Mini5 & 6 Structured Cabling System 6 - Minitran

Mini5 & 6 Structured Cabling SystemCAT6 angled modulesCAT5e UTP Modularwallplate kitsSTRUCTURED CABLING SYSTEMS (MIN5/6) - 2Minitrans own brand low cost system inCAT5e Mini5 & CAT6 Mini6 versions.Mini5 is a conventional punchdownsystem with a 15 year system warrantywhen installed by a Mini5 partner.Mini6 has modular panels & wallplatesthat accepts the same jack (in variouscolours) for balanced performance.25 year system warranty available.see www.mini5.comMini5/6 Frames & blanksSingle gang flat frameSingle gangbevelled frameDouble gang flat frameDouble gangbevelled frame25x50 half blankMT50-1000MT50-1000BDMT50-2000MT50-2000BDMT50-BM2512.5x50 quarter blank MT50-BM125Brushed steel or brass frames on page 30.Accept Mini5 and Mini6 modulesCAT5e angled & flatmodulesAngled CAT6 UTP “Mini6”MT66-SAMKAngled CAT6 STP “Mini6” MT66-SAMSShuttered 25x50mm modules with dualpunchdown snap in jack. Label window &strain relief. Snaps into the frames (left). 2modules per single gang frame & 4 perdouble. Suitable for 32mm back boxes.Use Krone/110 tooling.Single gang 4 waywallplate & CAT5e jacks4 way shuttered wallplate unloadedwithout jacksMT50-4000CAT5e UTP “Mini5”punchdown jackRJ45PZ5WECAT5e STP “Mini5”punchdown jacksRJ45PSZ5Space saving 4 way single gang shutteredwallplate accepts "Mini5" jacks withstrain relief. (Same jacks as used in angledmodules below left).Wallplates & jacks must be orderedseparately. This wallplate is notrecommended for use with CAT6 jacksdue to bend radius considerations.Suitable for 32mm back boxes.Use punchdown tool CT 28.Single gang with 1 module& 2 quarter blanksSingle gang with 2 modulesMT50-SADPMT50-DADPDouble gang with 4 modules MT50-QADPFaceplate kits using MT50-1000/2000frames and MT50-SAMK modules shownbottom left.Fibre angled modulesST fibre moduleSC simplex fibre moduleLJ6C CAT5e module forfloor boxes & trunkingMT50-AMSTMT50-AMSCMTRJ fibre module MT50-MTRJCRMini5 25x50mm modules with labelwindow.Snaps into the frames shown topleft. Suitable for 32mm back boxes.BT modulesAngled CAT5e UTP “Mini5”MT50-SAMKAngled CAT5e STP “Mini5” MT50-SAMSFlat Cat5e UTP“Mini5”MT50-SSMKShuttered 25x50mm modules with dualpunchdown. Label window & strain relief.Snaps into the frames (above).2 modules per single gang frame & 4 perdouble. The angled module is suppliedwith a jack that snaps into the module.The flat module is one piece with thepunch down blocks at the rear. Suitablefor 32mm back boxes.Use punchdown tool CT28 for angledmodule.Krone/110 tooling for flat module.SecondaryFull MasterMT50-SESAMT50-FMSAPABXMT50-PASAMini5 UK 6 position BT socket in a25x50mm angled shuttered module. Dualtermination.MT50-SLJKLPMini5 Flat low profile dual punchdown37x25mm module with label window. Forfloorbox & trunking applications. Will notfit Mini5/6 frames.See the ‘Sharpmark’ labelling system onpage 35.Screen printing service available.6Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Mini5 & 6 Structured Cabling System“Mini5” CAT5e UTP punchdown patch panelsMini5/6 LED panels“Mini6” modular patchpanelsStandard version24 port 1U MP24T-KRO-CECBK48 port 2U MP48T-KRO-CECBKAngled port version24 port 1U MP24A-K11-C5CBK48 port 2U MP48A-K11-C5CBKStandard port or angled port UTP panels.Angled ports alleviate cable bends in thecabinet. Mini5 CT28 tool is recommendedfor the best results. Numbered ports &write on/wipe off label field.See Sharpmark labelling system onpage 35.Cable tie slots for management.Cage nuts included. Ports can be colourcoded using the modules below.Mini5 Colour codingmodulesCAT5e UTP 24 port 1UCAT6 UTP 24 port 1UMP24-EP5UMP24-EP6UTester unitMT-EPATCHWhen the tester unit is plugged into awallplate the corresponding LED port onthe patch panel lights up to identifywhere it is patched to. 110 punchdown."Mini5" CAT5e STP punchdown patch panel24 port 1U STP MP24S-C5EBKCompatible with LSA Krone & 110 punchdown tools although the Mini5 CT28 handtool is recommended for the best results.With cable ties & grounding kit.Numbered ports & write on wipe off labelfield. Sharpmark labelling system onpage 35.24 port 1U MT66-M24NCM24 port 1U withrear cable management MT66-M241U48 port 2U MT66-M48NCM48 port 2U withrear cable management MT66-M482UBlank for unusedpositions in panelMT66-BLNKAccepts the snap in CAT6 jacks below.Clip on cable management bar allowsjacks to be snapped into the panel &terminated prior to fixing the rearmngmnt into position. Numbered portsand write on/wipe off label field. Also seethe "Sharpmark" labelling system onpage 35. Cage nuts included.Mini6 CAT6 UTP & STP jacks2 - STRUCTURED CABLING SYSTEMS (MINI5/6)Standard AngledBlue PT-JB-BE PA-JB-BEGreen PT-JB-GN PA-JB-GNYellow PT-JB-YW PA-JB-YWRed PT-JB-RD PA-JB-RDTIA/EIA-606 recommends colourcoding functions within the cablinginfrastructure.Simply unscrew the black modules fittedto each group of 6 RJ45 skts in the above“Mini5” panels & fit the required colour.Blue: Horizontal cablingGreen: Network connectionsYellow: Auxiliary circuitsRed: Key telephone systemsOther colours also available"Mini5" CAT5e throughcoupler panels (UTP & STP)16 port UTP 1U PPRJ45161T524 port UTP 1U PPRJ45241T548 port UTP 2U PPRJ45482T516 port STP 1U PPRJ45161TS524 port STP 1U PPRJ45241TS548 port STP 2U PPRJ45482TS5RJ45 ports on front & rear. Just plug inyour patch cables. With numbered ports."Sharpmark" labelling system onpage 35.UTP Black CAT6 jackUTP White CAT6 jackUTP Blue CAT6 jackUTP Green CAT6 jackUTP Red CAT6 jackUTP Yellow CAT6 jackMT66-U180BKMT66-U180WEMT66-U180BEMT66-U180GNMT66-U180RDMT66-U180YWSTP CAT6 jackMT66-S180SHHigh performance CAT6 dual punch downjack compatible with LSA Krone & 110tools. With clip on cable strain relief cap.Available in various colours for codingpurposes.. Snaps into modular panelsabove. This is the same jack that is used inMini6 wallplates giving balancedperformance at each end.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk7

Mini5 & 6 Structured Cabling SystemFibre panels (fixed tray 1U)Voice PanelsFiller panelsSTRUCTURED CABLING SYSTEMS (MINI5/6) - 2Panel shown loaded and with optional(MAT107-SPOOL) cable management kit.Panels without couplersFor 8 ST couplersFor 16 ST couplersFor 24 ST couplersFor 16 MTRJ couplersFor 24 MTRJ couplersFor 8 SC duplex couplersFor 12 SC duplex couplersFor 16 SC duplex couplersFor 24 SC duplex couplersFor 12 LC duplex couplersCouplersST m/modeST s/modeSC duplex m/mode (blue)SC duplex m/mode (beige)SC duplex s/mode (metal)MTRJ (Beige)MAT10708MAT10716MAT10723MAT10719MAT10722MAT10720MAT10718MAT10721MAT10724MAT10726FCST-APBFCST-APBSFCSC-DPBFCSC-DPB-BEFCSC-DPBSFCMTRJ-APBRKBlanks & cable management kitST blankSC simplex/MTRJ blankSC duplex blankFCST-BLNKFCSC-SBLNKFCSC-DBLNKCable management kit MAT107-SPOOLMTRJ panels will also accept SC simplexcouplers shown on page 46.Mini5 fibre panels are supplied withbrackets for rack mounting, cablegrommet, cable ties and adhesive bases.An optional cable management kit (Partno MAT107-SPOOL) consisting of twofibre support bases and eight cablerouting loops for spooling excess cable isalso available.Panels are black with numbered ports.Fibre patch leads on pages 43-44.Fibre cable see page 42.50 port 1U voice panel MP50-1UTELCompatible with LSA Krone style punchdown tools although the Mini5 CT28 toolis recommended for best results. Withnumbered ports & rear cablemanagement.Cable tidy panels1U with 4 metal rings1U with 4 plastic rings1U with 5 metal ringsBrush panel (1U)HJRP-1UHJRPP-1UHJRP5-1U2U with 5 metal ringsHJRP5-2UHorizontal 19" cable tidy panels are a costeffective way of managing patch cables.HBBE-1UGives a neat appearance when patchingfrom front to back within a rack.1U2U3UPPB-1UBPPB-2UBPPB-3UB4UPPB-4UBHorizontal 19" filler panels reserve rackspace for future use and help keepinstallations manageable by acting as adivider between devices.Data/Voice adaptersSecondaryPABXFull MasterDVA-WSECDVA-WPBXDVA-PSTNISDNDVA-ISDNRJ45 plug fitted to 150mm lead with a sixway telephone socket in the adapterbody, except for the ISDN version whichhas a RJ45 socket. In the body.Mini5/6 CAT5e & CAT6 solidcableMini5 CAT5e (305Mtr boxes)UTP grey PVCUTP4M5SBUTP blue PVCUTP purple LSOHFTP grey LSOHMini6 CAT6 (305Mtr boxes)UTP grey PVCUTP4W5SBEUTP4M5SB-LSFTP4W5SB-LSUTP4M6SBUTP grey LSOHUTP4W6SB-LSLow cost cable supplied in 305 metreboxes. Approved for use in the "Mini5/6"15/25 year system warranty programme.For other cable types and brands seepages 27-28.8Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Mini5 & 6 Structured Cabling SystemMini5 CAT5e UTP patchleads with moulded bootsMini5 CAT5e STP patch leadswith moulded bootsMini6 CAT6 UTP patchleads with moulded bootsLength 100Mhz 350Mhz0.5Mtr PCTB5005* PCTM5005E*1Mtr PCTB5010* PCTM5010E*1.5Mtr PCTB5015* PCTM5015E*2Mtr PCTB5020* PCTM5020E*3Mtr PCTB5030* PCTM5030E*5Mtr PCTB5050* PCTM5050E*10Mtr PCTB5100* PCTM5100E**For coloured patch leads add thefollowing suffix:Blue = BE, Red =RD, Green = GN,Yellow = YW, Black = BK,Pink = PK, Orange = OE.No suffix required for grey.Example:Red 100Mhz 2Mtr = PCTB5020RD100Mhz or 350Mhz versions. 350Mhzleads should be used with the Mini5 15year system warranty programme inregistered installations. The boots aremoulded flush to the side of the RJ45plugs to ensure that they can beconnected to any RJ45 socket0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM5005ESPCTM5010ESPCTM5020ESPCTM5030ESPCTM5050ES10Mtr greyPCTM5100ESBoots are moulded flush to the side of theRJ45 plugs to ensure that they can beconnected to any RJ45 socket. STP leadsare 350Mhz & supplied in grey.Crossover patch leads0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM6005PCTM6010PCTM6020PCTM6030PCTM605010Mtr greyPCTM6100Boots are moulded flush to the side of theRJ45 plugs to ensure that they can beconnected to any RJ45 socket. Staggeredinternal contact design on RJ45 plugs.Mini6 CAT6 UTP LSOH patchleads with boots2 - STRUCTURED CABLING SYSTEMS (MINI5/6)Mini5 CAT5e UTP 100Mhzpatch leads (non booted)0.5Mtr1Mtr2Mtr3Mtr5MtrPCT5005E*PCT5010E*PCT5020E*PCT5030E*PCT5050E*10MtrPCT5100E**For coloured patch leads add thefollowing suffix:Blue = BE, Red =RD, Green = GN,Yellow = YW, Black = BK. No suffixrequired for grey.Example: Red 2Mtr = PCT5020ERD0.5Mtr1Mtr2Mtr3MtrPCT5005YWBK-XPCT5010YWBK-XPCT5020YWBK-XPCT5030YWBK-X5MtrPCT5050YWBK-XUTP x-over leads are made with yellowcable and a black strain relief boot onone end in order to differentiate themfrom standard patch leads.Wrap around cable labels on page 35.0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM6005LSPCTM6010LSPCTM6020LSPCTM6030LSPCTM6050LS10Mtr greyPCTM6100LSLow smoke zero halogen patch leads withslide on RJ45 boots with anti tangleblister. These patch leads should be usedwith the Mini6 25 year system warrantyprogramme in registered installations.Staggered internal contact design onRJ45 plugs.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk9

