always includes a<br />
number like 74, 78, 93 or 115. This number stands<br />
for the maximum ski width in the brake area and<br />
not in the ski center!!!<br />
2. Positioning the Drill Template<br />
Open the clamping jaws (4) by rotating the clamping<br />
handles (5) and then place template on the ski.<br />
3<br />
Align the boot midsole indicator (3) for the appropriate<br />
binding model or Carve Plate with the midsole<br />
mounting mark on the ski.<br />
Be sure the template is evenly seated against the<br />
ski’s top surface.<br />
Release clamping handles (5) and attach the<br />
template firmly to the ski.<br />
Note: Some ski manufactures do not use the<br />
center of boot sole location method. Always follow<br />
the ski manufacturer’s instructions.<br />
3. Drilling the holes<br />
If not otherwise specified by the ski manufacturer,<br />
for all SYMRENT adult models use a 4,1 Ø x 9,0 mm<br />
drill bit for skis 140 cm and longer.<br />
For ski shorter than 140 cm use a 4,1 Ø x 7,0 mm<br />
drill bit. Drill through the appropriate bushings<br />
(see table)<br />
Model Color of Indicator<br />
SR 100 Yellow<br />
SR 70 Blue (q-R)<br />
SR 70 White (i-J)<br />
SR 45 Red (b-o)<br />
SR 45 Green (j-w/F)<br />
CARVE PLATES Black<br />
If required by the ski manufacturer, tap the hole.<br />
After drilling place a drop of TYROLIA glue into the<br />
holes. It lubricates the screws and seals the holes<br />
(pict 23).<br />
5
Change language