MZEU-K Series Cam Clutch English - Tsubaki Europe
MZEU-K Series Cam Clutch English - Tsubaki Europe MZEU-K Series Cam Clutch English - Tsubaki Europe
- Cam Clutches series MZEU-K with E3 torque arm and E4 cover -61. Inner race2. Outer race3. Cam4. Spring5. Bearing6. Side plate7. E3 torque arm8. E4 cover9. Pin10. Set screw11. Hex socket cap bolt12. Set screwBasic type MZEU-K Cam Clutch provided with E3 torque arm and E4 cover. Summary of parts and dimensions(referring to table below).- dimensions and capacities -Model Torque Max. overrunning speed Drag Bore Keyway A A CB F L M 1Q R S T U Weightcapacity Inner race Outer race torque sizeN·m r/min r/min N·m H7 h7 kgMZEU12K E3+E4 60 2,000 1,000 0.20 12 4×1.8 42 53 62 20 0.8 13.5 44 59 10 10 6.0 1.0MZEU15K E3+E4 100 1,800 900 0.20 15 5×2.3 52 68 68 25 0.8 13.5 47 62 10 10 10.0 1.5MZEU20K E3+E4 245 1,600 700 0.29 20 6×2.8 57 73 75 30 0.8 15.0 54 72 12 11 10.0 2.0MZEU25K E3+E4 425 1,600 600 0.33 25 8×3.3 60 76 90 40 0.8 19.0 62 84 16 14 10.0 2.9MZEU30K E3+E4 735 1,500 500 0.39 30 8×3.3 68 84 100 45 1.0 19.0 68 92 16 14 10.0 4.3MZEU35K E3+E4 1,015 1,400 300 0.49 35 10×3.3 74 92 110 50 1.0 22.0 76 102 20 18 12.0 5.3MZEU40K E3+E4 1,350 1,400 300 0.59 40 12×3.3 86 105 125 55 1.3 22.0 85 112 20 18 12.0 7.8MZEU45K E3+E4 1,620 1,400 300 0.69 45 14×3.8 86 108 130 60 1.3 25.0 90 120 25 22 15.0 9.6MZEU50K E3+E4 2,070 1,300 250 0.79 50 14×3.8 94 113 150 70 1.3 25.0 102 135 25 22 12.0 12.1MZEU55K E3+E4 2,400 1,300 250 0.88 55 16×4.3 104 126 160 75 1.5 30.0 108 142 32 25 15.0 15.2MZEU60K E3+E4 2,950 1,200 250 0.98 60 18×4.4 114 137 170 80 1.5 30.0 112 145 32 25 15.0 17.7MZEU70K E3+E4 4,210 1,100 250 1.27 70 20×4.9 134 164.5 190 90 1.8 35.0 135 175 38 30 22.5 26.5MZEU80K E3+E4 5,170 800 200 1.38 80 22×5.4 144 168 210 105 1.8 35.0 145 185 38 30 16.0 33.6MZEU90 E3+E4 12,000 550 150 3.76 90 25×5.4 158 192 230 120 2.0 45.0 155 205 50 40 27.0 39.0MZEU100 E3+E4 17,600 500 130 4.31 100 28×6.4 182 217 270 140 2.0 45.0 180 230 50 40 28.0 67.4MZEU130 E3+E4 24,500 400 110 5.39 130 32×7.4 212 250 310 160 2.5 60.0 205 268 68 55 30.0 100.2MZEU150E3+E4 33,800 300 80 6.47 150 36×8.4 246 286 400 200 2.5 60.0 255 325 68 55 32.0 194.8Note: For the dimensions: bore size and B we recommend the tolerances H7 and h7 as stated in the table above.1. This version of the MZEU-K CamClutch comes as a combination ofa basic type clutch, an E3 torquearm and an E4 cover, each onepacked and supplied as an individualpart set.Each part set is delivered with aflange kit consisting of bolts,grease nipple, locker set screwand seal plug. The E3 kit comeswith a an extra pin and set screw.See drawing and table above no.9 & 10.2. Check the direction of rotationbefore assembling, then mountboth flanges making use of theflange kit.3. Before mounting the sizes MZEU90 - MZEU150apply the sealing adhesive, included with the partsets, between body (outer race surface) and the- installation and usage -Installation example 4.optional part, to prevent leakageof oil during operation.4. For the sizes MZEU12-K up toMZEU80-K assemble the shaftend plate onto the shaft beforeclosing with the E4 cover. Referto installation example 4.5. Before mounting the E4 cover onModel MZEU90 up to MZEU150,packing should be fitted betweenthe end surface of the innerrace and the surface of theend plate, using sealing, washerand bolt(s). Refer to installationexample 4.6. When installing the optional parts in the oppositeway the direction of the clutch’s rotation canbe changed.7. Refer to page 10 for other usage indicators andfurther advise.
