GSM 11.11 version 6.2.0 - TTFN Smart card pages

More documents

Recommendations

Info

(GSM 11.11 version 6.2.0 Release 1997)18TS 100 977 V6.2.0 (1999-05)A Phase 1 ME shall wait at least 744 clock cycles after having received the compulsory acknowledgement SW1 SW2 ofthe SLEEP command before it switches off the clock (if it is allowed to do so). It shall wait at least 744 clock cyclesbefore it sends the first command after having started the clock.5.7 BaudrateThe initial baudrate (during ATR) shall be: (clock frequency)/372. Subsequent baudrate shall be: (clock frequency)/372unless the PTS procedure has been successfully performed. In that case the negotiated baudrate shall be appliedaccording to subclause 5.8.2.5.8 Answer To Reset (ATR)The ATR is information presented by the SIM to the ME at the beginning of the card session and gives operationalrequirements.5.8.1 Structure and contentsThe following table gives an explanation of the characters specified in ISO/IEC 7816-3 [26] and the requirements fortheir use in GSM. The answer to reset consists of at most 33 characters. The ME shall be able to receive interfacecharacters for transmission protocols other than T=0, historical characters and a check byte, even if only T=0 is used bythe ME.ETSI
(GSM 11.11 version 6.2.0 Release 1997)19TS 100 977 V6.2.0 (1999-05)Table 5: ATRCharacter Contents sent bythe card1. Initial character coding convention for all alwayssubsequent charactersTS(direct or inverseconvention)2. Formatsubsequent interface alwayscharacter characters, number ofhistorical charactersT03. Interfacecharacter(global)TA14. Interfacecharacter(global)TB15. Interfacecharacter(global)TC16. InterfacecharacterTD17. Interfacecharacter(specific)parameters to calculate thework etuparameters to calculate theprogramming voltage andcurrentparameters to calculate theextra guardtime requestedby the card; no extraguardtime is used to sendcharacters from the card tothe MEprotocol type; indicator forthe presence of interfacecharacters, specifying rulesto be used for transmissionswith the given protocol typeoptionaloptionaloptionaloptionala) alwaysa) evaluation by the MEb) reaction by the MEb) using appropriate conventiona) alwaysb) identifying the subsequentcharacters accordinglya) always if presentb) if TA1 is not '11', PTS procedureshall be used (see subclause 5.8.2)a) always if presentb) if PI1 is not 0, then reject the SIM (inaccordance with subclause 5.10)a) always if presentb) if TC1 is neither 0 nor 255, then reject theSIM (in accordance with subclause 5.10); seethe note after the tablea) always if presentnot used for protocol T=0 optional a) optionalb) identifying the subsequent charactersaccordinglyb) --------TA28. Interfacecharacter(global)parameter to calculate theprogramming voltageneverthe allowed value of TB1 above defines that anexternal programming voltage is not applicableTB29. Interfacecharacter(specific)parameters to calculate thework waiting timeoptionala) always if presentb) using the work waiting time accordinglyTC210. InterfacecharacterTDi(i>1)protocol type; indicator forthe presence of interfacecharacters, specifying rulesto be used for transmissionswith the given protocol typeoptionala) always if presentb) identifying the subsequent charactersaccordingly(continued)ETSI
Page 1: TS 100 977 V6.2.0 (1999-05)Technica
Page 4 and 5: (GSM 11.11 version 6.2.0 Release 19
Page 12 and 13: CIVILZSÁMBÉKI POLGÁR„ A kis J
Page 54: (GSM 11.11 version 6.2.0 Release 19
Page 69 and 70:
(GSM 11.11 version 6.2.0 Release 19
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
show all

GSM 11.11 version 6.2.0 - TTFN Smart card pages

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?