PMI Piranha G2 Manual - Paintball Solutions

More documents

Recommendations

Info

TRIGGER AND SHOOTINGTrigger will not pull backTrigger pulls back, marker will not shootTrigger action does not feel smoothMarker runs on (partially cycles more thanCheck that mechanical safety is not engaged; safety shouldbe fully pushed toward left side of marker and red o-ringon safety should be fully visibleCheck that marker is cocked, air source is correctlyattached, and air source is adequately filledCheck pin at top of trigger near trigger frame; if it catches on the edge of the frame, use center punch to tap pinback into placeCheck that air source is correctly attached and air sourceis once when trigger is squeezed) adequately filled. Checksear for wear. Check hammer o-ringfor wear and replace hammer o-ring if needed, using factoryo-ring only. Use of other than factory o-ring cancause run on.VELOCITYLowLowLowLowHighHighAdjust using velocity adjusterCheck that air source is adequately filledRemove bolt/hammer assembly and clean it; clean insidereceiver area where bolt/hammer assembly is locatedChange to a stiffer hammer springAdjust using velocity adjusterChange to a less stiff hammer springCHRONOGRAPH THE MARKER AT REGULAR INTERVALS DURING THE DAY, AS WELL AS ANY TIME THE POWERSOURCE IS REFILLED OR CHANGED, ANY TIME THE BARREL OR ANY PART IN THE POWER SYSTEM IS CHANGED,AND UPON REQUEST OF ANY PLAYER OR GAME OFFICIAL.DO NOT EXCEED 300 FPS VELOCITY.PMI Piranha 22
TROUBLESHOOTINGPAINTBALLSNot flying straightBreak in barrelDo not drop into feed tubeTwo shoot at a timeCheck for broken paint in barrel, loader, feed tube, chamber,and bolt/hammer assembly area. Disassemble andclean.Check ball retainer (RP 1160) and replace if necessaryShake loader; check loader and feed tube for broken paintCheck ball retainer (RP 1160) and replace if necessarySHOOT ONLY QUALITY PAINTBALLS. PMI PREMIUM, PMI GOLD TWO-TONE, ANDMARBALLIZER PAINTBALLS ARE RECOMMENDED FOR USE IN THE PMI PIRANHABARRELBarrel comes looseAftermarket barrel does not tightenCheck barrel o-ring; firmly tighten barrelCheck to see that the threads on the barrel matchor is difficult to tighten the threads on the receiver; ifthreading is mismatched, barrel is not designed for usewith PMI PiranhaWARNINGDO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO.CONTACT PMI, INC., FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED PMI PIRANHAREPAIR FACILITIES.BEFORE DISASSEMBLY OF THE MARKER, REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND LOADER; REMOVEPOWER SOURCE; AND REMOVE ALL GAS OR AIR FROM THE POWER SYSTEM.PAINTBALL MARKER POWER SYSTEMS MUST BE REPAIRED OR REPLACED WITH THE CORRECT PRESSURERATED COMPONENTS.PMI Piranha 23
Page 1 and 2: PMI PIRANHA OWNER’S MANUALWARNING
Page 3 and 4: All paintball markers must be chron
Page 5 and 6: 8. Before attaching power source, r
Page 7 and 8: WARNINGA COMPRESSED GAS OR AIR CYLI
Page 9 and 10: The hammer spring assembled with th
Page 11 and 12: PMI PIRANHA PARTS LOCATIONBarrelPow
Page 13 and 14: Figure 9Shown: PMI Piranha VTLVerti
Page 15 and 16: MAINTENANCE OF THE PMI PIRANHAThe P
Page 17 and 18: MAINTENANCE OF THE PMI PIRANHAREASS
Page 19 and 20: ADVANCED MAINTENANCE PROCEDURESWARN
Page 21: TROUBLESHOOTINGWARNINGDO NOT ATTEMP
Page 25: REPAIR PROCEDUREORIGINAL SALES PURC

PMI Piranha G2 Manual - Paintball Solutions

Create successful ePaper yourself

Delete template?

Save as template?