DKG-705 AUTOMATIC MAINS FAILURE AND REMOTE START ...

More documents

Recommendations

Info

DATAKOMDKG-705 User’s ManualNo: FUNCTION000 Choke Relay001 Preheat Relay002 Start Relay003 Alarm Relay (timed)004 Generator Contactor Relay005 Mains Contactor Relay006 Fuel Relay007 Stop Relay008 Load Shedding Relay009 Alarm Relay (without timeout)010 Load Contactor relay for dual011 Auto ready012 Master request relay for dual013 not used014 not used015 not used016 Shutdown: Digital Input_0017 Shutdown: Digital Input_1018 Shutdown: Digital Input_2019 Shutdown: Digital Input_3020 Shutdown: Digital Input_4021 Shutdown: Digital Input_5022 Shutdown: Digital Input_6023 Shutdown: Digital Input_7024 not used025 Shutdown: Gen Under-Frequency026 Shutdown: Gen Over Frequency027 Shutdown: High Battery Voltage028 Shutdown: Low Fuel Level029 Shutdown: High Oil Te mp. Mea.030 Shutdown: High Temp. Measured031 Shutdown: Low Oil Pressure Mea.032 Shutdown: Fail To Stop033 Shutdown: Fail To Start034 Shutdown: Genset Low Voltage035 Shutdown: Genset High Voltage036 Shutdown: Slave not available037 Shutdown: Gen phase seq. fail038 Shutdown: Low Engine Speed039 Shutdown: High Engine Speed040 Shutdown: not used041 Shutdown: not used042 Shutdown: not used043 Shutdown: not used044 Shutdown: not used045 Shutdown: not used046 Shutdown: Communication lost047 Shutdown: not used048 Load Dump: Digital Input_0049 Load Dump: Digital Input_1050 Load Dump: Digital Input_2051 Load Dump: Digital Input_3052 Load Dump: Digital Input_4053 Load Dump: Digital Input_5054 Load Dump: Digital Input_6055 Load Dump: Digital Input_7No: FUNCTION056 Load Dump: not used057 Load Dump: not used058 Load Dump: not used059 Load Dump: not used060 Load Dump: not used061 Load Dump: Gen Reverse Power062 Load Dump: Gen Excess Power063 Load Dump: Alternator Overcurr.064 Load Dump: not used065 Load Dump: not used066 Load Dump: not used067 Load Dump: not used068 Load Dump: not used069 Load Dump: not used070 Load Dump: not used071 Load Dump: not used072 Load Dump: not used073 Load Dump: not used074 Load Dump: not used075 Load Dump: not used076 Load Dump: not used077 Load Dump: not used078 Load Dump: not used079 Load Dump: not used080 Warning: Digital Input_0081 Warning: Digital Input_1082 Warning: Digital Input_2083 Warning: Digital Input_3084 Warning: Digital Input_4085 Warning: Digital Input_5086 Warning: Digital Input_6087 Warning: Digital Input_7088 Warning: Synchronization Fail089 Warning: Gen Under-Frequency090 Warning: Gen Over-Frequency091 Warning: High Battery Voltage092 Warning: Low Fuel Level093 Warning: High Oil Temp. Mea.094 Warning: High Temp. Measured095 Warning: Low Oil Pressure Mea.096 Warning: Mains Phase Seq. Fail097 Warning: not used098 Warning: Charge Failure099 Warning: Low Battery Voltage100 Warning: AVR Control Fail101 Warning: GOV Control Fail102 Warning: Low Engine Speed103 Warning: High Engine Speed104 Warning: Mains Fail at Parallel105 Warning: Mains Reverse Power106 Warning: Mains Freq. Failure107 Warning: No Mains Frequency108 Warning: ROCOF (df/dt) Failure109 Warning: Vector Shift (df/dt) Fail110 Warning: Communication lost111 Warning: not used705-UE.doc - 46 -
DATAKOMDKG-705 User’s ManualProgram Group: 9This program group defines the characteristics of the Analog sensors.The DKG-705 unit has 4 analog sensor inputs. These are:-Coolant temperature sensor input,-Oil temperature sensor input-Oil pressure sensor input,-Fuel level sensor input.The analog inputs are capable of measuring resistor values between 0 and 5000 ohms. Thanks tothe programmable characteristics, the DKG-705 may be adapted to any brand and type of sensor.Each sensor’s characteristics are defined using a maximum of 8 known points. Each point consistsof a pair of value, the first being the resistor value and the second being the corresponding analogmeasurement. For each sensor, 16 program parameters are reserved. Using defined points, the DKG-705applies a linear approximation algorithm to find the analog value corresponding to an unknown resistorvalue.For a given sensor, the points must be entered in the increasing order of resistorvalues, or faulty measurements may occur.If less than 8 points are used, unused point resistor values must be entered as ‘0’.Group Parameter Definition9 900-915 Coolant Temperature9 920-935 Oil Temperature9 940-955 Oil Pressure9 960-975 Fuel Level705-UE.doc - 47 -
Page 1 and 2: DATAKOMDKG-705 User’s ManualGense
Page 3 and 4: DATAKOMDKG-705 User’s Manual1. IN
Page 6 and 7: DATAKOMDKG-705 User’s Manual2. IN
Page 8 and 9: DATAKOMDKG-705 User’s ManualTerm
Page 10 and 11: DATAKOMDKG-705 User’s Manual3.2 D
Page 12 and 13: DATAKOMDKG-705 User’s Manual3.3 S
Page 14 and 15: DATAKOMDKG-705 User’s Manual4.1 S
Page 16 and 17: DATAKOMDKG-705 User’s Manual4.3 W
Page 18 and 19: DATAKOMDKG-705 User’s Manual5. MO
Page 20 and 21: DATAKOMDKG-705 User’s Manual6. SY
Page 22 and 23: DATAKOMDKG-705 User’s Manual7. LO
Page 24 and 25: DATAKOMDKG-705 User’s ManualThe D
Page 26 and 27: DATAKOMDKG-705 User’s Manual8. PA
Page 28 and 29: DATAKOMDKG-705 User’s Manual10. P
Page 30 and 31: DATAKOMDKG-705 User’s Manual11. L
Page 32 and 33: DATAKOMDKG-705 User’s Manual13. E
Page 34 and 35: DATAKOMDKG-705 User’s Manual17. P
Page 36 and 37: DATAKOMDKG-705 User’s ManualProgr
Page 38 and 39: DATAKOMDKG-705 User’s Manual5 522
Page 40 and 41: DATAKOMDKG-705 User’s ManualGroup
Page 50 and 51: DATAKOMDKG-705 User’s Manual10 A2
Page 54 and 55: DATAKOMDKG-705 User’s ManualThe e
Page 56 and 57: DATAKOMDKG-705 User’s Manual20. T
Page 58: DATAKOMDKG-705 User’s ManualGense

DKG-705 AUTOMATIC MAINS FAILURE AND REMOTE START ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?