Mini5 SOHO Cabinet & AccessoriesSTRUCTURED CABLING SYSTEMS (MINI SOHO) - 2Mini5 SOHO cabinet, patch panels,switches & accessories, have beendesigned for the new emerging market ofprivate telecom/data applicationsassociated with home or small offices.Mini5 Enclosure8UMPE0812UMPE12Mini5 SOHO mini-patch enclosures arebeautifully designed with a curvedperspex lockable front door and acceptsour range of 250mm panels andaccessories.Adjustable front profiles.205mm internal depth (not includingcurved perspex door).Front door and side panels are removableto allow frame to be hung on the walland populated with all round access priorto outer case being refitted.Mini5 CAT5e FrontTermination 10" PanelPanelMini5 Voice & Data 10"Panel4 Port RJ + 4 Port BT MP08-T44Combined voice & data panel comprisingof 4 CAT5e UTP data ports and 4 BTsecondary sockets. 1U height.Mini5 Voice & ISDN 10"Panel4 Port RJ + 4 Port BT MP08-T44ISCombined voice & ISDN panel comprisingof 4 CAT5e UTP ISDN ports and 4 BTsecondary sockets. 1U height.Mini5 Voice only 10" PanelCo-Axial 10" Panels8 port unloaded MP08-C1312 port unloaded MP12-C138 port + BNC thru couplers MP08-C13C12 port + BNC thru couplers MP12-C13CCo-ax panels available with or withoutinsulated 50/75 ohm BNC throughcouplers.Cable Management &Blank PanelsCable Mng Bar 1UBlank Panel 1UBlank Panel with slot 1UMP1-CM3MP1-BP1MP1-BP1SMini5 8 Port SOHO Switch(Rack Mount)8 way UTP MP08-KRO-FECBKMini5 CAT5e dual 110/Krone compatiblefront termination 1U panel. Simply fixinto the cabinet & punch down cablesfrom the front.12 ports RJ45 MP12-TEL12 x RJ45 ports with dual punch downterminations for pins 3, 4, 5 & 6. 1Uheight.Modular 10" Panels8 port SOHO switch MT-1608SBCompact 8 port switch with uplink port &external plug in power supply.Mini5 CAT5e 10" PanelsShelf8 way UTP MP08-KRO-C5EBK12 way UTP MP12-KRO-C5EBK8 way STP MP08-KRO-C5ES12 way STP MP12-KRO-C5ESMini5 CAT5e dual 110/Krone compatible1U punch down panels in either 8 or 12ports. Punch down tooling available fromus as order part number CT28 or CT36.8 port unloaded MP08-M1UMay be loaded with a variety of jacksfound in the Mini5 and Mini6 range:Cat5e jacks see page 6Cat6 jacks see page 7Through couplers see page 31RJ11 jacks see page 31BT jacks see page 6.1U x 150mmFor cable see page 27.MP1-S15010Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Panduit Structured Cabling SystemUTP Cat5e tool-less JacksOpti-Jack Fibre ConnectorsThe Panduit Network Connectivity Groupis a world Leader in Network Solutionsoffering complete systems to connect,route, manage and identify your networkinfrastructure. Panduit specialise inmodular fully integrated networkconnectivity. The heart of the systemis an innovative Cat5e or Cat6 tool-lessjack that ensures the correct maintenanceof cable twists for high performance &reliability. 20 year component guaranteeor 15/25 year system warranty available.See www.panduit.com.emeaUTP CAT5e & CAT6 tool-lessjacksCategory 5e Tool-less JacksCat5e Black CJ5E88TBLCat5e Artic White CJ5E88TAWCat5e Blue CJ5E88TBUCat5e Red CJ5E88TRDCat5e Yellow CJ5E88TYWCat5e Orange CJ5E88TORCat5e Green CJ5E88TGNCat 5e Violet CJ5E88TVLCategory 6 Tool-less JacksCat6 Black CJ688TPBLCat6 Artic White CJ688TPAWCat6 Blue CJ688TPBUCat6 Red CJ688TPRDCat6 Yellow CJ688TPYWCat6 Orange CJ688TPORCat6 Green CJ688TPGNCat6 Violet CJ688TPVLPanduit jacks are used in faceplates,surface boxes and patch panels. The Jacksfeature a revolutionary new non-punchdown method which speeds installationtime and connector untwists to providesuperior performance with headroom.Exceeds Cat5e standards.BlackArtic WhiteBlueYellowRedGreenOrangeCJ588BBLCJ588BAWCJ588BBUCJ588BYLCJ588BRDCJ588BGNCJ588BORVioletCJ588BVLThe Original tool-less jack from Panduitmeets Cat5e standards. Use in faceplates,surface boxes and patch panels. Clear,removable cap for easy troubleshooting.No punch-down tool required; connectorcan be re-terminated up to 10 times.Termination tool page 16.STP CAT5e & CAT6 tool-lessjacksCat5e FTPCJS5E88TCat6 FTPCJS688T3STP Tool-less Jacks Snap into faceplates,modular panels and surface mount boxes.Blank ModulesWhite Blank ModuleCMBAW-XBlack Blank ModuleCMBBL-XBlank Module for use in Faceplates,Modular Panels and Consolidation/SurfaceBoxes.JackJacks (epoxy and polish)Multimode Opti-Jackfor 62.5/125 or 50/125Singlemode Opti-Jackfor 9/125PlugFJJGM5CEIFJJGS9CBUJacks (Opti-Crimp pre polished)Multimode Opti-Crimp FJJSMM5CEIjack for 62.5/125 (Tooling on page **).Multimode Opti-Crimp Jack FJJSMM50CEIjack for 50/125 (Tooling on Page **).Plugs (epoxy and polish)Multimode Plug for FJEPGM5CEI62.5/125 or 50/125Singlemode Plug for FJEPGS9CBU9/125Combining the look/feel and ease of useof familiar RJ-style copper connector withthe performance of ST/SC ferruletechnology.The Interface allows higher density fibreinstallations than are possible with STand SC connectors, saving rack space andequipment expense. Available in bothSinglemode and Multimode, Epoxy andpolish or Multimode pre-polished crimpstyle. Should be used with tight bufferedcable only.Fibre ModulesST White MultimodeST Black MultimodeMTRJ CouplerSC duplex White M/ModeCMSTAWCMSTBLCMMJEICMDBUSCAWSC duplex Black M/Mode CMDBUSCBLLC module -Available end of 2003/early 2004Fibre Modules Snap into faceplates(non-shuttered only apart from the MTRJCoupler), modular Patch Panels andconsolidation surface mount boxes.2 - STRUCTURED CABLING SYSTEMS (PANDUIT)Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk11

Panduit Structured Cabling SystemModular Faceplate KitsOne Piece SlopedFaceplates (Un-shuttered)LJ6C & 25x50mm ModulesSTRUCTURED CABLING SYSTEMS (PANDUIT) - 22 Port Single gang CFPUKS2SAW4 Port double gang CFPUKS4SAW-2GFrame & Angled Shuttered Data Port kits.Accepts CAT5e & CAT6 Jacks Shown onpage 11.Modular Faceplate Frames& InsertsPlastic Faceplate (Frames)Singlegang PlateDoublegang PlateFaceplate insertsAngled UnshutteredModule.Angled ShutteredModule.CBUKAWCBUKAW-2GCHS2AW-XCHS2SAW-XFlat Unshuttered Module CHF2AW-XSloped RecessedCHSR2AW-XUnshuttered Module.Panduit faceplates in single or doublegang size. The double gang platesrequires two Faceplate inserts, while thesingle gang frames require one. Eachinsert houses two jacks shown onpage 11.2 port single gang CFPUKS2AW3 port single gang CFPUKS3AW4 port single gang CFPUKS4AWEconomical One Piece, high density,angled non-shuttered data ports acceptsjacks shown on page 11.Surface mount Boxes1 Port CBX1AW-A2 Port CBX2AW-A4 Port CBX4AW-A6 Port CBXD6AW-A6 port Multimedia CBXF6AW-A12 port Multimedia CBXF12AW-AAccepts modules for STP, UTP. Themultimedia (copper & Fibre) boxes have aspool for cable management.Consolidation BoxesBox shown loaded with jacks and fibre kitShuttered 25x50 ModuleShuttered LJ6C ModuleCM6CESAW-XCM6CSAW-XUnshuttered LJ6C Module CM6CAW-XLJ6C Modules for use in Floor Boxesand trunking. The unshuttered versionwill accept ST fibre Modules. Jacks forthese modules shown on page 11.These modules do not fit Panduit frames.Fibre Optic Wall Boxes2 Panel Fibre Box FWME2Accepts up to 2 FAP/FMP Panels,Supports to 16 ST, 24 SC or 24 Opti-Jackterminations304.8 W x 258.6 H x58.9 Dmm4 Panel Fibre Box FWME4Accepts up to 4 FAP/FMP Panels,Supports to 32 ST, 48 SC or 48 Opti-Jackterminations409.2 W x 311.2 H x 89.4 DmmPanels For Wall BoxesUnloaded 6 way panelFMP6Accepts Fibre Optic or UTP/STP modulesPreloaded with 6 STFAP6WSTMulimode/Singlemode couplersPreloaded with 3 SCFAP3WDSCDuplex Mulimode/Singlemode couplersPreloaded with 6 SCFAP6WDSCSimplex Mulimode/Singlemode couplersBlank PanelFAPBOpticom Fibre Optic Wall Mountedenclosures include fibre optic cablerouting accessory kit and labels.Screen printing service available.Please ask for details.Sharpmark labelling system on page 35.24 Port CUFMB24BL48 Port CUFB48BLFibre conversion KitCUFF-KITUnder Floor Consolidation Point Boxsuitable for copper applications, or Fibreapplications when used with the fibreconversion kit.12Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Panduit Structured Cabling SystemMetal Modular PatchPanelsAngled Modular PanelsTelco Panels16 port 1U CP16BL24 Port 1U CP24BL24 Port 1U +cable managementCP24WSBL48 Port 2U CP48BL48 Port 2U + cablemanagementCP48WSBL72 Port high density 2U CP72BL96 Port 4U CP96BLPanels accept all Panduit Modules/jacks.Black with a white labelling area aboveeach port. The panels with managementhave a strain relief bar at the rear.Plastic Modular Panels24 Port 1U CPPLA24WBL48 Port 1U CPPA48HDWBL48 Port 2U CPPLA48WBL72 Port 2U CPPLA72WBLUsed with all Panduit Modules/jacks.Unique angled design allows cables toflow to each side of the rack andeliminates the need for horizontal cablemanagers by enabling patch cords to berouted to the sides into vertical cablemanagers.Use as part of the patch runner systemshown on page 15.CAT5e & CAT6 Punch DownPanels24 Port 1U DP24584TV2548 Port 2U DP48584TV25Can be used in 10 Base-T or 100 Base-Tapplications. The 24 port has 2 telcosockets, while the 48 port has 4 telcosockets. Velcro ties included.Voice Panels25 Port 1U VP25344KBL50 Port 1U VP50344KBLVoice Patch Panels with 25 or 50 pairsfor analogue telephone applicationsCategory 3 performance. Supports pins3,4,5 and 6. LSA punchdown.2 - STRUCTURED CABLING SYSTEMS (PANDUIT)12 Port 10inch wall panel CPP12WBLBracket for 12 Port PanelWB89D24 Port 1U Panel CPPL24WBL32 Port 1U Panel CPP32WBL48 Port 1U Panel CPP48HDWBL48 Port 2U Panel CPPL48WBLFor use with all Panduit modules/jacks.The innovative faceplate design allowsthe installer to populate the panel fromthe front. The 32 port panel is designedfor high-density. The 24 and 48 portversions benefit from labelling windows.The 12 port panel is 10 inches wide andis wall mounted using the WB89Dbracket.CAT5e 24 port 1U 110CAT5e 48 port 2U 110CAT6 24 port 1U DP6DP245E88110UDP485E88110UDP24688WGPCAT6 48 port 2U DP6 DP48688WGPPunch down patch-panels with universalwiring110 IDC blocks on Cat5e versions.DP6 punch down blocks on Cat6 versions.For DP6 "Gigapunch" CAT6 panels usepunch down tool part number GPDT.All above panels have numbered portsand write on areas for port/panelidentification.Sharpmark labelling system on page 35.Fibre Trays1U Fibre TrayFMT12U Fibre TrayFMT2Fibre trays mount to the rear of modular19" patch panels and allows quick andeasy fibre termination. Removable coverfor easy access and side and rear cableentry options. Cable management kitincluded. Use with CP24BL (1U), CP48BL(2U), CPPL24WBL(1U), CPPL48WBL(2U)modular patch panels.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk13

