Profibus System Integration PDF 4.03MB - Schneider Electric

More documents

Recommendations

Info

Considering a Premium platform supporting 5 Profibus modules, the maximumnumber of instruments which one can connect will be equal to 40 (Nb max maininstrument/) multiplied by 5 (Nb max Master/PLC) = 200 instruments maximum byPLC.The following table summarizes 3 sample calculations.TSX PBY100 : 242 words IN / 242 data words OUTNB masters per PLC(see table above)5NB Instruments per master 10 20 40 maxI/O data size on ProfibusMaximum instruments perPLC(Instruments * Master)WordsInWordsOutWordsInWordsOutWordsInWordsOut60 30 120 60 240 12050 100 200 maxThe Profibus PTQ-PDPMV1 Coupler on a QuantumA Quantum configuration makes it possible to use up to 6 PTQ-PDPMV1 modules,including the other communication modules and the 141 MMS425 01 module. Thesemodules cannot be placed in extension racks or remote dropThe PTQ-PDPMV1 module has an I/O interface for cyclic exchanges of 768 inputwords and 768 output words.As previously, we consider a median number of 2 measurements per instrument.Because a measurement occupies 2.5 words, we will thus have 5 input words perinstrument.For a PTQ-PDPMV1 module, the maximum number of instruments will be equal to:768 (I/O data size) divided by 5 (input words per instrument) =153 instrumentsmaximum, however this value is limited to the maximum number of slaves availableon Profibus; therefore a total of 124 instruments can be connected.Please note that for this calculation, we use the most important data number,specifically the number for the input data.42
The following table summarizes 3 sample calculations:PTQ_PDPMV1 : 768 words IN / 768 words OUTNB masters per PLC(see table above)NB Instruments permaster610 50 125 maxI/O data size on ProfibusWordsInWordsOutWordsInWordsOutWordsInWordsOut50 25 250 124 625 313Maximum instrumentsper PLC(Instruments x Master)60 300 744 maxThe Profibus MNET5204 Coupler on Ethernet Using I/O ScannerThe MNET-5204 gateway exchanges data with the PLC via the I/O scanner, whichhas an I/O data size that differs according to the selected Ethernet coupler. This sizeis used to calculate the number of MNET-5204 masters which can be managed withan Ethernet coupler.The MNET-5204 gateway has an I/O interface for cyclic exchanges of 768 inputwords and 768 output words.As in the previous example, we consider a median number of 2 measurements perinstrument. Because a measurement occupies 2.5 words, we will thus have, for eachinstrument, 5 words for entry and 2.5 words for displaying.For a main MNET-5204 module, the maximum number of instruments will be equal to:768 (I/O dated size) divided by 5 (entry words per instrument) = 153 instrumentsmaximum, however this value is limited to the maximum number of slaves availableon Profibus; therefore a total of 124 instruments can be connected.Please note that for this calculation, we use the most important data number,specifically the number for the input data.The following table summarizes the maximum number of instruments and themaximum number of gateways per platform for Premium or Quantum.To carry out these calculations, it is necessary to consider all data exchanged by agateway. The data exchange zone is made up of three parts:43
Page 1: How can I...manage instrumentation
Page 5 and 6: ContentThis guide is structured acc
Page 7: Selection PhaseIntroductionObjectiv
Page 10 and 11: InstrumentationspecialistPlant proc
Page 12 and 13: Operational ConstraintsInstallation
Page 14 and 15: These directives enact rules for th
Page 16 and 17: FOUNDATION fieldbus strategy provid
Page 18 and 19: Application LayersPROFIBUS-PA guara
Page 20 and 21: Profibus Device TypesProfibus devic
Page 22 and 23: Management ToolsTo simplify the con
Page 24 and 25: Selecting the Bus MasterSelection o
Page 26 and 27: Segment Coupler.Profibus DP - RS 48
Page 28 and 29: DP/PA Linking deviceIn an attempt t
Page 30 and 31: Types of CablingBasic PROFIBUS DP/P
Page 32 and 33: Bus terminationsPROFIBUS DPFor RS 4
Page 34 and 35: The master/gateway configuration is
Page 36 and 37: Centralized Architecture Premium wi
Page 38 and 39: Design PhaseIntroductionObjectiveTh
Page 40 and 41: later, in the Properties panel. Som
Page 44 and 45: • A cyclic data field (I/O data)
Page 46 and 47: At the asset management level:DTM f
Page 48 and 49: Overview of the main parts of the D
Page 50 and 51: The following diagram is an example
Page 52 and 53: Acyclic read/writePerformed functio
Page 54 and 55: SCADA system objectsFor a SCADA pag
Page 56 and 57: Master ConfigurationOnce the device
Page 58: The asset management software can a
Page 61 and 62: Prosoft Configuration BuilderUsing
Page 63 and 64: • Click on the menu « Show Unity
Page 65 and 66: In functional view, opening the XFM
Page 67 and 68: Premium ArchitectureSetting the Pro
Page 69 and 70: • Export the CNF file for use wit
Page 71 and 72: Data Exchanged Between SyCon and Un
Page 73 and 74: TCP/IP Gateway ArchitectureSetting
Page 75 and 76: • Open the menu "Profibus DP" the
Page 77 and 78: UnityProUse the I/O scanning commun
Page 79 and 80: For the inputs, list the same area
Page 81 and 82: Prosoft Configuration BuilderUnityP
Page 83 and 84: Measure TreatmentAn instrument conn
Page 85 and 86: DiagnosisThe standard diagnosis rea
Page 87 and 88: The THRESHOLD_ADJUST_PTQadjustment
Page 89 and 90: Slaves_DP_In.pH_Device.Main_Analogi
Page 91 and 92: Slave number(last slave diagnosis)9
Page 93 and 94:
DiagnosisThe reading of the standar
Page 95 and 96:
The read/write of equipment paramet
Page 97 and 98:
Operation PhaseIntroductionThis cha
Page 99 and 100:
12The Deltabar_Meas1 example shows
Page 101 and 102:
Additional Parameter AdjustmentWith
Page 103 and 104:
Asset Management ExampleIntroductio
Page 105 and 106:
Once the parameters have been set,
Page 107 and 108:
107
show all

Profibus System Integration PDF 4.03MB - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?