R&S®DST200 RF diagnostic chamber for ... - Rohde & Schwarz

WIRELESS TECHNOLOGIES | Test cellsKey component: the automatic 3D positionerThe new, optional R&S®DST-B160 automated 3D positioner(Fig. 3), for which Rohde&Schwarz has a patent pending, isthe automatic version of the existing R&S®DST-B150 manual3D positioner. The equipment under test (EUT) is attachedto a removable support at the center of the positioner andis rotated by two servomotors about the azimuth and theelevation axes. An optical sensor ensures high positioningaccuracy, allowing both axes of rotation to be automaticallyreset to a defined start position. The automated 3D positioneris remotely controlled via its RS-232-C interface. TheR&S®AMS32 OTA performance measurement software andthe R&S®EMC32 EMC measurement software include driversfor this interface.The servomotors and the motor control unit are accommodatedin the RF shielded bottom compartment of theR&S®DST200, preventing EMI leakage to the outside whichcould affect receiver sensitivity measurements. The positioneris made of a very low relative permittivity material to minimizefield perturbation in the EUT quiet zone.New, cross-polarized test antennaIn OTA and RSE measurements, a series of tests are performedduring which the EUT transmits or receives ϕ and θorthogonally polarized fields. Rohde&Schwarz now offersan antenna suitable for performing these measurements:the new R&S®DST-B210 cross-polarized test antenna. It hastwo sections arranged at right angles and connected to twoRF ports. The compact antenna achieves broadband radiationcharacteristics in the frequency range from 70 MHz to 12 GHzand features a high cross-polarization ratio. The measurementdistance between the center of the 3D positioner and the testantenna is approx. 280 mm. Path loss calibration tables for alltest antennas compatible with the R&S®DST200 can be foundon the Rohde&Schwarz website. These tables can be used tocarry out high-precision absolute-level measurements. Testantennas are easily interchanged after opening the top coverof the R&S®DST200.Typical measurementsA-GPS testingCompared to standalone GPS, assisted GPS (A-GPS) reducesthe time needed to calculate the position of a wireless device.In addition to satellite information, A-GPS uses informationfrom the base station, such as accurate coordinates of the cellbase stations and precise time information. A-GPS capabilityis a key requirement in order to meet the US Federal CommunicationsCommission (FCC) wireless 911 rules requiring serviceproviders to deliver fast and reliable location informationeven under poor signal conditions.The new R&S®DST-B160 automated 3D positioner and theR&S®DST-B210 cross-polarized test antenna are mandatoryoptions for performing A-GPS measurements with theR&S®DST200. The R&S®SMU200 vector signal generator simulateseight satellites, whose downlink signals are applied tothe test antenna in the R&S®DST200 in the ϕ and θ polarizationplanes (Fig. 4, example 3). The EUT extracts informationsuch as position data and received signal level from the satellitedata and sends it to the R&S®CMU200 universal radiocommunication tester via a cellular link.A-GPS measurements in line with CTIA 3.1 can be very timeconsuming.Testing multistandard smartphones takes severalMeasurementOTA SISOOTA MIMODescriptionOver-the-air performance test in line with CTIA 3.1 TRP and TIS,GSM, WCDMA, CDMA 2000®, LTEOver-the-air performance test:transmit diversity, spatial multiplexing modesA-GPS Assisted GPS performance test in line with CTIA 3.1Coexistence Simultaneous operation of two cellular or wireless services (e. g.GSM and WLAN)DesenseVerification of OTA sensitivity degradation caused by internal EUTEMI sources (self-interference)EMI scanRSEQuick detection of EMI sources within the RF operating band(in-band emissions)Radiated spurious emissions measurement, e. g. to verify compliancewith specified limits in line with ETSI EN 301 908 (WCDMA) orsimilar standardsFig. 2 The R&S®DST200 RF diagnostic chamber enables a wide range ofmeasurements in R&D, quality assurance and product qualification.Fig. 3 The R&S®DST-B160 automated 3D positioner.NEWS 205/12 17

WIRELESS TECHNOLOGIES | Test cellshours, for example. The compact R&S®DST200 makes it possibleto perform such measurements right on the lab bench.Product optimization takes place in the lab, and developersno longer require constant access to large OTA test chambers,which are often not available at short notice.RSE measurements –mandatory for all wireless devicesAll wireless devices need to be tested for radiated harmonicsof the carrier frequency or other spurious emissions (radiatedspurious emissions, RSE). Measured values must complywith specified limits in line with 3GPP, ETSI or FCC standards,for example. RSE measurements can be made using a simpletest setup with the R&S®DST200, an R&S®CMW500and an R&S®ESU EMI test receiver (Fig. 4, example 4). TheR&S®OSP130 open switch and control platform connectsthe ϕ or θ polarization plane of the test antenna to the testreceiver input.MIMO performance testing made easyThe performance gain achieved with 2×2 MIMO in the downlink– data throughput twice as high as with SISO – has to beverified at various stages in a product’s life cycle:❙❙In R&D, e.g. during antenna design❙❙In production, for quality assurance❙❙In servicing, for quality assurance❙❙In qualification measurementsFig. 4 Four example test setups and results for various radiated measurements with the R&S®DST200 RF diagnostic chamber.Example 1: OTA performance test; TRP, GSM900UL (ϕ polarized)UL (θ polarized)DL¸CMW 500R&S®DST 200 (R&S®DST-B160,R&S®DST-B210, R&S®DST-B270)Example 2: MIMO OTA performance test; transmit diversity, LTE¸CMW 500DL 2(θ polarized)DL 1 (ϕ polarized)ULCCDF in %11010090807060504030201000 20 40 60 80 100Data throughput in %¸DST 200 (¸DST-B160,¸DST-B210, ¸DST-B270)CCDF at –105.00 dBmCCDF at –123.50 dBmCCDF at –124.50 dBmCCDF at –124.00 dBmCCDF at –122.50 dBmCCDF at –123.00 dBm18