Panduit Structured Cabling SystemSTRUCTURED CABLING SYSTEMS(PANDUIT) - 2Panduit Cable Management System.Suitable for use with UTP, STP, coax andfibre-optic cabling systems thesemanagement panels simplify/ organizemoves, adds and changes by helping tokeep cables neat, organised andaccessible.Available for horizontal and vertical use,these panels are supplied with covers thatcompletely conceal cabling when in place.Vertical Wire CableManagementShown without clip on coverFront & Rear Management20U 101.6mm x 127mm WMPV20Side Management Panel 889mm Height.45U 101.6mm x 127mm WMPV45Side Management Panel 2108.2mmHeight.50U 101.6mm x 127mm WMPV50Side Management Panel 2413mm Height.45U 152.4mm x 152.4mm WMPVHC45Side Management Panel 2108.2mmHeight.Front Only Management20U 101.6mm x 127mm WMPVF20Side Management Panel 889mm Height.45U 101.6mm x 127mm WMPVF45Side Management Panel 2108.2mmHeight.45U 152.4mm x 152.4mm WMPVHCF45Side Management Panel 2108.2mmHeight.Vertical Panel Centre KitVertical Panel Centre Bracket WMPVCBConverts front & rear management tocentre.The vertical cable management systemoffers the option of being attached to theside of, or adjacent to standard EIA 19"racks (see page 15)These cable managers are mounted fromthe rear and are supplied with removablecovers.Hinged Horizontal NetworkCable Managers1 U Front 38 x76.2mm NCMHF12 U Front NCMHF276.2 x 76.2 mm front2 U Front & Rear NCMH276.2 x 76.2 mm (front),50.8 x 127mm (rear)Made from sturdy plastic construction,these panels help maintain highperformance copper and fibre optic cablebend radius. Fits standard EIA 19" racks.Hinges from the top or bottom ofmanagement. integral wire retainers.Patch Runner Vertical CableManagementFront & Rear Management(2139.6mm height)Front (w x d) 152.4x215.9mmRear (w x d) 152.4x139.7mmFront (w x d) 203.2x215.9mmRear (w x d) 203.2x13.7mmFront (w x d) 304.8x215.9mmRear (w x d) 304.8x139.7mmFront Only Management(2139.6mm height)Front (w x d) 152.4x215.9mmFront (w x d) 203.2x215.9mmFront (w x d) 304.8x215.9mmRear door for NCMV6Rear door for NCMV8Rear door for NCMV12PatchRunnershownon eachside ofa loadedrackNCMV6NCMV8NCMV12NCMVF6NCMVF8NCMVF12NCMV6RDNCMV8RDNCMV12RDEnd panelNCMVEPVertical cable management with Dualhinged full length door (one included),molded cable management fingers andmanagement spools to organize patchcables. For use with Panduit standardframes on page 15 and angled patchpanel on page 13.Hinged Horizontal WireManagementFront Only Management1 U Front 38.1 x76.2mm WMPFSE1 U Front, 38.1 x 50.8mm WMPLFSE2 U Front, 76.2 x 76.2mm WMPF1E2 U Front, 76.2 x 76.2mm WMPHF2EIncludes bend radius control clipat each end.Front & Rear Management1 U Front & Rear WMPSE38.1 x 76.2mm (front) 25.4 x101.6mm(rear)1 u Front & Rear WMPLSE38.1 x 50.8mm(front), 25.4 x101.6mm (rear).2 U Front & Rear WMP1E72.2 x 76.2mm (front), 50.8 x101.6mm(rear)2 U Front & Rear WMPH2E76.2 x 76.2mm (front), 50.8 x 127mm(rear)Includes bend radius control clipAvailable in 1U or 2U (rack space).19" Panel Wiring Duct managescables on both the front and the rearof a 19 inch enclosure. Includes frontduct and mounting screws. Design helpsmaintain correct cable bend radius.Keeps Cables organised and accessible.14Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Panduit Structured Cabling System45U Netframe Rack SystemStandard RackPatch-Runner CablingSystemRack shown loaded with optionalhorizontal management shown on P.14Rack45U Netframe RackCMRSW84AccessoriesHeavy Duty 450mm deep19" shelf CMRSHLF19Top centre Waterfall *End Cap*Wire Duct Accessory*Lower Trough*Upper Trough*Additional D-RingCMRSTCWCMRECCMVD4X4CMLT19CMUT19CMRSDR1Vertical Slack Mngr*CMVSMF* Waterfall mounts to top centre ofNetframe & provides additional bendradius control.* End cap mounts to side of Netframe orWire Duct Accessory* Wire Duct Accessory is 101.6 x 101.6mmslotted channel that mounts to the side ofthe frame in place of D rings.* Troughs mounts to the bottom or top ofthe rack to provide bend radious controland facilities for routing cable from onerack to another.* Vertical Slack Manager sits on the frontside of the rack to manage excess cable.The 45U Netframe is a CompletelyModular rack system which includes152mm deep channels and 16 modular D-rings for vertical cable management;metal hinged doors, top bend radiuscontrol and assembly hardware.Assembles as a 19" or 23" wide rack. Theversatile Netframe has a number ofaccessories to aid the installer with cablemanagement, storage and baying. Idealfor high density applications.45U High Standard Rack CMR19X84EIA 19" (84" high)24U High Standard Rack CMR19X47EIA 19" (47" high)Mounting ScrewsS1224-Cfor Mounting 19" Panels.This Rack can be used with all 19"PatchPanels and Horizontal CableManagement. Compatible with VerticalWire Management on page 14 or withthe innovative Patch Runner CablingSystem shown right.Blank Panels1 U DPFP12 U DPFP24 U DPFP4Filler Panels reserve rack space forfuture use and help keep installationsmanaged by acting as a divider.Mounts to standard EIA 19" racks orwall bracket.Patch-Runner is designed for maximumdensity with minimum floor space. Thestandard rack (shown left) is loaded withangled patch panels (shown on page 13),and has the Patch-Runner verticalmanagement (shown on page 14) on eachside of the rack. The cables flow from theangled panels in to the verticalmanagement without the aid ofhorizontal cable management, thusreducing cost and floor space.Hinged Wall Brackets1 U WBH12 U WBH23 U WBH34 U WBH4Mounts to wall or standard EIA 19" racks.Hinge allows easy access to cabling. Depth15.24mm. Black in colour.2 - STRUCTURED CABLING SYSTEMS (PANDUIT)Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk15

Panduit Structured Cabling SystemCAT5e & CAT6 Patch LeadsRJ45 Plug & ToolingOptical Fibre TerminationKitsSTRUCTURED CABLING SYSTEMS (PANDUIT) - 2CAT5E UTP (non booted)1 Mtr Grey UTPCH1M2 Mtr Grey UTPCH2M3 Mtr Grey UTPCH3M5 Mtr Grey UTPCH5MCAT6 UTP (non booted)1 Mtr Grey UTPSP1M2 Mtr Grey UTPSP2M3 Mtr Grey UTPSP3M5 Mtr Grey UTPSP5MCAT5E STP with black boots1 Mtr Grey STPC1MBBL2 Mtr Grey STPC2MBBL3 Mtr Grey STPC3MBBL5 Mtr Grey STPC5MBBLCAT6 STP with black boots1 Mtr Grey STPCTG1MBBL2 Mtr Grey STPCTG2MBBL3 Mtr Grey STPCTG3MBBL5 Mtr Grey STPCTG5MBBLWith snagless Pan Plug on each end (seeright).UTP leads are available in 6 colours:Add suffix BL (Black), BU (blue), GR(Green), RD (Red), YL (Yellow), VL (violet)and OR (Orange).Example UTPCH1MBU = Blue.STP leads are available with differentcolour boots on grey cable. Substitute theBL on the end of the part number withthe required suffix shown above.Cat5e RJ45 UTP PlugCrimp Tool for Cat5e plugWire Prep Tool for Cat5e plugMP588-LCT5-8WPT-8Cat6 RJ45 UTP PlugSP688-LCrimp Tool forCat6 plugMPT5-8Unique tangle free plug latch preventssnags and provides easy release savingtime on frequent moves adds andchanges. The Prep tool arranges wires inthe correct sequence providing an easyway to cut to length.Stripping & TerminationToolsCJST CGJT CJT-XWire Stripping ToolCJSTStrips outer jacket of 4-pair UTP & STPcable.Termination Tool forCJT-XCat5e CJ588 jacks on Page 11.Termination ToolCGJTTermination tool for Cat5e & Cat6modules shown on page 11.Standard Fibre KitFJKITGIncludes all tools and consumablesnecessary for termination of multimodeOpti-Jack connectors, multimode ST, SCand FC connectors.Consumables kitFJMKITContains all consumables from theFJKITG kit shown above.Opti-Jack Crimp KitFMKITIncludes all tools and consumablesfor termination of multimodeOpti-Jack Pre-Polished, mechanicalcrimp connector.Primer (50ml)FJPMRAnaerobic Adhesive (10ml) FJPXYBoth Primer and adhesive required forfibre termination.UTP and STP CableFibre-Optic Patch CordsPanduit Fibre-Optic patch cords availableto order. SC, ST, MTRJ, FC, LC and Optijackconnectors on Multimode orSinglemode fibre.Fibre ST & SC ConnectorsSC Simplex MultimodeST MultimodeSC Simplex SinglemodeFSCM1BLFSTMABLFSCS1BUST SinglemodeFSTSBUFibre Optic Epoxy and polish connectors.62.5/125, 50/125 multimode have a blackboot while the 9/125 singlemode haveblue.UTP Cat 5e PVCUTP Cat 5e LSOHUTP Cat 6 PVCUTP Cat 6 LSOHFTP Cat 5e PVCFTP Cat 5e LSOHFTP Cat 6 PVCPUC5504LG-EPUL5504DG-EPUC6004LG-EPUL6004DG-EPFC5504LG-EPFL5504DG-EPFC6004LG-EDFTP Cat 6 LSOHPFL6004DG-EDFor project use when a single brandPanduit end to end solution is requiredSupplied in 305Mtr boxes.16Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Panduit Structured Cabling SystemCat5e 110 Pan-PunchSystemT70 Trunking (plastic case)T70 Faceplates & PowerModules300 Pair Tower P110KT3004Includes all components required900 Pair Tower P110KT9004Includes all components requiredRivet Installation ToolP110RT5-Pair Punch-Down Tool. PDT110MPAN-PUNCH 110 Tower systems providea complete, high density cross-connectsystem with built in cable management.These wall mounted tower systemsinclude jumper troughs and wiring blocksrequired to complete each 25 pair strip.Lables are included. The jumper troughsprovide cable management for patchcords and their exclusive rounded cornershelp maintain cable bend radiusrequirements. CAT6 110 system alsoavailable, please call our sales office fordetails.110 CAT5e Connectors &Patch Cables110 Field Terminable CAT5eConnectors1 Pair 110 Conector P110PC1-X2 Pair 110 Conector P110PC2-X3 Pair 110 Contector P110PC3-X4 Pair 110 Contector P110PC4-XFeatures a clear cap to ensure correct wiresequence and connection orientation.Connectors are field terminable.110 CAT5e Patch Cables1 Mtr P110PC4IG1M2 Mtr P110PC4IG2M3 Mtr P110PC4IG3M5 Mtr P110PC4IG5M4 Pair Cable Assemblies with 110connectors on each end.CAT6 110 system also available. Pleasecall our office.3 Mtr Trunking BaseSingleT70BAW3TwinT702BAW-33Mtr Trunking CoverSingleT70CAW3TwinT702CAW-3Trunking DividerSingleT70DW3TwinT70DAW-3Base Coupler FittingSingleT70BCAW-XTwinT702BCAW-XCover Coupler FittingSingleT70CCAW-XTwinT702CCAW-XInside Corner FittingSingleT70ICAWTwinT702ICAWOutside Corner FittingSingleT70OCAWTwinT702OCAWRight Angle FittingSingleT70RAAWTwinT702RAAWTee FittingSingleT70TAWTwinT702TAWEntrance End FittingSingleT70EEAWTwinT702EEAWEnd Cap FittingSingleT70ECAWTwinT702ECAWPanduit T-70 Non-Metallic trunking is alightweight, easy-to-handle and easy toinstall multi-channel raceway.T-70 raceway will not chip, peel, rust orcorrode and its solid colour concealsscratches. Available in singleCompartment design or a twincompartment with two totallyindependent channels maintained. Sold in3mtr lengths, the trunking base and coverare required. Ideal for power, low voltageand fibre optic applications.FaceplatesHorizontal 1 insertHorizontal 2 insertVertical 1 insertT70BH1AWT70BH2AWT70B1AWVertical 2 insertT70B2AWFaceplates snap directly into T70 trunkingand accept shuttered/unshutteredmodules (shown on page 12) whichhouse jacks shown on page 11.Power ModulesUK13 Amp Power ModulePower Module SwitchBlank ModuleEMG13AW-XETG16AW-XEBGAW-X2 Gang Module Plate T70UMBAW-XUk power modules for T70 trunking.The 2 gang plate houses 2 modules,choose from: 2 power, 1 power and 1switch or 1 power and one blank.Fiberrunner & FiberductThe FIBERRUNNER and FIBERDUCTFibre-optic cable routing systemsprovides an integrated routing solutiondesigned to segregate, route and protectfibre-optic and copper cabling to,between and above racks within anequipment room or facility. TheFiberrunner system is available in 2x2, 4x4,6x4 & 12x4 (inches) sizes with theadvantage of hinged covers and theversatility of Multiple spillout options.Fiberduct is available in 2x2 & 4x4sizes (inches) with snap-on covers. Bothsystems are available in yellow or orange.Please phone our sales office for details.2 - STRUCTURED CABLING SYSTEMS (PANDUIT)Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk17

