Contents - Peavey.com
Contents - Peavey.com Contents - Peavey.com
COAHVECTION DIAGRAMSThere are many ways to connect the Tube Fex into your instrument system. Shown here are somerecommended hookups to give you optimd performance in some common situations.1. Using the Tube Fex direct into a mono guitar amp.This is the basic setup many clubband guitarists use. To hook up:~2 Connect your guitar to the Signal Input jack on the Tube Fex.b Connect the Left/Mono Unbalanced audio output to the input of the guitar amp.A If the signal from the Tube Fex overloads the input of your guitar amp, press the Global button toaccess the [GLOBI display and adjust the output level by placing the cursor under Out and pressingthe v button until the overload condition disappears.Tube FexClassic 30Chapter ISetup
2. Using the Tube Fex with a separate amplifier and speakers.This is a typical home, practice, or stage setup where the Tube Fex is not directly connected into the PA.system, but played through a separate amplifier and speakers. To hook up:ti Connect your guitar to the Signal Input jack on the Tube Fex.$3 Connect the Left/Mono and Right Unbalanced Outputs (stereo) to the Left and Right Inputs of theamplifier, respectively. For mono opemtioa use the LeJ?t/Mono Output only.ti If you haven’t already done so, connect the Left and Right Outputs of the amplifier to speakers.Classic” Series 50150Classic’ 41 OE72 Chapter 7 Setup
- Page 2 and 3: AIntended to alert the user to the
- Page 4 and 5: Quick StartIn an effort to make usi
- Page 6 and 7: Introduction(obligatory Opening9Con
- Page 8 and 9: Chapter 1SetupTU6EFEX’”TUBE GUI
- Page 12 and 13: 3. Using a separate preamp, distort
- Page 14 and 15: 5. Direct connection to a mixing co
- Page 16 and 17: Chapter 2OverviewGETTING STARTEDAft
- Page 18 and 19: CHROMATIC TUNERThe Tube Fex comes w
- Page 20 and 21: PERFORMANCE PARAMETER CONTROLMost e
- Page 22 and 23: The format of the IMIDI lxmk select
- Page 24 and 25: To dump a set of presets to an exte
- Page 26 and 27: Chapter 5 RAM CartridgeThe optional
- Page 28 and 29: Program Mapping‘TWX the night bef
- Page 30 and 31: 10. Press the right arrow button on
- Page 32 and 33: 3. Position the cursor under DP; us
- Page 34 and 35: Clean, Crunch, Lead parameters (Pas
- Page 36 and 37: Compressor ccn)The Compressor effec
- Page 38 and 39: The versatile Chorus effect allows
- Page 40 and 41: This delay creates a stereo delay f
- Page 42 and 43: Pitch 1 and Pitch 2 (PI and P2)In o
- Page 44 and 45: Clussic EQ (CQ)The Classic Equalize
- Page 46 and 47: Envelope Filter (EF)The Envelope Fi
- Page 48 and 49: 71~ The Thr (Threshold) parameter s
- Page 50 and 51: Appendix B MIDI ImplementationModel
- Page 52 and 53: Levels:Reverb:Overdrive:Chorus:Dela
- Page 54 and 55: Effects can be added to the current
- Page 56 and 57: FX-TYPE 9:Classic EQPRAM0 = Low Gai
- Page 58 and 59: FX-TYFE $13: Stereo SimdutorPRAM0 =
COAHVECTION DIAGRAMSThere are many ways to connect the Tube Fex into your instrument system. Shown here are somere<strong>com</strong>mended hookups to give you optimd performance in some <strong>com</strong>mon situations.1. Using the Tube Fex direct into a mono guitar amp.This is the basic setup many clubband guitarists use. To hook up:~2 Connect your guitar to the Signal Input jack on the Tube Fex.b Connect the Left/Mono Unbalanced audio output to the input of the guitar amp.A If the signal from the Tube Fex overloads the input of your guitar amp, press the Global button toaccess the [GLOBI display and adjust the output level by placing the cursor under Out and pressingthe v button until the overload condition disappears.Tube FexClassic 30Chapter ISetup