WIRELESS TECHNOLOGIES | Test cellsPass/fail measurements and qualification measurements onMIMO-enabled wireless devices can be performed usinga compact and simple test setup with the R&S®DST200RF diagnostic chamber (Fig. 4, example 2). All LTE parameterscan be configured with the R&S®AMS32 measurementsoftware and the R&S®AMS32-K31 option (Fig. 5). The twodownlink signals from the R&S®CMW500, which simulatesthe base station, are connected to the R&S®DST-B210 crosspolarizedtest antenna. The automated 3D positioner alignsthe EUT in any desired orientation in the polar coordinate systemto provide a complete picture of the spatial MIMO characteristics.Receiver sensitivity is plotted in a 3D diagram thatreveals any sensitivity degradation in partial areas. The averagedata throughput is plotted versus the received signal level.LTE parameterLTE bandSettings for LTE link1 to 41, FDD, TDD, depending on EUT capabilitiesRadio channels e. g. 5180 to 5279 for LTE FDD 13ModulationResource blocks 1 to 100Start of resource block 0 to 99Transport block size index 0 to 26BandwidthMIMO modeQSPK, 16QAM, 64QAM1.4 / 3 / 5 / 10 / 15 / 20 MHztransmit diversity, open and closed loop spatialmultiplexingFig. 5 Configuration of MIMO measurements using the R&S®AMS32 OTAperformance measurement software and the R&S®AMS32-K31 option.Example 3: A-GPS testGPS (ϕ polarized)GPS (θ polarized)¸OSP130¸SMU 200¸CMU 200Common linkDL / UL¸DST 200 (¸DST-B160,¸DST-B210, ¸DST-B270)Example 4: RSE test¸OSP130¸ESU8¸CMW 500Highpass filterϕ polarizedθ polarizedCommon linkDL / UL¸DST 200 (¸DST-B160,¸DST-B210, ¸DST-B270)Level in dBm–25RSE limit value–30–35–40–45–50–55–60–65–70–75–802.2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8Frequency in GHzNEWS 205/12 19

WIRELESS TECHNOLOGIES | Test cellsExcellent correlation of results between theR&S®DST200 and larger OTA test chambersFig. 6 reveals statistical performance, showing the cumulativedistribution functions (CDF) for the results obtained with threedifferent test chambers. The EUT was operated in LTE MIMOtransmit diversity mode, and receiver sensitivity was measuredwith the EUT set to six spatial orientations. The measurementsmade with the R&S®DST200 RF diagnostic chamberwere repeated in order to verify reproducibility of resultsobtained with the test chamber.The best statistical sensitivity was obtained with the OTA­reference test chamber (5 m × 5 m × 5 m), with 50 % ofall antenna constellations yielding at least 90 % of themaximum data throughput at a downlink power density ofP iso≈ –127 dBm/15 kHz referenced to an ideal isotropic radiator.The R&S®R-Line compact test chamber (1.7 m × 1.6 m ×2.2 m) and the R&S®DST200 delivered sensitivity 1 dB and2 dB lower, respectively, for the same test parameters. Themeasurements also exhibited a high level of reproducibilityfor the tests performed with the R&S®DST200, with resultingCDF graphs differing by no more than 0.5 dB.SummaryThe R&S®DST200 RF diagnostic chamber together with itsnew options enables a wide range of automated OTA andRSE test capabilities, while offering the most compact sizeon the market. The R&S®DST-B160 automated 3D positionerand the test equipment are controlled using the R&S®AMS32and R&S®EMC32 measurement software. Results are generatedin the same way as with large OTA or EMC test chambers.These features combine to open up new applications inR&D and quality assurance in production and subsequent servicingby network operators. Rohde&Schwarz will continueto create new options and add-ons to make the R&S®DST200even more flexible.Erwin Böhler; Adam TankielunThe article starting on page 12 discusses typical RSE measurementson LTE wireless devices during development usingthe R&S®DST200 RF diagnostic chamber.Result correlation for three test chambersCDF in %1009080706050403020100–130 –128 –126 –124 –122 –120 –118 –116P iso[dBm/15 kHz]OTA referencetest chamberOTA referencetest chamber¸R-Line¸DST 200 #1¸DST 200 #1¸R-Line ¸DST 200Abbreviations3GPP 3rd Generation Partnership ProjectA-GPS Assisted global positioning systemCDF Cumulative distribution functionCTIA Cellular Telecommunications Industry AssociationDL DownlinkEMI Electromagnetic interferenceETSI European Telecommunications Standards InstituteFCC Federal Communications CommissionFDD Frequency division duplexMIMO Multiple input multiple outputOTA Over-the-airRSE Radiated spurious emissionsSISO Single input single outputTD Transmit diversityTDD Time division duplexTIS Total isotropic sensitivityTRP Total radiated powerUL UplinkWCDMA Wideband code divison multiple accessFig. 6 CDF results obtained with three different RF test chambers forreceiver performance tests in LTE transmit diversity mode.20