Panduit Structured Cabling SystemDot Matrix Hand HeldPrinterLow-Cost Thermal TransferHand-held PrinterPatch Panel Labels forDesktop PrintersSTRUCTURED CABLING SYSTEMS (PANDUIT) - 2Printer KitLS3E-AUKit Includes: Printer, Battery Pack,Battery Charger, Printer Ribbon, WristStrap and Operators ManualPlug Type: UK 240Replacement RibbonLS3-RIBCarrying CaseLS3-CASEReplacement AC Battery LS3E-CPChargerLightweight, versatile printer for highquality labels that you can print anytime,anywhere.Flexibility to print self-laminating cablelabels, heat shrink labels and networksystem component labels faster thanother hand-held dot-matrix printers.See Labels BelowSelf Laminating Cable LabelsTotal Area (mm)Part No.25.4 W x 31.7 D LWS-2*38.1W x 31.7 D LWS-3*25.4W x 63.5 D LWS-10***250 per pack**100 per packUse the LWS-2 & 3 for 4 pair cables.Use the LWS-10 for 25-50 pair cables.Modular & 110 Patch Panel Labels.Label Size (mm)Part No.31.1W x 8.5D L3CPLFWH*93.5W X 6.3D L3PP2WH***500 per pack**100 per packUse the L3CPLFWH for Panduit Modularpatch panels. Use the L3PP2WH for 110Pre-Configured Panduit Patch Panels.Modular Jack LabellingLabel Size (mm)Part No.34.9 W x 4.8 D (white) L3PJ1WH34.9 W x 4.8 D (clear) L3PJ1CLLabels for use with Panduit Cat5e, Cat6Jacks and Opti-jacks. Available in White(WH) or Clear (CL). 500 Labels per roll.Printer KitPrinter kitLS7Kit Includes: Printer, Battery Pack,Hardside Carrying Case, Wrist StrapOperators Manual, Black/White CassetteSeparator tool, 6 AA alkaline batteries.Cleaning CassetteCleaning cassetteLS7-CLNThe LS7 palm-sized printer is packed withbenefits that make it the ideal solutionfor on-site network connectivity labelling.The high quality thermal transfer headproduces professional looking labels thatwon't smear. This affordable printerminimizes waste and makes patch panel,faceplate and cable marking effortless.Label for Patch PanelsBlack/White LabelsBlack/Clear Labels(6mm width x 8Mtrs length).Labels for faceplatesBlack/White LabelsBlack/Clear Labels(9mm width x 8Mtrs length).Labels for pathways, rack spacesBlack/White LabelsBlack/Clear Labels(12mm width x 8Mtrs length).Labels for cables, pathways, racksBlack/YellowBlack/Red(18mm width x 5Mtrs length).Ultimate ID Labels.LS7-25-1LS7-25-2LS7-38-1LS7-38-2LS7-50-1LS7-50-2LS7-75-5LS7-75-6Black/White LabelsUILS7BWUltimate ID Labels for Patch panels,faceplates / surface mount boxes &marker ties(6mm width x 8Mtrs length).Label cassettes includes both labelmaterial and ribbon.WhiteBlueGreenYellowCPPLF-5CPPLF-5BUCPPLF-5GRCPPLF-5YLRedCPPLF-5RDLaser and Dot-Matrix Labels for Panduitmodular and punch-down patch panelsLabel size is 15.5mm X 8.4mm.5000 Labels per pack.Hook & Loop Cable TiesHLC SeriesHLT SeriesHLS SeriesHLT Series (Hook & Loop) Black pack of 10203 mm L x 12.7 mm W HLT21-XO305 mm L x 12.7mm W HLT31-XOHLC Series (With Clinch ring) Black pack of 10305 mm L x 19.1 mm W HLC3S-XO457 mm L x 19.1 mm W HLC5S-XOHLS Series (in Roll Form) Black cut to lemgth4572 mm L x 19 mm W HLS-15ROHLS Series (Perforated 10 ties to a roll) Black305 mm L x 19 mm W HLS3S-XO457 mm L x 19 mm W HLS5S-XOEasy to release and re-use. Ideal forcopper and fibre optic cables. Alsoavailable in a range of colours.18Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Panduit Panview Intelligent Patching SystemNetwork reliability, Security and EfficiencyStructured cabling is the foundation of your network, and patch fields are the heart of your structured cabling system.A single patch cord disconnection can bring critical segments of the network down, provide an unimpeded source for a breachin network security or decrease the efficiency of the network exponentially. Without an on-line physical layer managementsystem, those same patch fields are virtually invisible in your network management system. The Panduit PANVIEW system,through its innovative use of Panview software, master and satellite scanners and enabled patch panels, provides complete endto end physical layer management.PanView provides real-time information on the state of the connections in the network. If a patch cord is disconnected, aninstantaneous alert message is displayed at the management station. Panview continually scans the network and updates it'sdatabase to ensure the patch fields are 100% accurate.ApplicationsMission critical network connection where extended downtime can mean the life or death of an organisation. Systems with highsecurity requirements, when knowing who is connected and where they are connected is critical. Networks with high customerturnover when knowing which customer your technicians are doing work for and how much time to allocate back to eachcustomer is important.Cost EffectiveIf budgetary constraints mean a fully intelligent patching system can not be implemented in one go, Panview is the idealsolution.Because the PanView system is modular once the patch panels have been installed, the additional parts of the system can beadded at a later date when the budget allows.EfficiencyResponding quickly and efficiently to user requests for service changes is often a challenge. Network administrators andtechnician spend significant amounts of time planning and executing the process. Even then mistakes happen. The wrong patchcord is accidentally disconnected or the right cord ends up in the wrong port causing even greater confusion. The PanViewsystem eliminates this problem with two software modules, the Link Module and the Work Order Module.Link ModuleThe Link Module allows the administrator to graphically view the entire link from the management station. It will also allow forchanges to be made to any link in the system with just a few clicks of the mouse button.Work Order ModuleWith the work Order Module, the network administrator can plan,prioritise, and assign all of the moves, additions and changes in thesystem.PanView then documents the status of the work order, guides thetechnician through the changes using LEDs on the patch panels,records the time needed to complete the task, and automaticallyupdates the database to reflect the new configuration.System Components1. SOFTWAREPanView Core Software sits at the heart of the system and with theadditional modules can generate work orders, check system utilization and monitor conectivity.2. PANVIEW SCANNERSThese electronic scanners are the connectivity data collectors of the PanView System. The scanners monitor on-site patch panelconnectivity, and provide real-time information on the status of all network connections. Each Master scanner can support 7satellite scanners and provide the interface for the PANview workstation.3. ENABLED CATEGORY 6 PATCH PANELSThe Panview patch panels perform two functions in the comms room. The primary function is to transfer data around thenetwork, however with the additional circuit board they become an integral component in the PanView system. Each panel hasLEDs above each RJ45 port which via the PanView software can be used to indicate which patch leads need to be moved. Oncemoved the patching database is updated.2 - STRUCTURED CABLING SYSTEMS (PANDUIT)For more details and a demonstration of the Panduit PanView system please contact the sales office.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk 19

Nexans Structured Cabling SystemCat5e "Essential" UTPpunchdown jackFibre modules forwallplatesSTRUCTURED CABLING SYSTEMS (NEXANS) - 2The Nexans (formerly Alcatel) structuredcabling range includes:LANmark 5 & LANmark 6 are CAT5e &CAT6 systems based around tool-less jacksthat snap into modular patch panels &wallplates. Allows fast and reliabletermination without punch down tools.Comfortably exceeds the headroomrequirements of the respective CAT5e &CAT6 standards. 20 year system warrantycovering parts & labour if installed by aNexans partner. Essential is a low costCAT5e punchdown system compatiblewith industry std 110 or LSA Kronetooling. A 15 year ‘Link Certificate’ maybe easily downloaded from the Nexanswebsite by any installer using the‘Essential’ system at a customer site.See www.nexans.co.ukCAT5e & CAT6 tool-less"Lanmark" jacksCat5e UTP "Essential" punchdownKrone/110 compatible jack 420.416Low cost jack snaps into flat & angledmodules (below), LJ6C modules (right)and modular panels on the next page.Frames & blanksSingle gang frame 424.013Double gang frame 424.02325x50mm half blank 424.10312.5x50mm quarter blank 424.003Brushed steel or brass frames on page30.Angled housig to acceptModules below 422.003M/mode module withtwo ST couplers 420.022M/mode module with1 SC duplex coupler 420.032ST or SC modules must be used withangled housing then snapped into frames(left).LJ6C modules for trunking& floor boxesUTP jackComfort ToolFTP jackModules to accept jacksflat shutteredangled shutteredand clipLJ6C flat shuttered 424.213*LJ6C angled shuttered withlabel window (must be usedwith keystone clip below) 424.203*Keystone clip 429.620Must be used with angled LJ6C module orsnap in jacks will not fit. Accepts LANmarkand Essential jacks.Cat5e UTP "LANmark5"tool-less jack 420.51012 way Zone DistributionBoxCat5e FTP "LANmark5"tool-less jack 420.530Cat6 UTP "LANmark6"tool-less jack 420.615twin shuttered angledCat6 FTP "LANmark6"tool-less jack 420.635For faster installation of medium/largequantities of "LANmark" jacks usethe hand held comfort tool 420.695Tool-less jack enables all eight wires to beterminated quickly without the need forpunchdown tooling and without havingto untwist the cable pairs.Used with the frames & modules (right),LJ6C modules (right) & modular panels onthe next page.25x50mm flat shuttered 424.11325x50mm angled shuttered* 424.204*Keystone clip (Must be used with25x50 angled shuttered module orsnap in jacks will not fit). 429.620Twin shuttered angled withlabel window 423.540USingle gang frame accepts two 25x50mmmodules/1 twin angled. Double gangframe accepts 4 25x50 modules/2 twinshuttered.521.600Designed for the installation of aconsolidation point. 12 ports, back andbottom entry, tie wrap holes to fix cable.Screen printing service available.20Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Nexans Structured Cabling SystemCAT5e UTP "Essential"punch down patch panels24 way UTP 1U with Krone/110compatible punchdown 500.20224 way UTP 1U with Krone compatiblepunchdown & rear cable management.500.201"Essential" panels are Nexans low costrange. They have numbered ports & aresupplied with cage nuts.Modular patch panel withsliding mechanism & rearcable management.Modular patch panel withrear cable management24 port 1U 521.661Accepts "LANmark" 5 & 6 snap in jacks &"Essential" jacks. Spring finger rear cablemngmnt holds cable without the need forcable ties.Numbered ports with cage nuts. Panel issupplied with shuttered ports. The plasticshutters are snapped on/off so can beeasily removed if not required.CAT5e UTP "LANmark5"punch down patch panelswith sliding mechanismCAT5e FTP "LANmark5"punch down patch panelswith sliding mechanism24 way FTP 1U with LSA+punchdown & rear cablemanagement. 500.111LSA+ punchdown tool 102.107Panels have a top cover & the samesliding mechanism described bottom lefton modular panels and shown above.With slide out label strips numbered 1-120and labels marked for voice/data. Cagenuts included.2 - STRUCTURED CABLING SYSTEMS NEXANS)50 position 1U Voice Panel24 port 1U 521.663Accepts "LANmark" 5 & 6 snap in jacks &"Essential" jacks. A mechanism allows thefront & base of the panel to slide out &drop down by approximately 45 degrees(as shown top right). This enablesengineers to position the cable at theback of the panel (secured by strain reliefspring fingers), & terminate from thefront while the panel is rack mounted.Panel is supplied with shuttered ports.The plastic shutters are snapped on/off socan be easily removed if not required.With slide out label strip and cage nuts.24 way UTP 1U with LSA+ punchdown& rear cable management 500.101LSA+ punchdown tool 102.107These panels have a top cover & the samesliding mechanism described to the left(as shown top right). With slide out labelstrips numbered 1-120 and labels markedfor voice/data. Cage nuts included.Blanks for modular panels50 position 1U Voice Panel 500.350Compatible with LSA Krone/110 tooling.Numbered ports. With rear cablemngmnt. Supplied with cage nuts.Fibre panelsPack of 24 420.6501U empty fibre panelfor 24 ST couplers 441.2011U empty fibre panelfor 12 SC Duplex couplers 441.202ST Multimode coupler 205.123SC duplex Multimodecoupler 205.127Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk21

