Edge Evolution Programmer Installation Instructions ... - Edge Products

More documents

Recommendations

Info

06 LBZ & LLY Duramax <strong>Evolution</strong>Thermocouple and install by tightening the tapered thread end into themanifold with a 9/16” end wrench. (Ideally the tip of the fitting would be lessthan or flush with the inside of the exhaust flow path.) Tighten the fitting sothat it is securely seated. Then install the probe into the fitting, and tightenthe top nut of the fitting just tight enough to keep the probe firmly mounted.(see figure A-1) Make sure that the probe cable is positioned to allow bestpath and minimal bending, for cable routing to the top of the enginecompartment.NOTE: The probe will move approximately90 Deg. clockwise in the direction the nut istightened. Before fully tightening the nut,make sure the cable starts 90 Degrees fromthe final resting position. When tightened,the cable will be correctly positioned.Figure BCAUTION: Do not bend the probe after installed. If needed, loosen the probe nut,adjust the probe, and re-tighten. Bending the probe tubing will result in a faulty probe.CorrectIncorrectFigure C Figure D Figure E12
<strong>Evolution</strong>06 LBZ & LLY DuramaxTip: Pulling backthe wheel splashguard provideseasy access tothe exhaustmanifold fortapping the EGTcableThe EGTthermocoupleinstalled into thedrilled andtapped exhaustmanifoldFigure FFigure G3. Run the thermocouple wire along the top of the fire wall. There are threesmall black clips on the top of the fire wall, slide a zip tie behind each clipand secure the Thermocouple cable with the zip ties, this will hold thecable up and out of the way of moving engine parts. (See Figure H)Slide the suppliedzip ties behind theseclips and secure thethermocouple wire.Figure H4. You will need to run the connecter side of the thermocouple through thefire wall and connect it to the OBDII connecter. Use the main grommeton the firewall (as shown in figure I.Run thethermocouple plugthrough thisgrommet toconnect it to yourOBDII connectorFigure I13
Page 1 and 2: 2006-2007 GM Duramax 6.6L LLY / LBZ
Page 3 and 4: Evolution06 LBZ & LLY DuramaxSetup
Page 5 and 6: Evolution06 LBZ & LLY DuramaxIMPORT
Page 7 and 8: Evolution06 LBZ & LLY DuramaxWarnin
Page 9 and 10: Evolution06 LBZ & LLY DuramaxFeatur
Page 11: Evolution06 LBZ & LLY DuramaxNOTE:
Page 15 and 16: Evolution06 LBZ & LLY Duramax2. Ope
Page 17 and 18: Evolution06 LBZ & LLY Duramax5. Ins
Page 19 and 20: Evolution06 LBZ & LLY DuramaxThe ot
Page 21 and 22: Evolution06 LBZ & LLY DuramaxCustom
Page 23 and 24: Evolution06 LBZ & LLY DuramaxWidth
Page 25 and 26: Evolution06 LBZ & LLY DuramaxCleari
Page 27 and 28: Evolution06 LBZ & LLY Duramax4. For
Page 29 and 30: Evolution06 LBZ & LLY Duramax3. Sel
Page 31 and 32: Evolution06 LBZ & LLY Duramax3. Sel
Page 33 and 34: Evolution2. Select the Display opti
Page 35 and 36: Evolution06 LBZ & LLY Duramax10. Se
Page 37 and 38: 06 LBZ & LLY Duramax EvolutionRecor
Page 39 and 40: 06 LBZ & LLY Duramax Evolution4. Se
Page 41 and 42: 06 LBZ & LLY Duramax EvolutionClick
Page 43 and 44: 06 LBZ & LLY Duramax EvolutionTroub

Edge Evolution Programmer Installation Instructions ... - Edge Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?