DOOR CONTROL COLLECTION 2013 - Architectural Hardware Direct

More documents

Recommendations

Info

Troubleshooting and MaintenanceFitting Applications1. Check that all instructions provided by the manufacturer are adhered to and that the door closer closes the door correctly.2. Ensure that all fixing screws, including the connection of arm to body are tight.3. Check the spring strength is set correctly and adjust if necessary.Our comprehensive range of Enduro and Enduromax door closers all come with detailed fitting instructions and technical information.The three common ways to fit surface mounted overhead closers are as follows. The full range of fitting instructions in PDF format can be obtained fromwww.carlislebrass.com4. Perform checks on any controls relating to delay, closing speed, latching action and back check, and adjust as required.5. Lightly lubricate arm joints and rollers with light oil or grease.6. Ensure that at all times, care and maintenance are carried out by competent personnel and that records are kept.7. Use chart below as a guide to checking your doorset.Figure 1 (Fig 1) Straight Arm ; Standard ApplicationThe closer is mounted on the pull side of the door with the arm fixed tothe frame on the hinge knuckle side of the door.Door closer cannotclose easilyDoor Application: Offices, stores, toilets etc, where doors open into areaswhich are usually small.For o/hd closersdisconnect armsDoes closer mechanismoperate freely?NOAdjust or replace doorcloserYESDoes the door movefreely?YESNOAre the hinges plumb?YESAre the hinges stiff?NOYESAdjust or ease hingesLubricate hingesFigure 66 (Fig 66) (Fig 6) Parallel Arm ApplicationThe closer is mounted on the push side of the door and the arm is fixedto the Figure 66 bracket, parallel to the door on the opposite side of thedoor to the hinge knuckle.Door Applications: Doors opening outwards to exterior, where aestheticsor space mean Figure 1 cannot be used.Re-connect closer armsNOIs the door scraping thefloor?YESRe-hand door or planebottom railNOIs latch resistance toostrong?YESAdjust strike plate andlubricate latchNOIs the door catching theframe?YESEase door and/or frameFigure 61 (Fig 61) Transom Mounted ApplicationIs the closer correctlyinstalled?Is the closer the right sizefor the door?NONORe-position closer accordingto template/instructionsReplace closer or adjustspring strength wherepossibleThe closer is mounted on the push side of the frame over the door andthe arm is fixed to the door on the opposite side to the hinge knuckle.Door Applications: Doors where there is insufficient material in the toprail to allow the closer to be fitted on glazed doors with unsufficient fixingfor closer body.Door closer closes thedoor easily30 31
32IndexAA45 29292914,1713,15,16,182425266202089107212119191111111119202020212727222227CDC85SC/RCDG003DCC2003DCC2024DCCEM3024DCEM2003DCEM2004DCF2003DCFS150DCFS250DCS2024DCS2025DCS2026DCT2024DCTS100DCTS150DCX2002DCX2003DCX2107DCX2201DCX2202DCX2203DCX3202DCXF105DCXF107DCXF108DCXT100DEFB100DEM100H2N1900H2N1950PSUA8
Page 3 and 4: ContentsDCF20036DCC2003CF17DCT20247
Page 5 and 6: Select the Correct Door Closer For
Page 7 and 8: MECHANICALMECHANICALDCS2024BCOverhe
Page 9 and 10: MECHANICALDCC2024SMSurface Mounted
Page 11 and 12: MECHANICALMECHANICALDCC2024CFConcea
Page 13 and 14: MECHANICALMECHANICALMECHANICALMECHA
Page 15 and 16: MECHANICALMECHANICALDCCEM3024Electr
Page 17: MECHANICALMECHANICALMECHANICALTrans
Page 21: Carlisle BrassParkhouse RoadCarlisl

DOOR CONTROL COLLECTION 2013 - Architectural Hardware Direct

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?