Nexans Structured Cabling SystemCAT5e & CAT6 patch leadsCAT5e & CAT6 solid cableSTRUCTURED CABLING SYSTEMS (NEXANS) - 2Horizontal hook cablemanagement1U 5 hook 102.105Horizontal 19" hook cable tidy panels area cost effective way of managing patchcables.Horizontal cable mngmntwith clip on cover1U 102.1172U with large bend radius 102.127With slots top & bottom for patchcables. Clip on cover allows easy access.Blank Plate1U Blank plate 109.207Horizontal 19" filler panel reserves rackspace for future use and helps keepinstallations manageable by acting as adivider between devices.Fibre cableFor Nexans fibre cable see page 42.Essential LANmark 5LANmark 6CAT5e "Essential" UTP1.5Mtr grey3Mtr greyCAT5e "LANmark 5"UTP CAT5e 1Mtr greyUTP CAT5e 2Mtr greyUTP CAT5e 3Mtr greyUTP CAT5e 5Mtr greyFTP CAT5e 1Mtr greyFTP CAT5e 2Mtr greyFTP CAT5e 3Mtr greyFTP CAT5e 5Mtr greyCAT6 "LANmark 6"UTP CAT6 1Mtr greyUTP CAT6 1Mtr LSOH orangeUTP CAT6 2Mtr greyUTP CAT6 2Mtr LSOH orangeUTP CAT6 3Mtr greyUTP CAT6 3Mtr LSOH orangeUTP CAT6 5Mtr greyUTP CAT6 5Mtr LSOH orangeFTP CAT6 1Mtr LSOH orangeFTP CAT6 2Mtr LSOH orangeFTP CAT6 3Mtr LSOH orange101.112DG101.112FG101.113CF101.113EF101.113FF101.113HF101.123CF101.123EF101.123FF101.123HF101.214CF101.214CO101.214EF101.214EO101.214FF101.214FO101.214HF101.214HO101.224CO101.224EO101.224FOFTP CAT6 5Mtr LSOH orange 101.224HOAll the above patch leads have blackstrain relief boots. "Essential" patch leadsare low cost for use with the ""Essential"15 year warranty. LANmark patch leadsare for use with the LANmark 20 yearwarranty programme.For details see the top of page 20.CAT 7 system"Essential" CAT5e 100Mhz cableCAT5e UTP PVC grey 100.561CAT5e UTP LSOH orange 100.551CAT5e FTP PVC grey 100.461CAT5e FTP LSOH orange 100.451"LANmark5" CAT5e 350Mhz cableCAT5e UTP PVC grey 100.517CAT5e UTP LSOH orange 100.507CAT5e F2TP PVC grey 100.431CAT5e F2TP LSOH orange 100.421"LANmark6" CAT6 cableCAT6 UTP PVC grey 100.617CAT6 UTP LSOH orange 100.607CAT6 F2TP PVC grey 100.661CAT6 F2TP LSOH orange 100.662All in 305Mtr boxes except for the F2TPCAT5e & CAT6 versions which is on 500metre reels. F2TP has a dual foil shield.Quick Mount 42U Cabinet42U 800(W)x800(D) Cabinet 340.001Roof mount fan 203.171Shelf with 4 fixing points 303.163Shelf with 2 fixing points 303.162Sliding shelf 303.164Plinth (100mm high) 340.185Set of 8 patching ringsfor fixing to uprights 343.206Baying kit 330.102Fast assembly flat pack cabinet may beassembled by 1 person in about 20minutes Lockable front door & tintedsafety glass. Inside opening system forside panels.The Nexans GG45 system operates at 600Mhz & is backward compatible withCAT5e & CAT6. Contact our sales dept fordetails.22Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Hubbell Structured Cabling SystemCAT5e STP jackOne piece wallplatesFounded more than a hundred years agoHubbell today is a worlwide companyemploying over 8,000 people with annualsales of over $1.4 billion.Systems are available in CAT5e and CAT6110 punchdown with either modular orfixed PCB patch panels. Hubbell'sinnovative RJ45 jack design and "1punch" tooling ensures very fasttermination times.This very competitively priced systemis available with a 25 year systemwarranty when installed by a Hubbellpartner.See www.hubbell-premise.comCAT5e & CAT6 "Xcelerator"UTP 110 jacksCAT5e UTP jacksBlack CAT5e UTPWhite CAT5e UTPBlue CAT5e UTPRed CAT5e UTPYellow CAT5e UTPOrange CAT5e UTPGreen CAT5e UTPHXJSC5EBKHXJSC5EOWHXJ5EB25HXJ5ER25HXJ5EY25HXJ5EO25HXJ5EGN25HSJ5EFor use in Hubbell wall plates and surfaceboxes. Compatible with Krone LSA and110 punch down tools.Frames & BlanksSingle gang flat frameSingle gang bevelled frameDouble gang flat frameDouble gang bevelled frame50x12.5mm quarter blankEMBP1EBM1EMBP2EBM2EMB1250x25mm half blankEMB25Single gang frame accept 2 modules,double gang accepts 4 modules. (Seebelow).Modules to accept jacksSingle gang single shutteredLJU6C module for floor box& trunking applicationsLJU6C 37x23.5mm shuttered modulefor floor boxes/trunkingEM6SModule accepts UTP & STP jacks. See"Sharpmark" labelling system on page 35.Advanced multimediaoutletBPS11Single gang twin shuttered BPS12Accepts UTP & STP jacks. "Sharpmark"labelling system on page 35.2 - STRUCTURED CABLING SYSTEMS (HUBBELL)CAT6 UTP jacksBlack CAT6 UTPWhite CAT6UTPBlue CAT6 UTPRed CAT6 UTPYellow CAT6 UTPOrange CAT6 UTPHXJ6BK25HXJ6OW25HXJ6B25HXJ6R25HXJ6Y25HXJ6OR25Green CAT6 UTPHXJ6GN25Coloured jacks are in packs of 25.Other colours also available.These jacks are used in Hubbell wallplates/modules, modular panels & surfaceboxes. Jacks allow fast termination timesas the cable pairs do not need to beun-twisted prior to termination.Use 110 punch down tools or Hubbell"1 punch tool" part number TX4P(page 25) which terminates and cuts all 4pairs in one operation.Flat shutteredAngled shuttered2 port angled un-shuttered50x25mm flat shutteredEM1S(Snaps into above frames)50x25mm angled shuttered EAM1S(Snaps into above frames)50x50mm 2 port angled un-shuttered(Snaps into above frames) EAMW2Modules accept UTP & STP jacks. Used inframes shown above. "Sharpmark"labelling system on page 35.Outlet shown loaded with various couplersSurface mount boxSC bracket with 1 duplexmm/sm couplerST bracket with 2 mm/smcouplersLC bracket with quad couplerAMO12AMOBSCDAMOBST2AMOLCQBlank bracket (bag of 10) AMOBL10Unloaded bracket to acceptone UTP jack (bag of 10) AMOBJ10Unloaded bracket to accepttwo UTP jacks (bag of 10) AMOB2J10Accepts 6 brackets for up to 12 copper or12/24 fibre connections or a mixture ofboth.Screen printing service available.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk23

Hubbell Structured Cabling System"SpeedChannel" CAT5e UTP110 Punchdown panels"NextSpeed" CAT6 UTP 110Punchdown panels100Base-T Telco panelsSTRUCTURED CABLING SYSTEMS (HUBBELL) - 224 position 1U PSC5E2448 position 2U PSC5E48Rear cable mngnt barPCBLMGTLow cost 110 punch down panels withnumbered ports. Rigid design eliminatesflex during punch down. Tooling onpage 33."SpeedGain" CAT5e UTP110 Punchdown panels16 position 1U P5E16B19E24 position 1U P5E24B19E32 position 2U P5E32B19E48 position 2U P5E48B19ERear cable mngnt barPCBLMGT110 punch down panels with numberedports and label field.A clear plastic shroud protects the PCBfrom errant terminations. Rigid designeliminates flex during punch down.Tooling on page 33.CAT5e STP punchdownpanel24 position 1U P624U48 position 2U P648URear cable mngnt barPCBLMGT110 punch down panels with numberedports. Rigid design eliminates flex duringpunch down. Provides higher band widthto support data in excess of 250Mhz."Xcelerator" modularpanels16 port 1U UDX16E24 port 1U UDX24E36 port 1U ultra high density UDX36E48 port 1U ultra high density UDX48E1U48 port 2U UDX48ERear cable mngnt barPCBLMGTModular panels accept "Xcelerator"CAT5e & CAT6 jacks shown on page 23.The 16 & 24 port 1U & the 48 port 2Upanels have numbered ports. The 36 and48 port ultra high density versions are notnumbered but do provide significantspace savings. These panels also acceptcertain audio, video and fibre modules.Please contact our office for details.24 port 1U 100Mbps MCC24100BT1948 port 2U 100Mbps MCC48100BT1924 port panels have 2 female Telco's and48 ports have 4 female Telco connectors.The panels have been tested to 100Mhz &exceeds category 5 transmissionrequirements. Backward compatible to10Base-T.For Telco leads please contact oursales office.Fibre panels with slidingtrayST fibre panels (1U)With 4 ST couplersWith 8 ST couplersWith 12 ST couplersWith16 ST couplersWith 24 ST couplersSC fibre panels (1U)With 2 duplex SC couplersWith 4 duplex SC couplersWith 6 duplex SC couplersWith 8 duplex SC couplersFEUR04STMFEUR08STMFEUR12STMFEUR16STMFEUR24STMFEUR04SCMFEUR08SCMFEUR12SCMFEUR16SCMWith 12 duplex SC couplers FEUR24SCMHubbell fibre panels are pre loaded withST or SC duplex connectors.With numbered ports and cablemanagement for spooling excess fibre.Sliding tray & 1U height. These panelsrepresent excellent value.Sharpmark labelling system on page 35.SHDP5E24B19EShielded panel with numbered ports.Compatible with 110 & Krone tooling.With ground wire, metal cover & cagenuts.Tooling on page 33.24Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Hubbell Structured Cabling SystemHorizontal 1U cablemanagement with D rings"Nextframe" 45U rack"2Quick" ST & SC Fibrecrimp connectorsWith 4 D ringsMCCMP1UHorizontal enhanced cablemanagementFront managementFront management with hinged coverShown with optional horizontalmanagement (see left)CR197645U rack with 6" wide side cable mngmntchannels and covers. Provides rollededges to maintain bend radious, passthrough holes and slots for tying offcables along the length of the channel.For suitable horizontal management seethe enhanced management shown left."1 - Punch" 110 toolSC connectorST connectorST connector (pack of 12)Crimp ToolFCSTMQ12SC connector (pack of 12) FCSCMQ12Crimp tool with die set for 2QuickST & SC connectorsOFCMT04Multimode connectors for tight buffered62.5/125 fibre cable.Simply crimp the connector then cleavethe fibre and polish the ferrule tip toproduce a premium quality fibreconnection. No epoxy, adhesives or curingovens required. See pages 48-49 for fibreconsumables.2 - STRUCTURED CABLING SYSTEMS (HUBBELL)Front/rear management + hinged coversFront management with 7 ringsSC, ST & LC fibre couplers1U (3.5" depth rings)2U (3.5" depth rings)2U (6.0" depth rings)HC119ME3NHC219ME3NHC219ME6NFront management with 7 rings andhinged cover1U (1.75" depth rings) HC119CE1N2U (3.5" depth rings) HC219CE3NFront & rear management with 7rings and hinged covers1U (3.5" front ring depthand 6.0" rear ring depth) HC119GC362U (3.5" front ring depthand 6.0" rear ring depth) HC219GC36Front/rear hinged covers1U coverHC119C2U coverHC219CAll the above cable management panelshave 7 rings and 6 pass through holes.All steel construction, no plastic parts towear or break.1-Punch tool with head,blades & Snap-EXtermination aid.Additional Snap-Ex aidTX4PHXTP"Jack Knuckles" termination aid. HXTA1-Punch tool terminates "Xcelerator"jacks (shown on page 23) in one punch &cuts off the excess wire.The "jack Knuckles" termination aidassists in lacing & terminating the jack.Ergonomic tool is supplied with a handstrap and may be used for left or righthanded terminations.SCLC quadSC duplex coupler (blue)ST couplerSTFASCMPB6FEASTMPBLC quad adapter (blue) FAQLCMPB6Suitable for single mode or multi modeapplications. The SC and LC couplers arein packs of 6.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk25