- Cam Clutches series MZEU-K with E5 flanges on both sides -1. Inner race2. Outer race3. Cam4. Spring5. Bearing6. Side plate7. E5 flange8. Hex socket cap bolt9. Set screw7Basic type MZEU-K Cam Clutch provided with E5 flanges on both sides. Summary of parts and dimensions(referring to table below).- dimensions and capacities -Model Torque Max. overrunning speed Drag Bore Keyway A B B FC D F L M b t 1Weightcapacity Inner race Outer race torque sizeN·m r/min r/min N·m H7 h7 P10 kgMZEU12K E5+E5 60 2,000 1,000 0.20 12 4×1.8 42 62 70 20 51 20 0,8 10,0 4 2.5 0.5MZEU15K E5+E5 100 1,800 900 0.20 15 5×2.3 52 68 76 28 56 25 0,8 11,0 5 3.0 0.8MZEU20K E5+E5 245 1,600 700 0.29 20 6×2.8 57 75 84 34 64 30 0,8 10,5 6 3.5 1.2MZEU25K E5+E5 425 1,600 600 0.33 25 8×3.3 60 90 99 35 78 40 0,8 11,5 8 4.0 1.8MZEU30K E5+E5 735 1,500 500 0.39 30 8×3.3 68 100 109 43 87 45 1,0 11,5 8 4.0 2.6MZEU35K E5+E5 1,015 1,400 300 0.49 35 10×3.3 74 110 119 45 96 50 1,0 13,5 10 5.0 3.2MZEU40K E5+E5 1,350 1,400 300 0.59 40 12×3.3 86 125 135 53 108 55 1,3 15,5 12 5.0 4.8MZEU45K E5+E5 1,620 1,400 300 0.69 45 14×3.8 86 130 140 53 112 60 1,3 15,5 14 5.5 6.2MZEU50K E5+E5 2,070 1,300 250 0.79 50 14×3.8 94 150 160 64 132 70 1,3 14,0 14 5.5 8.2MZEU55K E5+E5 2,400 1,300 250 0.88 55 16×4.3 104 160 170 66 138 75 1,5 18,0 16 6.0 9.5MZEU60K E5+E5 2,950 1,200 250 0.98 60 18×4.4 114 170 182 78 150 80 1,5 17,0 18 7.0 12.3MZEU70K E5+E5 4,210 1,100 250 1.27 70 20×4.9 134 190 202 95 165 90 1,8 18,5 20 7.5 18.1MZEU80K E5+E5 5,170 800 200 1.38 80 22×5.4 144 210 222 100 185 105 1,8 21,0 22 9.0 23.1MZEU90K E5+E5 12,000 450 150 4.70 90 25×5.4 158 230 242 115 206 120 2,0 20,5 25 9.0 28.1MZEU100K E5+E5 17,600 400 130 5.39 100 28×6.4 182 270 282 120 240 140 2,0 30,0 28 10.0 46.3MZEU130K E5+E5 24,500 320 110 6.76 130 32×7.4 212 310 322 152 278 160 2,5 29,0 32 11.0 70.2MZEU150K E5+E5 33,800 240 80 8.13 150 36×8.4 246 400 412 180 360 200 2,5 32,0 36 12.0 146.3Note: For the dimensions: bore size, B and b we recommend the tolerances H7, h7 and P10 as stated in the table above.- installation and usage -1. This version of the MZEU-K CamClutch comes as a combination ofa basic type clutch, and two E5flanges, each one packed andsupplied as an individual part set.Each part set comes with a completeflange kit, containing anumber of bolts, a grease nipple,a locker set screw and a seal plug.2. Check the direction of rotationbefore assembling, then mountboth flanges making use of theflange kit.3. Before mounting the sizesMZEU90- MZEU150 apply thesealing adhesive, which comesalong with the part sets, betweenbody (outer race surface) and theInstallation example 5.optional part, to prevent leakageof oil during operation.4. Insert the Cam Clutch into the appropriateunit (gear, sprocket,pulley etc.). We recommend a toleranceof H7 for the bore size.Fix the key and close the unitwith the second E5 flange, makinguse of the flange kit.5. MZEU-K clutches with E5 and E5flanges can be used in both rotationdirections.6. For high speed indexing applications(over 50 c/min) strongsprings are recommended andcan be supplied accordingly.7. Refer to page 10 for other usageindicators and further advise.
