Profibus System Integration PDF 4.03MB - Schneider Electric
Profibus System Integration PDF 4.03MB - Schneider Electric Profibus System Integration PDF 4.03MB - Schneider Electric
A diagnostic popup can be activated to display the standard and extended diagnosisfor a sensor.The screen capture shown above displays the various measurement states anderrors for a specific sensor.The slave address can be modified to get diagnostic information for another sensorby selecting the DIAG button.102
Asset Management ExampleIntroductionAsset Management Software allows you to execute several operations, either on-lineor off-line, specifically:Device Configuration and ParameterizationAs an example the following parameters can be modified using Asset managementtool.• Device tag, device type selection• Unit selection, date-time initialization• Bus address, device data allocation setup• Device calibration, scaling factors• Warning and alarm threshold valuesDevice Monitoring and ControlDifferent types of operation can be done such as :• Measurement tracking, actuator control• Simulated manipulationsDevice Identification and DiagnosticStandard and extended diagnosis data can be get for all instrument connected onProfibus PA. For instance :• Hardware identifier, serial number, software version• Event and alarm reportingPrincipleAfter connecting to the network, the list of equipment can be discovered automaticallyor read from an existing file.103
- Page 52 and 53: Acyclic read/writePerformed functio
- Page 54 and 55: SCADA system objectsFor a SCADA pag
- Page 56 and 57: Master ConfigurationOnce the device
- Page 58: The asset management software can a
- Page 61 and 62: Prosoft Configuration BuilderUsing
- Page 63 and 64: • Click on the menu « Show Unity
- Page 65 and 66: In functional view, opening the XFM
- Page 67 and 68: Premium ArchitectureSetting the Pro
- Page 69 and 70: • Export the CNF file for use wit
- Page 71 and 72: Data Exchanged Between SyCon and Un
- Page 73 and 74: TCP/IP Gateway ArchitectureSetting
- Page 75 and 76: • Open the menu "Profibus DP" the
- Page 77 and 78: UnityProUse the I/O scanning commun
- Page 79 and 80: For the inputs, list the same area
- Page 81 and 82: Prosoft Configuration BuilderUnityP
- Page 83 and 84: Measure TreatmentAn instrument conn
- Page 85 and 86: DiagnosisThe standard diagnosis rea
- Page 87 and 88: The THRESHOLD_ADJUST_PTQadjustment
- Page 89 and 90: Slaves_DP_In.pH_Device.Main_Analogi
- Page 91 and 92: Slave number(last slave diagnosis)9
- Page 93 and 94: DiagnosisThe reading of the standar
- Page 95 and 96: The read/write of equipment paramet
- Page 97 and 98: Operation PhaseIntroductionThis cha
- Page 99 and 100: 12The Deltabar_Meas1 example shows
- Page 101: Additional Parameter AdjustmentWith
- Page 105 and 106: Once the parameters have been set,
- Page 107 and 108: 107
Asset Management ExampleIntroductionAsset Management Software allows you to execute several operations, either on-lineor off-line, specifically:Device Configuration and ParameterizationAs an example the following parameters can be modified using Asset managementtool.• Device tag, device type selection• Unit selection, date-time initialization• Bus address, device data allocation setup• Device calibration, scaling factors• Warning and alarm threshold valuesDevice Monitoring and ControlDifferent types of operation can be done such as :• Measurement tracking, actuator control• Simulated manipulationsDevice Identification and DiagnosticStandard and extended diagnosis data can be get for all instrument connected on<strong>Profibus</strong> PA. For instance :• Hardware identifier, serial number, software version• Event and alarm reportingPrincipleAfter connecting to the network, the list of equipment can be discovered automaticallyor read from an existing file.103