English manual - PHALLOSAN® forte penis enlargement

DEGebrauchsanweisungESInstruciones de usoGB/USInstructions for useITIstruzioni per l´usoFRMode d’emploiPT/BRManual de instruções

Dear Customer,Congratulations on purchasing PHALLOSAN®! This product has already been successfullyemployed for a wide range of indications such as penis enlargement, peniscurvature, erectile dysfunction, prostate follow-up treatment and/or induratio penisplastica (IPP).Preparation:Lay out the components of the orthopaedicPHALLOSAN® belt in front of you; use thebuckle (2) to adjust the belt to its greatest lengthand open the metal clip.109Please follow these instructions carefully!57823Package contents:1461. First of all determine the correct condom sizeusing the enclosed template. Measure thepenis shaft and the glans of the flaccid penis.1. Foam-rubber covered silicone ring, to be pulled over the penis2. Buckle for individual adjustment of the belt (3)3. Elastic belt, to be strapped around the body4. Nickel-free clip for securing the suction bell5. Suction bells in three sizes with sleeve condoms (S, M, L)6. Protector cap, to protect the glans against strong tension settings7. Pump ball for creating a micro-vacuum8. Measuring template9. DVD with product description10. Instructions for use2. Insert the protector cap over the penis asshown in the pictures. It is a matter of personalcomfort whether you leave the foreskinover the glans or draw it back. It is importantthat after fitting the cap as little air as possibleremains at the tip of the glans. It is advantageousto slip the protector cap over thepenis when the latter is in a slightly erectstate. The protector cap should protect yourpenis from the effects of possible excess tension.

After the protector cap has been fitted overthe glans, select the bell condom that is theoptimum size for you and remove it from itssealed package.Top: Wrong, pulled too far over the bell andnot powderedâThe glans must now be inserted into the centreof the bell. It may help to moisten the protectorcap with saliva to enable it to slip more easilyinto the suction bell.First of all we would like to draw your attentionto the new condom. The third generation ofsleeve condoms consists of medical silicone,thus ruling out the risk of irritation or allergicreactions. This innovation not only offers youimproved comfort – it provides a snug fitaround the penis.You can now adjust it to your individual sizefor optimized efficiency. For example, if youfeel that the M bell is the right size, but thecondom is too large for the penis shaft, youcan remove the S sleeve condom of the S belland place it on the M bell.âBottom: Right, and powdered.Please note that the condoms lose theircoating after a few days. We recommendpurchasing baby powder at a pharmacy ordrugstore and applying it to the outer surfaceof the condom. This coating will protect thecondom from friction and adhesion.1. The sleeve condom can now be rolled overthe entire penis shaft.3. Take up the belt previously laid out beforeyou and pull the foam rubber ring over thesuction ball and suction bell condom until itsits against the root of the penis. Now pull theend of the belt with the clip around your waistto the back until the clip is again pointingtowards the penis.The same can be done with the L bell and Msleeve condom. Please do not throw away asleeve condom that is too large, as you willneed it again in a few weeks!Never pull the S sleeve condom over the Lbell. This may cause the material to rupture.Please understand that suction bell condomsthat are too small or too large cannot beexchanged or refunded.Roll the sleeve condom to the edge of thebell and pull it behind the bead of the suctionbell. The opening of the suction bell is nowfree. Connect the suction ball to the suctionbell and insert it slightly into the tube end ofthe suction bell.2. Now press the suction ball. You will noticethat it only needs to be pressed a few timesand will remain dented. Having created thedesired micro-vacuum, the glans will bedrawn further into the bell.4. Firmly press the tube end between the suctionbell and the suction ball with the thumband index finger to prevent air from entering.Remove the suction ball and connect thesuction bell to the clip of the belt. Ensure thatthe tube end of the suction bell is secured inthe middle of the clip.

5. Shorten the stretch belt, making sure that thebelt slants upwards in the groin area. To dothis, pull the belt upwards around the buttockstowards the waist. If it slips into the foldof the buttocks, i.e. parallel to the penis, thetension will be further increased when sitting,which may be unpleasant.We would like to point out a special technicalfeature in the application of the suction bell. Putsimply, it is a suction bell with a seal. It is thereforenot important how far the sleeve condomreaches over the penis shaft. The sleeve condomis not designed to transfer the force to thepenis. It is transferred only by the mini-vacuumformed in the bell. The sealing condom is merelya seal between suction bell and penis shaft.Its purpose is not to absorb the force aroundthe penis.Care of the suction bell condomThe sleeve condom can and should bedetached from the bell. For hygienic reasons itshould be washed every day in lukewarmsoapy water. Remove the green sponge andwash this separately. Keep the sealing condomrolled up until you need it again.When it is attached to the bell, pay carefulattention that the bead of the bell sits in thegroove of the sealing condom at the thick endof the sealing condom. It is 0.0118 inches thickat this point. Insert your index finger to feel thethick part of the sealing condom and thegroove. Never pull the sealing condom too farover the bead of the bell, as the 0.3 mm thinsealing condom otherwise lies against the beadand may tear.âSleeve condom Notch suction bellNever forget to apply powder to the outside ofthe dry sleeve condom when rolled out afterwashing. Use baby powder from your drugstore,as it contains fatty aniline.Roll the sleeve condom back behind thebead on the bell as shown here:Apply baby powder to the outside of the rolledout sleeve condom and grip the tube-like endbetween your knees. You now have both handsfree.Roll it carefully behind the bead of the suctionbell. Take care not to damage the sleeve condomwith sharp finger nails or similar.Step-by-step plan for precise adjustment ofthe tension of the belt to the connective tissueof the penis.Preamble: The body’s connective tissuedepends on hereditary disposition and thusvaries widely. Recommending a uniform tensionsetting in terms of grams/kilograms wouldbe irresponsible from a medical point of view.We have therefore developed a step-by-stepplan to enable you to adjust the belt tensionprecisely to your type of connective tissue. Youwill achieve optimum results for penis enlargementin length and width without any negativeside-effects.1st day: Do not set the belt too tight (rely onyour subjective perception) and wear it for nomore than one hour before opening it anddetaching the sleeve condom. Examine thepoint on the penis between the opening of theurethra and the frenulum on the underside ofthe glans. This is the most sensitive tissue onthe penis! If it is reddened or swollen, the belttension was too tight. Suspend the applicationfor today. If there is no discolouring, mark thebelt on the sliding buckle. That completes theapplication for today.2nd day: Patients who suffered reddening theprevious day: If the point in question was reddenedor swollen, wear the belt for an hour withreduced tension. Then examine the point onthe penis between the opening of the urethraand the frenulum on the underside of the glans.If reddening or swelling can be seen at this