Hubbell Structured Cabling SystemY AdaptersCAT5e UTP patch leads withstrain relief boots"ReBox" wall cabinetSTRUCTURED CABLING SYSTEMS (HUBBELL) - 2Converts a T568B wired RJ45jack to two 10Base-T wiredjacks. Pairs 2 & 3 are split tojack (1) & pairs 1 & 4 are splitto jack (2)BR851DConverts a T568B wired RJ45jack by splitting pairs 1 & 4 to avoice wired application 8 wayjack (1) & pairs 2 & 3 to a10Base-T wired 8 positionjack (2).BR851ADesigned to connect two piecesof voice, data or ancillaryequipment to a USOC RJ61 eightposition jack. Pairs 1 & 2 are splitto the centre position of jack (1),& pairs 3 & 4 are split to centreposition of jack (2).BR851241UDesigned to connect two piecesof voice, data or ancillaryequipment to a T568B RJ45 jack.Converts a T568B wired RJ45jack into two 2-pair jacks. Pairs 1& 2 are split to the centre positionsof jack (1), & pairs 3 & 4 are splitto the centre positions ofjack (2).BR851241AConverts a T568B wired RJ45jack by splitting pairs 1, 2 & 3to 1st 6-positions of jack (1),& pair 4 to positions 4 & 5 ofjack (2).BR851341B3ft (0.91Mtrs)6ft (1.83Mtrs)10ft (3.05Mtrs)PC5EP*03PC5EP*06PC5EP*1016ft (4.88Mtrs)PC5EP*16* Substitute with the required colourcode.G = Grey, B = Blue, Y = Yellow, BK = BlackR = Red, GN = Green, OR = Orange,W = White. e.g. PC5EPY06 = Yellow 6ftMinimum order quantity or lead timesmay apply to certain colours.Hubbell patch leads are manufacturedwith a tightly controled terminationprocess and are 100% tested for NEXT, RL,attenuation, & ELFEXT (pair to pair) toensure optimum performance.CAT6 UTP patch leads withstrain relief bootsAccepts 2 switches & 2 panelsOther Hubbell productsRE2Accepts 5 switches & 4 panels RE4Secure cabinet for the remote positioningof network equipment. Ideal forclassrooms, warehouses and retail outlets.* Metal with grey powder coat finish.* Acceps patch panels & Hubs/Switches.* Cable entry knockouts side, bottom &top.* Lift off reversible door.* Engineered airflow to prolong the lifeof active equipment.* RE2 & RE4 both accept hubs/switcheswith a maximum depth of 14.5 inches.* Dimensions:RE2: 818H x 615W x 178DRE4: 818H x 615W x 254DBR851DBR851241UBR851341BBR851ABR851241A3ft (0.91Mtrs)6ft (1.83Mtrs)10ft (3.05Mtrs)PCX6*03PCX6*06PCX6*1016ft (4.88Mtrs)PCX6*16* Substitute with the required colourcode.GY = Grey, BK = Black, B = Blue,Y = Yellow, OR = Orange, GN = Green,P = Purple, W = White.e.g. PCX6B06 = BlueMinimum order quantity or lead timesmay apply to certain colours.Each PCX patch lead is 100% performancetested to ANSI/EIA category 6 patch cordspecifications.The Hubbell range is vast and alsoincludes:* 110 CAT5e & CAT6 tower systems andaccessories.* Raceway* Fibre products* Labelling productsPlease ask for the latest Hubbellcatalogue.See www.hubbell-premise.com26Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

CAT5e & CAT6 Cable"Mini5/6" CAT5e & CAT6patch cable"Nexans" CAT5e & CAT6solid cableLow cost CAT5e & CAT6 cable offers highperformance & exceptional value formoney. Approved for use in the Mini5CAT5e 15 year system warranty or Mini6CAT6 25 year system warranty wheninstalled by an approved partner.Belden have long been recognised as aninternational leader and innovator incable products. Their CAT5e and CAT6cable is approved for use in the Panduitand Hubbell 25 year system warrantyprogrammes.Extensive range of CAT5e & CAT6 cable.Nexans are a world leader in the designand manufacture of LAN cable. Usedwith the Nexans twenty year systemwarranty when installed by an approvedpartner.Cat5e and CAT6 cable for use with thePanduit structured cabling system when acomplete end to end single brandsolution is required. 25 year systemwarranty if installed by an approvedPanduit partner."Mini5/6" CAT5e & CAT6solid cable (305Mtr boxes)"Mini5" CAT5e UTP 100Mhz (305Mtrboxes).Grey PVC patchGrey LSOH patchRed PVC patchBlue PVC patchGreen PVC patchYellow PVC patchBlack PVC patchUTP4W5PBUTP4W5PB-LSUTP4W5PB-RDUTP4W5PB-BEUTP4W5PB-GNUTP4W5PB-YWUTP4W5PB-BKPink PVC patchUTP4W5PB-PK"Mini5" CAT5e UTP 350Mhz (500Mtrreels).Grey PVC patchRed PVC patchBlue PVC patchGreen PVC patchYellow PVC patchUTP4W5PREUTP4W5PRE-RDUTP4W5PRE-BEUTP4W5PRE-GNUTP4W5RE-YWBlack PVC patchUTP4W5PRE-BK"Mini5" CAT5e FTP 100Mhz (305Mtrboxes).Grey LSOH patchFTP4W5PB-LSBlue PVC patchRed PVC patch"Mini6" CAT6 UTP (305Mtr Box)Grey PVC patchFTP4W5PB-BEFTP4W5PB-RDUTP4W6PB."Belden" CAT5e & CAT6solid cable (305Mtr boxes)"Essential" CAT5e 100Mhz cableCAT5e UTP PVC grey 100.561CAT5e UTP LSOH orange 100.551CAT5e FTP PVC grey 100.461CAT5e FTP LSOH orange 100.451"LANmark5" CAT5e 350Mhz cableCAT5e UTP PVC grey 100.517CAT5e UTP LSOH orange 100.507CAT5e F2TP PVC grey 100.431CAT5e F2TP LSOH orange 100.421"LANmark6" CAT6 cableCAT6 UTP PVC grey 100.617CAT6 UTP LSOH orange 100.607CAT6 F2TP PVC grey 100.661CAT6 F2TP LSOH orange 100.662All in 305Mtr boxes except for the F2TPCAT5e & CAT6 versions which is on 500Mtrreels. F2TP cable has a dual foil shield.Essential cable is used as part of Nexan's15 year system warranty covering parts."LANmark" cable is used in the 20 yearsystem warranty programme coveringparts & labour. See the Nexans system onpages 20-22."Panduit" CAT5e & CAT6solid cable2 - STRUCTURED CABLING SYSTEMS (CABLE)"Mini5" CAT5e (305Mtr boxes)UTP grey PVCUTP4M5SBUTP blue PVC (350Mhz)UTP purple LSOHFTP grey LSOH"Mini6" CAT6 (305Mtr boxes)UTP grey PVCUTP4W5SBEUTP4M5SB-LSFTP4W5SB-LSUTP4W6SBUTP grey LSOHUTP4W6SB-LSPVC or LSOH (Low smoke zero halogen)jacket. Metre markings on cable todetermine how much is left in a part usedbox. UTP is unshielded, FTP has a foilshield.CAT5e UTP grey PVCCAT5e UTP blue PVCCAT5e UTP grey LSOHCAT6 UTP grey PVC1583E1583E-BLUE1583ENH7812ECAT6 UTP grey LSOH7812ENHShielded cable also available, pleasecontact our sales office. CAT6 cable hasbonded pairs for uniform conductor toconductor spacing & core twist along thelength of the cable providing improvedpeformance.When terminating CAT6 use cable pairseparation tool 1798A.CAT5e UTP PVC greyCAT5e UTP LSOH dark greyCAT5e FTP PVC greyCAT5e FTP LSOH dark greyCAT6 UTP PVC greyCAT6 UTP LSOH dark greyCAT6 FTP PVC greyPUC5504LG-EPUL5504DG-EPFC5504LG-EPFL5504DG-EPUC6004LG-EPUL6004DG-EPFC6004LG-EDCAT6 FTP LSOH dark grey PFL6004DG-EDAll in 305Mtr boxes except for CAT6 FTPwhich is on 500Mtr reels. Supplied to orderwhen a complete Panduit single brandsolution is required.See the Panduit system on pages 11-19.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk27

Cable & Cable TiesExternal CAT5e solid cableCW1308 & CW1308B cable"Mini5" hook & loop cabletiesSTRUCTURED CABLING SYSTEMS (CABLE & CABLE TIES) - 2UTP4R5SB-EXTExternal CAT5e solid cable in a blackwater resistant polyethylene outersheath. Supplied in 305Mtr boxes.Manufactured by Raydex CDT.CAT5 25 pair LSOH cableUTP25W5SR-LSOEOrange low smoke zero halogen cablemanufactured by Nexans (formerlyAlcatel). Supplied on reels and cut to yourrequired length.Thin ethernet (10Base-2)coaxial cableCW1308 indoor cable (white PVC)2 pair CW1308 100Mtr reel CW1308-0043 pair CW1308 100Mtr reel CW1308-0064 pair CW1308 100Mtr reel CW1308-0085 pair CW1308 100Mtr reel CW1308-0106 pair CW1308 100Mtr reel CW1308-01210 pair CW1308 100Mtr reel CW1308-02010 pair + earth CW1308 100Mtr reelCW1308-020E25 pair + earth CW1308* CW1308-050E50 pair CW1308* CW1308-100100 pair + earth LSOHCW1308*CW1308-200EGYLSCW1308B indoor/outdoor (Black)10 pair + earth CW1308B* CW1308B-020E20 pair + earth CW1308B* CW1308B-040E25 pair + earth CW1308B* CW1308B-050E50 pair + earth CW1308B* CW1308B-100E100 pair+earth CW1308B* CW1308B-200E* Signifies cable is cut to required lengthand supplied on reels."Panduit"’hook &loop/clinch ring’ tiesHLCClinch ringHLTHook & loop225mm length black225mm length blue325mm length blackMTVT-225BKMTVT-225BEMTVT-325BK325mm length blueMTVT-325BEHook and loop design with a 5mmdiameter hole for screw or rivet fixing.12mm wide and 3mm thick. Supplied inpacks of ten. Re-useable & do notdamage fibre/copper cable. Other coloursavailable to order."Mini5" Nylon cable ties100mm length x 2.5mm wide142mm length x 3.2mm wide203mm length x 3.2mm wideNT100*NT142*NT203*292mm length x 3.6mm wide NT292**Add B to the end of the part numberfor black or N for natural. Supplied inpacks of 1000. Self locking nonreleasable. Flame retardent UL94V-2.ECC01-350ohm impedance coaxial cable for thinwire ethernet applications. Equivelant toBelden 9907. Supplied on reels of 305Mtr.HLSRolls"Mille-Tie" cable tiesHook and loop style (pack of 10)Fibre cable203mm length x 12.7mm wide305mm length x 12.7mm wideHLT21-XOHLT31-XOClinch ring style (pack of 10)Large range of fibre cable from leadingmanufacturers including Tyco, Nexans,OCC & Belden. See page 42.305mm length x 19.1mm wide HLC3S-XO457mm length x 19.1mm wide HLC5S-XOPerforated rolls (10 ties per roll)305mm length x 19.1mm wide457mm length x 19.1mm wideHLS3S-XOHLS5S-XO4.5Mtr roll (Ties may be cut to length)4572mm length x 19mm wide HLS-15ROThe above ties are black. Other coloursare also available. Please contact our salesoffice. Re-useable and do not damagecopper or fibre cable.`Black 305mm lengthNT-100MILNatural LSOH 305mm length BK-100MILReleasable re-useable ties. Once latchedthe cut off tail becomes another tie. Theadjustable latch allows a firm gripwithout pinch or crush. Can be used tosuspend cable or to bind multiplebundles with just one tie. One tie canbundle cable & secure it to a frameeliminating the need for 2 ties. Suppliedin packs of 100.28Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

