MicroDAC 5 User's Manual - Digital Audio Corporation
MicroDAC 5 User's Manual - Digital Audio Corporation MicroDAC 5 User's Manual - Digital Audio Corporation
MONO/STEREOSelectionnCHSelectionMONO 1CH Mono input, no references.MONOMONOMONOMONODescription2CH, Option A Mono primary, one reference on LREF.2CH, Option B Mono primary, one reference on RIGHT.3CH, Option A Mono primary, two references on LREF and RREF.3CH, Option B Mono primary, two references on RIGHT and LREF.MONO 4CH Mono primary, three references on RIGHT, LREF, and RREF.STEREO 1CH Stereo input, no references.STEREO 2CH Stereo primary, one reference on LREF.STEREO 3CH Stereo primary, two references on LREF and RREF.Table 1: Filter Input ConfigurationsAs you press the MONO/STEREO and nCH selection buttons, the LEDs next toeach input gain dial will indicate the use of each channel. Cycle through themodes until you reach the one you want. Note that only the legal nCH modesare shown based on the MONO/STEREO section. For instance, you cannotselect 4CH if STEREO is selected, because STEREO 4CH is not a valid mode.The LEDs light green for primary channels and red for reference channels. Forinstance, in the MONO 2CH Option A mode, the LEFT channel LED is green andthe LREF LED is red. In the STEREO 3CH mode, the LEFT and RIGHT channelLEDs are green and the LREF and RREF LEDs are red.3.1.4.2 Bandwidth ControlUse the BW selection to choose the bandwidth at which audio will be processed.The 5 kHz bandwidth uses a sample rate of 9.8 kHz, the 10 kHz bandwidth usesa sample rate of 22.05 kHz, and the 20 kHz bandwidth uses a sample rate of44.1 kHz.Regardless of the sample rate at which audio is processed, the TOSLINK outputalways uses a 44.1 kHz sample rate.3.1.4.3 Highpass FilterUse the HPF button to turn the highpass filter on and off. When the button is in,the HPF is applied.3.1.4.4 Automatic Gain ControlUse the AGC button to turn the automatic gain control on and off. When thebutton is in, the AGC is applied.Page 7
- Page 1: Multi-Channel Reference CancellerUS
- Page 7: 1 Overview1.1 IntroductionMicroDAC
- Page 11: 3 Standalone ControlsControls on th
- Page 15 and 16: 4 Specifications4.1 Power9-18VDC in
- Page 17 and 18: 5 MicroDAC 5 Configuration Utility
- Page 19 and 20: 5.5 Clearing and Freezing FiltersTh
- Page 21 and 22: Figure 5-4: Mono 2CH with Reference
- Page 23: Figure 5-7: Stereo sub-menuIn stere
- Page 26 and 27: always load to an adapting state. (
- Page 28 and 29: 5.10.1 Locked Standalone Behavior a
- Page 30 and 31: MONO/STEREO settingBW settingnCH se
- Page 32 and 33: Figure 6-1: nCH Filter DialogDescri
- Page 34 and 35: When the MicroDAC 5 is running stan
- Page 36 and 37: changes suddenly, requiring a new f
- Page 38 and 39: Page 32
- Page 40 and 41: 2. If .NET 2.0 is not already insta
- Page 42 and 43: 5. When Setup has completed the ins
- Page 44 and 45: . You will see a window asking if t
- Page 46 and 47: 7.2 Windows Vista Installation Inst
- Page 48 and 49: 5. Setup will then install the nece
- Page 50: 9. Next, before running the MicroDA
MONO/STEREOSelectionnCHSelectionMONO 1CH Mono input, no references.MONOMONOMONOMONODescription2CH, Option A Mono primary, one reference on LREF.2CH, Option B Mono primary, one reference on RIGHT.3CH, Option A Mono primary, two references on LREF and RREF.3CH, Option B Mono primary, two references on RIGHT and LREF.MONO 4CH Mono primary, three references on RIGHT, LREF, and RREF.STEREO 1CH Stereo input, no references.STEREO 2CH Stereo primary, one reference on LREF.STEREO 3CH Stereo primary, two references on LREF and RREF.Table 1: Filter Input ConfigurationsAs you press the MONO/STEREO and nCH selection buttons, the LEDs next toeach input gain dial will indicate the use of each channel. Cycle through themodes until you reach the one you want. Note that only the legal nCH modesare shown based on the MONO/STEREO section. For instance, you cannotselect 4CH if STEREO is selected, because STEREO 4CH is not a valid mode.The LEDs light green for primary channels and red for reference channels. Forinstance, in the MONO 2CH Option A mode, the LEFT channel LED is green andthe LREF LED is red. In the STEREO 3CH mode, the LEFT and RIGHT channelLEDs are green and the LREF and RREF LEDs are red.3.1.4.2 Bandwidth ControlUse the BW selection to choose the bandwidth at which audio will be processed.The 5 kHz bandwidth uses a sample rate of 9.8 kHz, the 10 kHz bandwidth usesa sample rate of 22.05 kHz, and the 20 kHz bandwidth uses a sample rate of44.1 kHz.Regardless of the sample rate at which audio is processed, the TOSLINK outputalways uses a 44.1 kHz sample rate.3.1.4.3 Highpass FilterUse the HPF button to turn the highpass filter on and off. When the button is in,the HPF is applied.3.1.4.4 Automatic Gain ControlUse the AGC button to turn the automatic gain control on and off. When thebutton is in, the AGC is applied.Page 7