MCS-605-1 Pivot Point Tension Sensor for Warner Electric Tension ...

DIST. AUTORIZADO®MEX (55) 53 63 23 31QRO (442) 1 95 72 60MTY (81) 83 54 10 18ventas@industrialmagza.comP-362MCS-605-1 Pivot Point Tension Sensor forWarner Electric Tension Control SystemInstallation InstructionsThe MCS-605-1 Tension Sensor is used with theWarner Tension Control System to providesmooth control of unwind stands operating atany speed. The sensor is especially convenientin applications having small dancer arms and iscomplete with versatile mounting brackets. Thepivot point sensor does not add additionalweight to the dancer arm.MCS-605 Pivot Point SensorA Complete Dancer System• For Unwind Stands• Dancer Roll System• Stable• Electromagnetic Brakes• Quiet• Closed Loop ControlMCS-605 Pivot Point Sensor• Off-the-shelf Availability fromyour local Warner DistributorAn Altra Industrial Motion Company

Dimensions/InstallationDIST. AUTORIZADO®MEX (55) 53 63 23 31QRO (442) 1 95 72 60MTY (81) 83 54 10 18ventas@industrialmagza.com4-3/81-11/16 Nom.Bracket (see note 1)2 Dia.CouplingSupplied.250/.253 Dia.1/2 Deep1-1/4Pin SuppliedDancerPivotShaft5/1615' JacketNOTES:1. TWO BRACKETS ARE SUPPLIEDWITH EACH UNIT SO THAT THECUSTOMER CAN MOUNT THEMCS-605-1 ACCORDINGLY.2. BRACKETS ARE MADE FROM14 GAUGE (.0747) STEEL.8-32 Screws(3 supplied)10-32 ScrewsWashers & Nuts(2 supplied)3 Holes 3/16 Dia. on1.50 B.C. EquallySpaced1. Using a 1/4" drill, drill a hole in the center ofthe dancer pivot shaft 1/2" deep.2. Drive the supplied pin into the hole in theshaft until half its length remains exposed.3. Assemble the brackets and mount thesensor on the bracket.4. Position the sensor and bracket on themachine so the sensor shaft and the pin arealigned and separated by 1/8 to 1/4 inch.While holding the sensor and bracket in theabove position, mark the centers of thebracket holes on the machine. Drill and tapholes in the machine for 8-32 screws.5. Connect the sensor shaft to the pin with theflexible coupling provided. The index mark onthe sensor shaft must be aligned with theindex mark on the sensor face when thedancer arm is near the midtravel position.6. Mount the sensor and bracket to themachine. Connect the sensor to the tensioncontrol unit with the cable assembly inaccordance with the instructions suppliedwith the control unit.WarrantyWarner Electric LLC warrants that it will repair or replace (whichever it deemsadvisable) any product manufactured and sold by it which proves to be defectivein material or workmanship within a period of one (1) year from the date oforiginal purchase for consumer, commercial or industrial use.This warranty extends only to the original purchaser and is not transferable orassignable without Warner Electric LLC’s prior consent.Warranty service can be obtained in the U.S.A. by returning any defectiveproduct, transportation charges prepaid, to the appropriate Warner Electric LLCfactory. Additional warranty information may be obtained by writing theCustomer Satisfaction Department, Warner Electric LLC, 449 Gardner Street,South Beloit, Illinois 61080, or by calling 815-389-3771.A purchase receipt or other proof of original purchase will be required beforewarranty service is rendered. If found defective under the terms of this warranty,repair or replacement will be made, without charge, together with a refund fortransportation costs. If found not to be defective, you will be notified and, withyour consent, the item will be repaired or replaced and returned to you at yourexpense.This warranty covers normal use and does not cover damage or defect whichresults from alteration, accident, neglect, or improper installation, operation, ormaintenance.Some states do not allow limitation on how long an implied warranty lasts, sothe above limitation may not apply to you.Warner Electric LLC’s obligation under this warranty is limited to the repair orreplacement of the defective product and in no event shall Warner Electric LLCbe liable for consequential, indirect, or incidental damages of any kind incurredby reason of the manufacture, sale or use of any defective product. WarnerElectric LLC neither assumes nor authorizes any other person to give any otherwarranty or to assume any other obligation or liability on its behalf.WITH RESPECT TO CONSUMER USE OF THE PRODUCT, ANY IMPLIEDWARRANTIES WHICH THE CONSUMER MAY HAVE ARE LIMITED INDURATION TO ONE YEAR FROM THE DATE OF ORIGINAL CONSUMERPURCHASE. WITH RESPECT TO COMMERCIAL AND INDUSTRIALUSES OF THE PRODUCT, THE FOREGOING WARRANTY IS IN LIEU OF ANDEXCLUDES ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIEDBY OPERATION OF LAW OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS.Some states do not allow the exclusion or limitation of incidental orconsequential damages, so the above limitation or exclusion may not apply toyou. This warranty gives you specific legal rights and you may also have otherrights which vary from state to state.Changes in Dimensions and SpecificationsAll dimensions and specifications shown in Warner Electric catalogs are subjectto change without notice. Weights do not include weight of boxing for shipment.Certified prints will be furnished without charge on request to Warner Electric.Warner Electric LLC449 Gardner Street • South Beloit, IL 61080815-389-3771 • Fax: 815-389-2582www.warnerelectric.comAn Altra Industrial Motion CompanyP-362 11/07 Printed in USA