CAT5E & CAT6 Patch LeadsMini5 CAT5e UTP patchleads with moulded bootsMini5 CAT5e STP patch leadswith moulded bootsMini6 CAT6 UTP patchleads with moulded bootsLength 100Mhz 350Mhz0.5Mtr PCTB5005* PCTM5005E*1Mtr PCTB5010* PCTM5010E*1.5Mtr PCTB5015* PCTM5015E*2Mtr PCTB5020* PCTM5020E*3Mtr PCTB5030* PCTM5030E*5Mtr PCTB5050* PCTM5050E*10Mtr PCTB5100* PCTM5100E**For coloured patch leads add thefollowing suffix:Blue = BE, Red =RD, Green = GN,Yellow = YW, Black = BK,Pink = PK, Orange = OE.No suffix required for grey.Example:Red 100Mhz 2Mtr = PCTB5020RD100Mhz or 350Mhz versions. 350Mhzleads should be used with the Mini5 15year system warranty programme inregistered installations. The boots aremoulded flush to the side of the RJ45plugs to ensure that they can beconnected to any RJ45 socket0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM5005ESPCTM5010ESPCTM5020ESPCTM5030ESPCTM5050ES10Mtr greyPCTM5100ESBoots are moulded flush to the side of theRJ45 plugs to ensure that they can beconnected to any RJ45 socket. STP leadsare 350Mhz & supplied in grey.Crossover patch leads0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM6005PCTM6010PCTM6020PCTM6030PCTM605010Mtr greyPCTM6100Boots are moulded flush to the side of theRJ45 plugs to ensure that they can beconnected to any RJ45 socket. Staggeredinternal contact design on RJ45 plugs.Mini6 CAT6 UTP LSOH patchleads with boots2 - STRUCTURED CABLING SYSTEMS (PATCH LEADS)Mini5 CAT5e UTP 100Mhzpatch leads (non booted)0.5Mtr1Mtr2Mtr3Mtr5MtrPCT5005E*PCT5010E*PCT5020E*PCT5030E*PCT5050E*10MtrPCT5100E**For coloured patch leads add thefollowing suffix:Blue = BE, Red =RD, Green = GN,Yellow = YW, Black = BK. No suffixrequired for grey.Example: Red 2Mtr = PCT5020ERD0.5Mtr1Mtr2Mtr3MtrPCT5005YWBK-XPCT5010YWBK-XPCT5020YWBK-XPCT5030YWBK-X5MtrPCT5050YWBK-XUTP x-over leads are made with yellowcable and a black strain relief boot onone end in order to differentiate themfrom standard patch leads.Wrap around cable labels on page 35.0.5Mtr grey1Mtr grey2Mtr grey3Mtr grey5Mtr greyPCTM6005LSPCTM6010LSPCTM6020LSPCTM6030LSPCTM6050LS10Mtr greyPCTM6100LSLow smoke zero halogen patch leads withslide on RJ45 boots with anti tangleblister. These patch leads should be usedwith the Mini6 25 year system warrantyprogramme in registered installations.Staggered internal contact design onRJ45 plugs.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk29

Structured Cabling AccessoriesBlack boxes (PVC)Mini5 floor boxesCob RJ plugsSTRUCTURED CABLING SYSTEMS (ACCESSORIES) - 2Standard back boxesSingle gang 21mm deepSingle gang 32mm deepSingle gang 45mm deepDouble gang 32mm deepDry lining back boxesSingle gang 35mm deepSingle gang 46mm deepDP1-21PWBDP1-32PWBDP1-45PWBDP2-32PWBDP1-35PWB-DLDP1-46PWB-DLDouble gang 35mm deep DP2-35PWB-DLDouble gang 46mm deep DP2-46PWB-DLDry lining back boxes snap into cavity walls.Brushed steel & brassframes3 compartment floor boxwith 1x twin switched 13 AMPsocket plate 1x blank plate &1 x plate with 4 x LJU6C cut outs. MTFB-34 compartment floor box with2x twin switched 13 AMP socketplates 1x blank plate & 1x platewith 4x LJU6C cut outs.MTFB-4Plates for 3 compartment boxPlate with 2 x 13 AMPswitched socketsMTFB-P13A23Blank platePlate with 4 x LJU6C(37x22mm) cut outsMTFB-PBLA3MTFB-PLJU43Plates for 4 compartment boxPlate with 2 x 13 AMPswitched socketsMTFB-P13A24Blank plateMTFB-PBLA4Plate with 4 x LJU6C (37x22mm)cut outsMTFB-PLJU44Knockouts for conduit/cable entry.Overall dimensions: 310x190x80mm deep.Blank platesRJ45 UTP for round/flat stranded(50 micro ins gold plate) MP8P8C-50RJ45 UTP for round/flat stranded(gold flash plate)MP8P8CRJ45 UTP for round/flat solid orstrandedMP8P8CSOLRJ45 STP for round/flatstrandedMP8P8CSHS4 position 4 contact for flatstrandedMP4P4CRJ11 6 position 4 contact forflat strandedMP6P4CRJ12 6 position 6 contact forflat strandedMP6P6CRJ12 6 position 6 contact forsolid or flat stranded MP6P6CSOLMMP/Dec 6 position 6 contactfor flat solid or stranded MMP6P6CRJ48 10 position 10 contactfor flat strandedMP10P10CFor crimp tooling see page 33.RJ45 strain relief boots forCAT5e plugsBrushed steel single gang MT50-1000BABrushed steel double gang MT50-2000BABrass single gangMT50-1000CABrass double gang MT50-2000CAAccepts 25x50mm modules in the HubbellMini5/6, Nexans & Panduit ranges. Alsoaccepts Nexans twin angle shuttered.AMP RJ plugs (CAT5e, CAT6& RJ12)RJ45 UTP plug 5-554720-2RJ45 UTP Enhanced plug 5-558530-2RJ45 STP plug 5-569530-2RJ45 STP Enhanced plug 5-569552-2RJ45 CAT6 UTPplug 5-1375202-2RJ12 6 position 6 contact 5-555042-3Accept stranded/solid cable except theCAT6 and RJ45 UTP enhanced plugs whichaccepts stranded only. Enhanced plugs are2 part with cable locator.Crimp tools on page 33.Single gangDouble gangDP1-BFPDP2-BFPRJ45 strain relief boots forCAT6 AMP plugsBlack 569875-1Almond 569875-2Red 569875-3Green 569875-4Blue 569875-5Yellow 569875-6Orange 569875-7White 569875-8Violet 569875-9Grey 1-569875-1Minilink AMP Retro-FitColour Minilink AMP Retro-FitLt grey MPSRGY 885006-2 MPCWLGDk grey MPSRDG – MPCWDGBlack MPSRBK 1-885006-2 MPCWBKYellow MPSRYW2-885006-2 MPCWYWGreen MPSRGN 3-885006-2 MPCWGNRed MPSRRD 4-885006-2 MPCWRDBlue MPSRBE 5-885006-2 MPCWBLViolet MPSRVT – MPCWVTWhite MPSRWE – MPCWWEOrange MPSROE – –Retrofit boots may be clipped over RJ45plugs on terminated patch leads. Theabove boots are for use with RJ45UTP/STP and enhanced CAT5e plugs only.Not suitable for use with CAT6 plugs.30Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Structured Cabling AccessoriesRJ11 jack (110 punch down)Mini5 CAT5e UTP TransitionPointRJ45 splittersSVK6C6 position 6 contact jack snaps into Mini525x50mm wallplate modules.Mini5 Couplers & ReducersPanel MountFree hanging couplersRJ45 CAT5e UTP (White)RJ45 CAT4 UTP (Beige)RJ11 6 contact (Beige)Panel mount couplersRJ45 CAT5e UTP (Black)RJ45 CAT5e STPFree HangingReducersFor thru coupler panels see page**.ReducersRJ45FCWE5RJ45FCBERJ11FCBERJ45PCBK5RJ45PCSH5MT50-C5EBFor punching down and joining two endsof CAT5e cable. Dual punchdown blocks.RJ11 - BT adaptersRJ11 skt - 4 way BT plug 30244045RJ11 plug - 4 way BT skt 30244039RJ - D UTP modularadaptersSplits a 4 pair T568A/B jack for10Base-T (Jack 1), & Token Ringor Voice (jack 2)TMODU4Splits a 4 pair T568A/B jack for10Base-T applications ateither end.TMODU5Splits a 4 pair T568A/B jack for1, 2 or 3 pair voice (jack 1) & 1 pairvoice/modem (jack 2)TMODU6Bridges all jack pairs. Compatiblewith any jack wiring. Provides anadditional jack with the samewiring.TMODU7TMODU4TMODU5TMODU6TMODU7RJ45 plug - 2 x RJ45 sockets converts jackstyle functions as a T adapter, or alters thewiring sequence of a modular jack.110mm lead length. Supplied with snapon icons for voice (red), and data (blue).2 - STRUCTURED CABLING SYSTEMS (ACCESSORIES)Reduces mating face of 6 positionRJ12 to RJ11 4 positionRJC64Reduces mating face of 8 positionRJ45 to RJ12 6 position RJC86BKReducer snaps into couplers mating face.RJ45 T adapters3 x RJ45 female RJ45T3F2 RJ45 females - 1 x male RJ458P8CTRJ45 - D9 maleRJ45 - D9 femaleRJ45 - D15 maleRJ45 - D15 femaleRJ45 - D25 maleRJ45 - D25 femaleRJ11 - D9 maleRJ11 - D9 femaleRJ11 - D25 maleRJ11 - D25 femaleDEC/MMJ - D25 maleDEC/MMJ - D25 femaleMale-male jumper leadRJ459M8CTRJ459F8CTRJ4515M8CTRJ4515F8CTRJ4525M8CTRJ4525F8CTRJ119M6CTRJ119F6CTRJ1125M6CTRJ1125F6CTDEC25M6CTDEC25F6CTJLMMFemale-female jumperJLFFWith one piece black hoods. RJ45 versionsare also available with grey hoods. AddGY to the end of the part number.Supplied unconfigured. Jumper leads are90mm long. For Contact insertion/extraction tools see page 34."IBM" style data connectorDC-IBMWith 45 degree & 90 degree cable entry.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk31

Structured Cabling AccessoriesMini5 Data/Voice adaptersBaluns (BNC/Twinax - RJ45)G703 dual BNC - RJ45balunsSTRUCTURED CABLING SYSTEMS (ACCESSORIES) - 2Secondary leadedPABX leadedFull Master leadedISDN leadedDVA-WSECDVA-WPBXDVA-PSTNDVA-ISDNADSL direct plug-inDVAP-ADSLAllows telephone equipment fitted withBT plugs to be connected to an RJ45structured cabling network. RJ45 plugfitted to 150mm lead with a six waytelephone socket in the adapter body,except for the ISDN version which has aRJ45 socket in the body.ADSL version is non leaded.Vanga Data/Voice adaptersLeadedLeaded adaptersCouplerPlug inBNCTwinaxBNC male to RJ45 93ohmwith active pins 4 & 5BM45ABNC male to RJ45 93ohmwith active pins 1 & 2 BM45A12Twinax male to RJ45 105ohmwith active pins 4 & 5TW45ATwinax male to RJ45 105ohmwith active pins 1 & 2TW45A12Minitran's own "Minilink" brand ofbaluns are suitable for IBM 3270, AS400and S3X applications.IBM - RJ45 baluns &adapters10 Base-T Balun (UTP) withactive pins 1&2, 3&6TIBU1236Token Ring Balun (UTP) withactive pins 3&4, 5&6TIBU3456Token Ring Adapter (UTP) withactive pins 3&4, 5&6TIAU3456For integrating equipment with an RJ45interface into the IBM cabling system.Minitran’s own “Minilink” brand.Female BNC (x 2) 75ohm to120 ohm RJ45 socket G703FB-120-2Female BNC (x 2) 75ohm to120 ohm RJ45 socket G703FB-120-1Dual path configuration of the balunallows both the TX & RF coax signals to becarried over a single length of twistedpair cable.Balun panelsA large range of Balun panels with anumber of interface options includingRJ45, BNC, Type 43 and HDC43 isavailable. Please contact our sales officefor details.Surge protectorSecondary leadedPABX leaded3024402E3024402DFull Master leaded 30244021ISDN leaded 30200044Plug in (non leaded) adaptersSecondary plug in3024402APABX plug in 30244029Full Master plug in 30244028ISDN plug in 30200043Composite video BalunPNET1Protects ethernet 10base-T, 100Base-T &Token Ring network interface cards, hubsor LAN equipment.Peak voltage: 6000v.Breakover voltage: 8v peak nominal.Lines protected: 1-8 on RJ45 connector.CouplersSecondary coupler 30244016PABX coupler 30244012Full Master coupler3024400EAllows telephone equipment fitted withBT plugs to be connected to an RJ45structured cabling network. RJ45 plug tosix way telephone socket except for theISDN versions which has an RJ45 socket inthe body. Manufactured by Vanga ofHolland.Pins 4 & 5 activeCVAB45BNC male to RJ45 UTP. Used to connectsurveillance equipment to a structuredwiring system. Provides the interfacebetween 100ohm RJ45 & 75ohm BNC.32Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

