Technical Manual 2005/06 - Tyrolia

DRILL TEMPLATE 92 W
1. Compatibility
Presently the drill template 92 W is valid for:
MOJO 20 (X),
FREE FLEX PLUS 20 (X),
FREE FLEX PLUS 18 (X),
FREE FLEX PLUS 15 (X),
FREE FLEX PLUS 17,
FREE FLEX PLUS 14,
FREE FLEX PLUS 11,
LD 12 CYBER,
LD 12,
SLD 11 ABS,
MOJO 15,
MOJO 11,
All TYROLIA adult bindings can be used with skis
140 cm and longer. The junior bindings SL 70 ABS
and SL 70 are delivered with screws for skis
shorter than 140 cm. If they are mounted on skis
longer than 140cm or on TYROLIA Carve plates,
replace them with longer screws (see screw
chart in this manual-page 39).
Drill template 92 W can be used for ski widths
from 59 mm to 108 mm. For other skis use the
template adapter set (art. nr. 162 569). With this
adapter set, skis from 45 to 132 mm can be
mounted.
Note: TYROLIA offers two different types of
brakes for adult bindings – the POWER BRAKE
and the SL BRAKE. Refer to the brake overview
on page 42 for brake and binding compatibility.
POWER BRAKE
The standard brake, the POWER BRAKE LD 78
(art.nr. 162 578), can be used for skis up to 78
mm. For ski widths from 79 to 93 mm use
POWER BRAKE LD wide 93 (art.nr.162 768) and
from 94 mm to 115 mm use POWER BRAKE LD
FAT 115 (art.nr.162 603).
SL BRAKE
The SL BRAKE 78-04 (art.nr. 162 642) is for skis
up to 78 mm, for wider skis use the SL BRAKE
wide 90 (art.nr. 162 755), which is for skis
ranging from 79 mm to 90 mm.
1
SL110 CARVE ABS,
SL110 ABS,
SL100 ABS,
SL110,
SL100,
SLW 90 ABS,
FREE FLEX JUNIOR RACE 11,
SL 70 ABS,
SL 70,
CARVE PLATE 13 SLR,
CARVE PLATE 9 SLR,
JUNIOR RACING PLATE
3
2
MOUNTING / 19
JUNIOR BRAKE
The SL JUNIOR BRAKE 72-05 (art.nr.162 764)
can be used for ski widths up to 72 mm for wider
skis, from 73-90 mm, use also SL Brake wide 90
(art.nr.162 755).
The Description of the brakes always includes a
number like 72, 78, 90, 93, 115, and so on ….
This number stands for the maximum ski width
in the brake area and not in the ski center!!!
2. Adjusting the Drill Template
To adjust the template unlock the locking lever (1)
by rotating it counter-clockwise to the far left
position.
FREE FLEX PLUS and CYBER:
Due to the center piece these bindings are limited
to ski boots with sole lengths from 257 to 362 mm.
Place the ski boot in the template and push the
template together until the stops (2) come
against the ski boot sole. Take the boot out of
the template. Position the locking lever (1) in the
mid position, then open or close the template to
the nearest centimeter mark.
For other bindings:
Place the ski boot in the template and push the
template together until the stops (2) come
against the ski boot sole. Lock the lever to the far
right position to prevent length change, then take
the boot out of the template.
For CARVE PLATE 13 SLR, CARVE PLATE 9 SLR,
and JUNIOR RACING PLATE:
See Page 38.
3. Positioning of the Drill Template
Open the clamping jaws (4) of the template by
rotating the clamping handles (5) and then place
template correctly on the ski, with the boot midsole
indicator (3) aligned with the mounting mark
on the ski. Be sure the template is evenly seated
against the ski’s top surface. Release clamping
handles to attach the template to the ski.
4
5