point, the tension of the belt was again too tight.Suspend the application for today. Patientswithout reddening or swelling from the previousday: extend the period of wear to two hours andthen examine the described point once again.Provided there is still no reddening or swelling,the application can be extended the next day bya further hour.3rd day and following days up to the 8thday:Patients whose penis exhibited reddening orswelling from the first day: If you were able towear the belt on the second day without furtherreddening or swelling at the described point,wear the belt for three hours on the third day.Should reddening or swelling occur after3 hours, reduce the tension and repeat thewearing time next day. If you observed no reddeningor swelling, extend the wearing time byone hour each day. In the event of reddening orswelling between urethra and the frenulum onthe underside of the glans in the next few daysreduce the tension of the belt, mark this pointon the belt with a pen and wear it the next daywith reduced tension the belt. Please ensurethat the green foam rubber disc pressesagainst the glans. Observe this step-by-stepplan and you will wear PHALLOSAN® withenthusiasm. Your penis will become measurablylonger and thicker in only a few months.You will experience only positive side-effectssuch as a stronger sex drive and pleasure, butwithout premature ejaculation. Reason: theblood circulation in the penis is greatlyenhanced during the application with PHAL-LOSAN®. This has a positive effect on theentire tissue and the nerve ends.The entire PHALLOSAN® team wishes you thebest of success!Length of application: PHALLOSAN® shouldbe worn 8–10 hours per day, even longer if possible!Please do not forget to take a break ofapprox. 5 minutes every 3 to 4 hours. Detachthe suction bell and massage the penis forapprox. 1 minute. After about 8 days this is nolonger necessary. The longer the daily use, thefaster the success! Many users wear PHAL-LOSAN® up to 12 hours per day and experiencethe corresponding success.After the 8-day adjustment phase PHAL-LOSAN® can also be worn at night. By thistime you will have calibrated the belt accordingly.The sleeve condom will stretch to accommodatea night-time erection and blood circulationwill not be impeded.Side-effects, precautionsPHALLOSAN® is used at your own risk, butdoes not incur any form of risk provided it isused according to the instructions. Particularlyin the first weeks of application, excess tensionon the penis should be avoided. Allow the bodytissue to become accustomed to PHAL-LOSAN® and set the belt (3) at first to only aslight tension. Every hour or so, check yourpenis for reddening (a sign of circulatory disturbance)and swelling.Should discolouration, pain or swelling neverthelessoccur, particularly in the region of theurethra, open the belt (3) immediately andexamine the penis for circulatory disturbanceand swelling.If swelling and/or blisters occur on the foreskinor glans, the belt (3) is set too tight. Take abreak until the swelling or blisters have disappeared.Then set the tension somewhat slacker.Please be patient, the success of the penisenlargement process is comparable to that of ajaw alignment. The continuity of elongation, notalone the amount of tension, is a guarantee ofsuccess!Do not wear PHALLOSAN® in the followingcircumstances:After alcohol consumption, taking drugs orpainkilling medication, sleeping pills and tranquillizers,because your natural perception ofpain may be compromised. Avoid using PHAL-LOSAN® in the event of infections or openwounds on the penis.How do I measure the exact increase in thelength of my penis?Please use a foot rule. Hold the penis in a flaccidstate away from the body (90 degrees) andalign the rule with the penis. Press the end ofthe rule against the pubic bone to measure thefull length of the penis.Follow the same procedure if you wish tomeasure your penis in an erect state.Important: At the start of the application youshould measure your exact body weight withoutclothing. When a person gains weight, a layerof fat forms – in particular – around the pubicarea. This layer of fat reduces the distancebetween the penis tip and the pubic bone, thusfalsifying (shortening) the result. Physicians callthis an abdominal apron.Re-ordering: All parts of PHALLOSAN® canbe re-ordered individually. If you have any furtherquestions or suggestions, feel free to contactour experts at any time free of charge.Calls incur only the normal phone charges.We reserve the right to make technical modifications,which will also be announced in theInternet at www.phallosan.at, www.phallosan.deand www.phallosan-info.ch.Manufacturer:Orbisan Ltd.UB3A Industrial EstateSAN Gwann, SGN 3000MaltaVAT ID. MT 20540812Company REG. C 53679Tel.: +356 21 47 02 76Fax: +356 21 47 02 77Email: service@phallosan.comMalta, 03.2012