- Page 1 and 2: CAM CLUTCHESMZEU-K SERIESTSUBAKI EM
- Page 4 and 5: - Cam Clutches series MZEU-K with E
- Page 8 and 9: - Cam Clutches series MZEU-K with E
- Page 10 and 11: - lubrication and maintenance -The
- Page 12: - more Cam Clutches from Tsubaki Em
- <strong>Cam</strong> <strong>Clutch</strong>es series <strong>MZEU</strong>-K with E3 torque arm and E4 cover -61. Inner race2. Outer race3. <strong>Cam</strong>4. Spring5. Bearing6. Side plate7. E3 torque arm8. E4 cover9. Pin10. Set screw11. Hex socket cap bolt12. Set screwBasic type <strong>MZEU</strong>-K <strong>Cam</strong> <strong>Clutch</strong> provided with E3 torque arm and E4 cover. Summary of parts and dimensions(referring to table below).- dimensions and capacities -Model Torque Max. overrunning speed Drag Bore Keyway A A CB F L M 1Q R S T U Weightcapacity Inner race Outer race torque sizeN·m r/min r/min N·m H7 h7 kg<strong>MZEU</strong>12K E3+E4 60 2,000 1,000 0.20 12 4×1.8 42 53 62 20 0.8 13.5 44 59 10 10 6.0 1.0<strong>MZEU</strong>15K E3+E4 100 1,800 900 0.20 15 5×2.3 52 68 68 25 0.8 13.5 47 62 10 10 10.0 1.5<strong>MZEU</strong>20K E3+E4 245 1,600 700 0.29 20 6×2.8 57 73 75 30 0.8 15.0 54 72 12 11 10.0 2.0<strong>MZEU</strong>25K E3+E4 425 1,600 600 0.33 25 8×3.3 60 76 90 40 0.8 19.0 62 84 16 14 10.0 2.9<strong>MZEU</strong>30K E3+E4 735 1,500 500 0.39 30 8×3.3 68 84 100 45 1.0 19.0 68 92 16 14 10.0 4.3<strong>MZEU</strong>35K E3+E4 1,015 1,400 300 0.49 35 10×3.3 74 92 110 50 1.0 22.0 76 102 20 18 12.0 5.3<strong>MZEU</strong>40K E3+E4 1,350 1,400 300 0.59 40 12×3.3 86 105 125 55 1.3 22.0 85 112 20 18 12.0 7.8<strong>MZEU</strong>45K E3+E4 1,620 1,400 300 0.69 45 14×3.8 86 108 130 60 1.3 25.0 90 120 25 22 15.0 9.6<strong>MZEU</strong>50K E3+E4 2,070 1,300 250 0.79 50 14×3.8 94 113 150 70 1.3 25.0 102 135 25 22 12.0 12.1<strong>MZEU</strong>55K E3+E4 2,400 1,300 250 0.88 55 16×4.3 104 126 160 75 1.5 30.0 108 142 32 25 15.0 15.2<strong>MZEU</strong>60K E3+E4 2,950 1,200 250 0.98 60 18×4.4 114 137 170 80 1.5 30.0 112 145 32 25 15.0 17.7<strong>MZEU</strong>70K E3+E4 4,210 1,100 250 1.27 70 20×4.9 134 164.5 190 90 1.8 35.0 135 175 38 30 22.5 26.5<strong>MZEU</strong>80K E3+E4 5,170 800 200 1.38 80 22×5.4 144 168 210 105 1.8 35.0 145 185 38 30 16.0 33.6<strong>MZEU</strong>90 E3+E4 12,000 550 150 3.76 90 25×5.4 158 192 230 120 2.0 45.0 155 205 50 40 27.0 39.0<strong>MZEU</strong>100 E3+E4 17,600 500 130 4.31 100 28×6.4 182 217 270 140 2.0 45.0 180 230 50 40 28.0 67.4<strong>MZEU</strong>130 E3+E4 24,500 400 110 5.39 130 32×7.4 212 250 310 160 2.5 60.0 205 268 68 55 30.0 100.2<strong>MZEU</strong>150E3+E4 33,800 300 80 6.47 150 36×8.4 246 286 400 200 2.5 60.0 255 325 68 55 32.0 194.8Note: For the dimensions: bore size and B we recommend the tolerances H7 and h7 as stated in the table above.1. This version of the <strong>MZEU</strong>-K <strong>Cam</strong><strong>Clutch</strong> comes as a combination ofa basic type clutch, an E3 torquearm and an E4 cover, each onepacked and supplied as an individualpart set.Each part set is delivered with aflange kit consisting of bolts,grease nipple, locker set screwand seal plug. The E3 kit comeswith a an extra pin and set screw.See drawing and table above no.9 & 10.2. Check the direction of rotationbefore assembling, then mountboth flanges making use of theflange kit.3. Before mounting the sizes <strong>MZEU</strong>90 - <strong>MZEU</strong>150apply the sealing adhesive, included with the partsets, between body (outer race surface) and the- installation and usage -Installation example 4.optional part, to prevent leakageof oil during operation.4. For the sizes <strong>MZEU</strong>12-K up to<strong>MZEU</strong>80-K assemble the shaftend plate onto the shaft beforeclosing with the E4 cover. Referto installation example 4.5. Before mounting the E4 cover onModel <strong>MZEU</strong>90 up to <strong>MZEU</strong>150,packing should be fitted betweenthe end surface of the innerrace and the surface of theend plate, using sealing, washerand bolt(s). Refer to installationexample 4.6. When installing the optional parts in the oppositeway the direction of the clutch’s rotation canbe changed.7. Refer to page 10 for other usage indicators andfurther advise.
Change language