Installation Instructions - Freelance 1700mm Shower Over ... - Kohler

FREELANCEINSTALLATION INSTRUCTIONSACRYLIC BATH6078A-0 LH / 6079A-0 RH (no upstand)6090A-0 LH / 6092A-0 RH (25mm upstand)BEFORE YOU BEGINPlease read these instructions carefully to familiarize yourself with the required tools, materials, and installationsequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes.In addtion to proper installation, read all operating and safety instructions.All information is based on the latest product information available at the time of publication. Kohler reservesthe right to make changes in product characteristics, packaging, or availability at any time without notice.These instructions contain important care, cleaning, and warranty information.PLEASE LEAVE THESE INSTRUCTIONS FOR THE CONSUMERPlease provide adequate available space for the bath unit in accordance with rough in guide. Arrange the locationof drain in advance.All installations must comply with council and local authority by laws. It is the responsibility of the installer to ensurethat the waste is made watertight by means of silicone sealant or caulking compound.PRODUCT REQUIREMENTS Observe all local plumbing codes.Install the unit to a level subfloor.Provide properly-dimensioned framing.Baths are designed for a variety of installations, depending upon the model chosen. Uncrate and inspect bath for damage. Leave all materials in the crate during construction to prevent damage. FixtureBathing wellBasin area1408x710mmTop area1596x781mmWeight42kgWater depth445mmCapacity to overflow264L Accessories/HardwareDrain T151010 Approximate measurements for comparison only.1131904-A01-B1Copyright Kohler NZ Ltd., 2009

ROUGHING-INLeft hand shower end ( 6078A-0 , 6090A-0 )UNIT: mm45777683O 522578717001596421886 781 710O 50513 667 7321408Right hand shower end ( 6079A-0, 6092A-0 )UNIT: mm45725O 521700159668378777421732 667 513O50710 781 88614081131904-A01-B2

INSTALL THE BATH Adjust the feet under the bath to make it level. Tightenthe nut to fix the height of the bath.The bath must be installed level on all top edges.The rim and the base of the bath must be fullysupported. Floor should be flat, level and free of anybumps or protrusions.Remove protective film around the waste and alongthe tiling bead prior to installation in order to make awatertight seal at these points possible.Keep the clearance of a finger from floor to theapron for removing the apron.Adjustable FeetNutHeight of a Finger Ensure a watertight seal on the bath drainconnections.1 ). When the bath is securely positioned, connect thedrain to the trap.2 ). Install the tapware valving and spout tee. Open thehot and cold water valves, and check the supplyconnections for leaks.3).Run water into the bath, and check the drainconnections for leaks.4). Fill the bath up to the overflow level and checkoverflow for any leaks.1131904-A01-B4

If the apron needs removing, please follow the stepsbelow:1). Extend your finger into clearance between floor andbath, pull the apron forth to release the clip from thefixing base.2). Pull the apron downwards to release it from the bath.Please follow the steps below to install apron:1). Install the smaller apron first. Once secured install theremaining apron.2). Insert the top of the apron into the clearance betweenspring and bath to fix the apron.3). Push the apron to clip it into the fixing base.The apron is now fixed on the bath.Without BathApronFixing BaseClipApronSpringBath BracketThe Apron is installedThe Apron is Separated 1). The back corner edges of the bath should be supported with a timber batton as shown on the following page.2). Ensure that a suitable water proofing membrane is used to seal the ustand to wall joint before tiling.Support this edge with timber battenSupport this edge with timber batten1131904-A01-B5

BRICK CONSTRUCTIONBRICK CRADLE HOB MOUNT FLUSH FRONTNG SILICONESEALANTTILEBRICKAPPROVEDTILEBACKINGTILEAPPROVEDTILEBACKINGBRICKBRICKTILEAPPROVEDTILEBACKINGTIMBER CONSTRUCTIONWOODEN CRADLE HOB MOUNT FLUSH FRONTNG SILICONESEALANTGIBBOARDACRILYCWALL LININGTIMBERSUPORTTILESAPPROVEDTILEBACKINGTIMBERSUPORTGIBBOARDAPPROVEDTILEBACKINGTILES 1). After the bath is installed ensure that the markededges are well sealed.SealantSealantSealantSealant1131904-A01-B7

DIRLLING AND CUTTING ACRYLICSmall holes can be drilled with a twist drill, but the cutting edge MUST be backed off with an oilstone (the sharp edge dulled). Large holes must be drilled with a hole saw. Maximum drill size-12mm. Drillspeeds-6mm x 1800 RPM-12 mm x 900 RPM. Always drill from acrylic surface.If for any reason the acrylic requires cutting, use a fine tooth hacksaw and proceed with caution.Edges can be smoothed with a second-cut file and medium-fine sandpaper. If the surface of the acrylicshould happen to be damaged, it can be restored by polishing with appropriate materials. Deep scratchescan be removed by rubbing with 600 grade wet & dry sandpaper then polishing.CLEAN-UP AFTER INSTALLATIONWhen cleaning up after installation, do not use abrasive cleansers as they may scratch and dull the surface.Use warm water and liquid or a non-abrasive detergent to clean the surface.Stubborn stains, paint, or tar can be removed with mineral spirits. Do not use cleaners containing solvent.Plaster can be removed by scraping with wood edge. Do not use metal scrapers, wire brushes, or other metaltools.IMPORTANT CONSUMER INFORMATION When selecting cleaning products please check the manufacturers instructions to ensure their suitability for useon acrylic products. Use of un-suitable cleaning products may cause damage to the acrylic surface.1131904-A01-B8

FREELANCESERVICE PARTS PAGEACRYLIC BATH6078A-0 / 6079A-01064204Corner Support1065601GB/T 5781 M10 40Zinc Plating1065603Nut GB/T 41 M101065602Spring Space GB/T93 10 Zinc Plating1064203Clip Holder1065603Nut GB/T 41 M101022879Levelling Glide Kit1065595Side Apron Assy. Freelance LH1066271Side Apron Assy. Freelance RH (Mirrored)1065593Apron Assy LH, Freelance1065594Apron Assy RH Freelance (Mirrored)1065600 Nut GB/T 41 M5Zinc Plating1065598 SpringSpace GB/T 93 5106446890 Deqree Slice1064202Apron Clip Assy1064198Apron Clip1064199Clip Base1065599 GB/T 5781M5 10 Zinc Plating1064205Flex Slice Base1047907Spring Clip** Color code must be specified when ordering.1131904-A01-B9

CONTACT AND WARRANTY INFORMATIONFor warranty information, please visit our websiteAustraliawww.au.kohler.comNew Zealandwww.kohler.co.nzCALL US FOR HELP1131904-A01-B