GSM 11.11 version 6.2.0 - TTFN Smart card pages

More documents

Recommendations

Info

(GSM 11.11 version 6.2.0 Release 1997)30TS 100 977 V6.2.0 (1999-05)PREVIOUS: For a linear fixed EF the record pointer is decremented before the UPDATE RECORD function isperformed and the pointed record is updated. If the record pointer has not been previously set within the selectedEF, then UPDATE RECORD (previous) shall set the record pointer to the last record in this EF and this recordshall be updated. If the record pointer addresses the first record in a linear fixed EF, UPDATE RECORD(previous) shall not cause the record pointer to be changed, and no record shall be updated.For a cyclic EF the record containing the oldest data is updated, the record pointer is set to this record and thisrecord becomes record number 1.Input:- mode, record number (absolute mode only) and the length of the record;- the data used for updating the record.Output:- none.8.7 SEEKThis function searches through the current linear fixed EF to find a record starting with the given pattern. This functionshall only be performed if the READ access condition for this EF is satisfied. Two types of SEEK are defined:Type 1Type 2NOTE:The record pointer is set to the record containing the pattern, no output is available.The record pointer is set to the record containing the pattern, the output is the record number.A Phase 1 SIM only executes type 1 of the SEEK function.The SIM shall be able to accept any pattern length from 1 to 16 bytes inclusive. The length of the pattern shall notexceed the record length.Four modes are defined:- from the beginning forwards;- from the end backwards;- from the next location forwards;- from the previous location backwards.If the record pointer has not been previously set (its status is undefined) within the selected linear fixed EF, then thesearch begins:- with the first record in the case of SEEK from the next location forwards; or- with the last record in the case of SEEK from the previous location backwards.After a successful SEEK, the record pointer is set to the record in which the pattern was found. The record pointer shallnot be changed by an unsuccessful SEEK function.Input:- type and mode;- pattern;- length of the pattern.Output:- type 1: none;- type 2: status/record number8.8 INCREASEThis function adds the value given by the ME to the value of the last increased/updated record of the current cyclic EF,and stores the result into the oldest record. The record pointer is set to this record and this record becomes recordnumber 1. This function shall be used only if this EF has an INCREASE access condition assigned and this condition isfulfilled (see bytes 8 and 10 in the response parameters/data of the current EF, clause 9). The SIM shall not perform theincrease if the result would exceed the maximum value of the record (represented by all bytes set to 'FF').Input:ETSI
(GSM 11.11 version 6.2.0 Release 1997)31TS 100 977 V6.2.0 (1999-05)- the value to be added.Output:- value of the increased record;- value which has been added.8.9 VERIFY CHVThis function verifies the CHV presented by the ME by comparing it with the relevant one stored in the SIM. Theverification process is subject to the following conditions being fulfilled:- CHV is not disabled;- CHV is not blocked.If the access condition for a function to be performed on the last selected file is CHV1 or CHV2, then a successfulverification of the relevant CHV is required prior to the use of the function on this file unless the CHV is disabled.If the CHV presented is correct, the number of remaining CHV attempts for that CHV shall be reset to its initial value 3.If the CHV presented is false, the number of remaining CHV attempts for that CHV shall be decremented. After 3consecutive false CHV presentations, not necessarily in the same card session, the respective CHV shall be blocked andthe access condition can never be fulfilled until the UNBLOCK CHV function has been successfully performed on therespective CHV.Input:- indication CHV1/CHV2, CHV.Output:- none.8.10 CHANGE CHVThis function assigns a new value to the relevant CHV subject to the following conditions being fulfilled:- CHV is not disabled;- CHV is not blocked.The old and new CHV shall be presented.If the old CHV presented is correct, the number of remaining CHV attempts for that CHV shall be reset to its initialvalue 3 and the new value for the CHV becomes valid.If the old CHV presented is false, the number of remaining CHV attempts for that CHV shall be decremented and thevalue of the CHV is unchanged. After 3 consecutive false CHV presentations, not necessarily in the same card session,the respective CHV shall be blocked and the access condition can never be fulfilled until the UNBLOCK CHV functionhas been performed successfully on the respective CHV.Input:- indication CHV1/CHV2, old CHV, new CHV.Output:- none.8.11 DISABLE CHVThis function may only be applied to CHV1. The successful execution of this function has the effect that files protectedby CHV1 are now accessible as if they were marked "ALWAYS". The function DISABLE CHV shall not be executedby the SIM when CHV1 is already disabled or blocked.If the CHV1 presented is correct, the number of remaining CHV1 attempts shall be reset to its initial value 3 and CHV1shall be disabled.ETSI
Page 1: TS 100 977 V6.2.0 (1999-05)Technica
Page 4 and 5: (GSM 11.11 version 6.2.0 Release 19
Page 12 and 13: CIVILZSÁMBÉKI POLGÁR„ A kis J
Page 54: (GSM 11.11 version 6.2.0 Release 19
Page 81 and 82:
(GSM 11.11 version 6.2.0 Release 19
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
show all

GSM 11.11 version 6.2.0 - TTFN Smart card pages

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?