CrimpTools & Punch Down Tools"Minilink" RJ plug & BTplug service crimp tools"AMP" fixed die RJ45ratchet tools (For std &CAT6 plugs)Punch down toolsCT05Tooling suitable for:RJ45 UTP/STP plugsCT024 position 4 contact RJ plugs CT03RJ11/12 6P6C/6P4C RJ plugsDEC MMP RJ plugsRJ11/12 6P6C/4C & BT plugsCT04CT07CT3210 Position RJ48 plugs CT11Non ratchet crimp tool for smallproduction runs. Cuts & strips the cable &crimps the plugs shown above."Minilink" RJ plug ratchetcrimp toolsCT17 toolTooling suitable for:CT22/CT23 toolsCob UTP/STP RJ45 PlugsCT17RJ11/12 6 position 6/4 contact,DEC MMP, AMP RJ45 & 10position RJ48 plugsCT224 position 4 contact, RJ11/126 position 6/4 contact, DECMMP & Cob RJ45 plugsCT23Medium duty ratchet tools for lightproduction work and occasional useage.Ratchet ensures constant quality crimps.The CT22 & CT23 tools have multiplepositions in the tool head toaccommodate different plug styles.For std AMP RJ45 plugs 734218-3*For CAT6 AMPRJ45 plug 790163-1* 734218-3 is for std AMP RJ45 plugs only.*For AMP enhanced plug tooling see“Interchangeable die” tool below. Ratchetensures constant quality crimps."AMP" interchangeable dieratchet RJ toolTool without die sets 2-231652-0Tool with RJ45 die set forStandard plug 2-231652-1Die set for RJ11/12 4 &6 position plugs 853400-8Die set for DEC/MMP plugs 853400-6Die set for std RJ45 plugs 853400-1Die set for enhancedRJ45 plugs 1- 853400-0Tool cuts, strips & crimps. The ratchetensures constant quality crimps."Panduit" RJ45 plug toolCT34CT28CT110CT36Krone punch down tool(made by Krone)Mini5 Krone compatible punchdown toolMini5 punch down tool for Mini5/6modules, Mini5 patch panels &Krone compatible products.Mini5 spring loaded impact toolfor Krone compatible products.CT05CT34CT28CT36Mini5 110 punch down tool CT110All the above tools terminate & cut wires."Hubbell" 1 punch tool for"Xcelerator" jacks2 - STRUCTURED CABLING SYSTEMS (TOOLING)Crimp tool & die set for Cat5e plugCT5-8Die set only for Cat5e plugCD5-8Wire Prep tool arranges conductorsin sequence providing easy way to cutconductors to length.WPT-8Crimp tool forCat6 plugMPT5-81 punch tool with head, blades &Snap-Ex termination aid.Additional Snap-Ex aid.TX4PHXTP‘Jack Knuckles’ termination aid. HXTAFor use only with Hubbell CAT5e & CAT6"Xcelerator" jacks. This tool punches down& cuts all 4 pairs simultaneously saving timeover traditional punch down tools thatrequire multiple cycles.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk33

CrimpTools & Punch Down Tools"Panduit" termination tool"Tempo" CableCaster wirepulling toolFibre toolsSTRUCTURED CABLING SYSTEMS (TOOLING) - 2For CJ5E series & cat 6 jacksCGJTFor CJ58 series jacksCJT-XProvides quick & easy termination ofPanduit CAT5e & CAT6 jacks. Eliminatesthe need for pliers & ensures conductorsare fully terminated."Nexans" comfort tool420.695For faster installation of Nexans CAT5eand CAT6 "Lanmark" jacks. Snaps rearcover into position.06186The CableCaster allows you to easily pull apulling string above false ceilings etc.After casting the string into place use thestring to pull in light weightcommunication cable. The CableCaster issupplied with 3 darts and can launch adart 15.25Mtrs or 50 feet.Coax crimp tool & stripperStripping tools, crimp tools & cutters.See pages 48-49.D type toolingCT08CAT5e/CAT6 Cable strippersCJSTCT33CT01ST01Ratchet Crimp tool for RG58/9907,RG59 & RG62Stripper for RG58/9907, RG59 &RG62 (3 blades)Fibre tool kitCT01ST01DCM10 91285-1Crimp tool for stamped &formed contactsCT08"Minilink" low cost D contactinsertion/extraction toolDCM10"AMP" D contact insertion/extraction toolwith replaceable tips 91285-1Panduit cable stripperCJSTMini5 cable stripperCT33Panduit cable stripper strips UTP and STPCAT5e/CAT6 cable. Insert cable and rotatethe tool twice then remove cable for aquick clean strip.Mini5 cable stripper strips UTP/STP CAT5eand CAT6 cable. Also strips two pair, fourpair, six pair & eight pair flat cable usedwith RJ plugs.V.35 toolingMT-0053Tools & consumables in a high qualitycase. Kit contains: No Nik stripper, Millerstripper, economy scribe, Jacket stripper,Buffer tube strippers, Pliers, Screwdriverset, matching gel, alcohol, foam swabs,kim wipes, utility blade, scissors, tweezers,black tape, storage box, tape measure,piano wire, ST continuity tester, cablemarkers, cable ties, red black & greenshrink tube, fusion splice sleeves & crimptool.Crimp tool for contactsContact extraction toolCTV35BV35EXT34Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk

Sharpmark Labelling SystemLabels for Mini5/6 PanelsAdhesive polyester for laser printersLabels for Hubbell PanelsAdhesive polyester for laser printersUniversal labelling software suitable formost leading brands of patch panels,dataports and patch cables.See www.sharpmark.co.ukSharpmark SoftwareSoftware diskSWAREThe software comes on a single CD and iscompatible with Windows 95,98,2000 orNT4.0. Easy to use, it is pre-loaded withall the Sharpmark label part numbers anda wizard which helps you set up yourlabel with the right part number andlayout. The Labelling software has beendesigned to work with all leading brandsof patch panels and dataports. It alsoallows cable labelling with the selflaminating wrap around style, in variouscolours.For Pt Numberlabels per packMP24S-C5EBK 520 PL2MT66-M24NCM 1040 PL9MT66-M48NCM 1040 PL9MT66-M241U 1040 PL9MT66-M482U 1040 PL9MP24A-K11-C5CBK 780 PL10MP48A-K11-C5CBK 780 PL10MP24T-KRO-CECBK 780 PL10MP48T-KRO-CECBK 780 PL10MP24-KRO-BLUE 780 PL10MP24-KRO-BLUE 780 PL10Labels for Mini5/6Faceplates/ModulesNon Adhesive perforated Card for allprintersFor Pt Numberlabels per packMT50-SAMK 280 PL15MT66-SAMK 280 PL15MT50-SAMS 280 PL15MT66-SAMS 280 PL15MT50-SADP 280 PL15MT50-DADP 280 PL15MT50-QADP 280 PL15MT66-SADP 280 PL15MT66-DADP 280 PL15MT66-QADP 280 PL15MT50-SAMK 280 PL15MT50-SSADP 280 PL15MT50-SDADP 280 PL15MT50-SLJKLP 4,320 CL15MT66-SSADP 280 PL15MT66-SDADP 280 PL15Adhesive polyester for laser printersMT66-SLJK 1260 CL12For Pt Number labels per packPSC5E24 520 PL2PSC5E48 520 PL2MCC24100BT19 520 PL2MCC48100BT19 520 PL2MCC2410BT19 520 PL2MCC4810BT19 520 PL2UDX series 1040 PL9Labels for HubbellModulesAdhesive polyester for laser printersEM1S 2070 CL2EM6S 2070 CL2Labels for Panduit PanelsAdhesive polyester for laser printersFor Pt Numberlabels per packCJ5E88T 2080 CL13CJ688T3 2080 CL13CP24BL 1040 PL9CPPL24WBL 1040 PL9CP24WSBL 1040 PL9CP48BL 1040 PL9CP72BL 320 PL23DP24588110B 1760 PL24DP48588110B 1760 PL24Labels for PanduitfaceplatesNon-Adhesive SolutionCFPUKS2SAW 1500 CL14CFPUKS2SAW-2G 1500 CL14Colour Options2 - STRUCTURED CABLING SYSTEMS (LABELLING)Cable LabelsSelf laminating wrap aroundadhesive polyester style for laserprinters.Max Cable Labels Size (mm)Dia Per Pack H x W*8mm 1050 38x12.7 SLL4L8mm 1029 38x25.4 SLL10L8mm 5145 38x25.4 SLL10L-512mm 1050 57x25.4 SLL12L35mm 420 140x25.4 SLL24L* For print area on labels see below:SLL4L: 12.7(h)x12.7(w)mmSLL10L: 12.7(h)x25.4(w)mmSLL12L: 19.0(h)x25.4(w)mmSLL24L: 30.0(h)x25.4(w)mmLabels for Nexans PanelsAdhesive polyester for laser printersSuitable forlabels per packEssential Panels 1760 PL24*LANmark Panels 360 PL19***PL24 is adhesive for laser printers.** PL19 is non adhesive for all printers.Labels for NexansfaceplatesPerforated Card for all PrintersSuitable forlabels per packModules 2070 CL2*Twin outlet dataports 2900 CL16***CL2 is adhesive for laser printers.** CL16 is non adhesive for all printers.All the labels shown on this page arewhite. Other available colours are: Red,Blue, Green, Yellow, Mauve, Grey andOrange. For colours other than white addthe requested colour to the end of thepart number. e.g. SLL4LRED.Labels for other cablingsystemsLabels for other systems are alsoavailable.Please contact our sales office for details.Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk35

Tempo DocIT Cable Management SoftwareSTRUCTURED CABLING SYSTEMS (SOFTWARE) - 2Untangle the web of cabling with DocIT.Knowing what`s out there, where is is and how it is connected is the key to network cable management.With automated documention and detailed reporting, DocIT speeds upmanagement tasks. Performs end to end cable tracking, asset management, userprofiles and more with simple point and click features.Throughout a single building or an entire campus DocIT can track it all. Its uniquedatabase navigator and Visio diagram interface makes DocITthe most userfriendly cable management system on the market.EasyCable Management doesn't have to be difficult. DocIT`s dynamic user interfacemakes it simple to document cabling, hardware, users, assets, telephony andlegacy connections with a click of your mouse.CompliantProviding network documentation is no longer an option, it is a requirement. And with the newly revisedANSI/TIA/EIA 606A standard how and what you need to document has changed. DocIT address these newrequirements as well as many more optional ones. From class 1 to class 4 DocIT can handle them all.Simple to useSimple data population structures allow you to set up an entire network in minutes.Using "smart" drawings and floor plans automatically linked to a connectivity database, you can simplify daily tasks.No complicated keystrokes to remember, just point and click to design an entire infrastructure from the campus tothe jack.Link a user, connect a device then import test results. Track all types of cables and utilisation end to end. Whetherit's category 2 - 6, fibre optics, coaxial cable or high pair count copper being user for workstation cabling orbackbone cabling, DocIT can document it all.This includes building-to-building runs and closet interconnects. DocIT can be used to track both industry standardscompliant cabling as well as legacy systems.Fully integratedIntegrated "work order" system eliminates the hard work. With DocIT you never have to leave your desk to gatherfacts about current and proposed configuration changes only to return and write up your findings manually.DocIT automatically collects the details for the devices and locations, then prints a work order with the instructionsfor the technician. If more information is needed floor plans and closet diagrams can be printed as well, depictingexact placement.When the work is done, hit the "complete" button for that order and DocIT automatically updates your databaseand drawings. No need for time-consuming data entry after the real work is done.FeaturesFull ANSI/TIA/EIA 606A complianceTermination hardwareHorizontal cablingBackbone cablingUser profiles including photographsData,Voice and workstation devicesWork order systemCircuit traceAsset TrackingReportsOutside PlantVisio Enterprise /200 interfaceCable tester downloadFire stoppingGrounding and bondingPlus many more features.DocIT Lite 1 user version max 500 outletsDocIT Single user 1 client version unlimited outletsDocIT 5 user client version unlimited outletsM0800/03AM0800/04AM0800/05A36Sales: 01279 757775 • Fax: 01279 653535 • E-mail: sales@minitran.co.uk • www.minitran.co.uk