SDSPR101 Polycell - 3 in 1 Mouldkiller 2 - Toolbank

11. TOXICOLOGICAL INFORMATIONThere is no data available on the product itself. The product has been assessed following the conventional method in the CHIP Regulations and isclassified for toxicological hazards accordingly. This takes into account, where known, delayed and immediate effects and also chronic effects ofcomponents from short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact. See Sections 2 and 15 fordetails of the resulting hazard classification.Over-exposures of vapour are irritating to eyes and respiratory system. Excessive concentrations may produce effects on the central nervoussystem including drowsiness. In extreme cases loss of consciousness may result. Long term exposure to vapour concentrations in excess ofquoted OELs may result in adverse health effects. Splashes entering the eye will cause discomfort and possible damage. Prolonged contact withthe skin may have a defatting effect which may lead to skin irritation and in some cases dermatitis.12. ECOLOGICAL INFORMATIONThere is no specific data available on the product itself.The product should not be allowed to enter drains or watercourses or be deposited where it can affect ground or surface waters.The Air Pollution Control requirements of regulations made under the Environmental Protection Act may apply to the use of this product.Products classified as Marine Pollutants are indicated as such under Transport (section 14).Products classified as Dangerous For the Environment are indicated as such in sections 2 and 15.Any substances in the product that are classified as Dangerous for the Environment, present at concentrations above those requiring listing aregiven in section 3.13. DISPOSAL CONSIDERATIONSWastes, including emptied containers, should be disposed of in accordance with national regulations.CODES ACCORDING TO THE LIST OF WASTES REGULATIONS:Product as supplied: Assigned as hazardous waste code 03 02 05* other wood preservatives containing dangerous substances.Part-used containers, containing dried residues of the supplied product: Not Applicable.Used containers, rigorously scraped out and containing dried residues of the supplied product: Assigned as non-hazardous waste code 15 01 02plastic packaging OR non-hazardous waste code 15 01 04 metal packaging."Rigorously scraped out" means removing the maximum amount of product from the container by physical or mechanical means (draining orscraping) to leave a residue or contamination that cannot be removed by such means.These codes have been assigned based on the actual composition of the product both as supplied and as dried residues. If mixed with otherwastes, the waste codes quoted may not be applicable.14. TRANSPORT INFORMATIONTransport within user's premises:Always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to doin the event of an accident or spillage.Transport to be in accordance with ADR for road, IMDG for sea. The transport classifications provided in this section are notvalid for transport by Air. Please call the number in section 1 of this safety data sheet to obtain more information on this productsclassification for Air transport.ADR Classification InformationIMDG Classification InformationUN Number : 0000 UN Number : 0000Proper Shipping Name : NOT APPLICABLE Proper Shipping Name : NOT APPLICABLEHazard Class : EX Hazard Class : EXSub-Hazard Class : Sub-Hazard Class :Packing Group : EX Packing Group : EXSDSPR101 Polycell – 3 in 1 Mould Killer Page 5Revision 09/2009

Technical Name (NOS only) : Technical Name (NOS only) :Ltd Qty Code : Ltd Qty Maximum :Packing Instructions : Packing Instructions :Marine Pollutant if indicatedhere:Emergency Schedule No :Flashpoint :NON FLASHSDSPR101 Polycell – 3 in 1 Mould Killer Page 6Revision 09/2009

15. REGULATORY INFORMATIONThis product has been assessed under the CHIP and Control of Pesticides Regulations and is classified as follows:NAMED SUBSTANCESCHIP Regulations:: NilControl of Pesticides Regulations:: BENZALKONIUM CHLORIDE 2.25%W/W (22.5g/l)INDICATION(S) OF DANGERNoneSYMBOLS LETTER(S)NoneWARNING LABEL PHRASES:Statutory conditions relating to use:USE ONLY AS A SURFACE BIOCIDEAPPLICATION RATE: APPROXIMATELY 1 LITRE PER 4 m 2 .Wear suitable protective clothing and suitable gloves.Do not breathe spray.DO NOT CONTAMINATE FOODSTUFFS, EATING UTENSILS OR FOOD CONTACT SURFACES.This material and its container must be disposed of in a safe way.UNPROTECTED PERSONS AND ANIMALS SHOULD BE KEPT AWAY FROM TREATED AREAS FOR 48 HOURS ORUNTIL SURFACES ARE DRY.COVER ALL WATER STORAGE TANKS before application.DO NOT USE NEAR DRAINS, PREVENT ANY SURFACE RUN-OFF FROM ENTERING DRAINS.REMOVE OR COVER ALL FISH TANKS AND BOWLS before application.This product contains substances which are known to be hazardous to the environment. Do not contaminate ground, waterbodiesor watercourses with chemicals or used container.ADDITIONAL PRECAUTIONS FOR PROFESSIONAL OPERATORS:The (COSHH) Control of Substances Hazardous to Health Regulations 2002 may apply to the use of this product at work.Engineering control of operator exposure must be used where reasonably practicable in addition to the following items ofpersonal protective equipment. However, engineering controls may replace personal protective equipment if a COSHHassessment shows they provide an equal or higher standard of protection.AVOID EXCESSIVE CONTAMINATION OF COVERALLS AND LAUNDER REGULARLY.READ ALL PRECAUTIONS BEFORE USE. HSE No. 6157Precautions:WASH ANY CONTAMINATION from skin or eyes immediately.WASH HANDS AND EXPOSED SKIN before meals and after use.Keep only in the original container. Keep container tightly closed. KEEP IN A SAFE PLACE.Keep out of the reach of children.Some local authorities have special facilities for disposal of waste product.Do not use or store by hanging on a hook.Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they maycontain harmful lead.For further advice contact ICI Paints.This product is approved under The Control of Pesticides Regulations 1986 for use as directed. HSE No. 6157.SDSPR101 Polycell – 3 in 1 Mould Killer Page 7Revision 09/2009

16. OTHER INFORMATIONText for R Phrases shown in section 3 describing each ingredient:R21/22 Harmful in contact with skin and if swallowed.R34R50Causes burns.Very toxic to aquatic organisms.The information in this safety data sheet is required in pursuant to the CHIP Regulations.You should satisfy yourself that your COSHH Assessment is in accordance with the COSHH Regulations and Approved Code ofPractice. ICI does not accept any responsibility for your COSHH Assessment. Other Reference: The Control of SubstancesHazardous to Health Regulations (COSHH).The information on this sheet is not a specification: it does not guarantee specific properties. The information is intended toprovide general guidance as to health and safety based upon our knowledge of the handling, storage and use of the product. It isnot applicable to unusual or non-standard uses of the product nor where instructions and recommendations are not followed.We will be pleased to answer any specific enquiries regarding the safe use, storage and handling of our product.Contact: ICI Paints AkzoNobel Technical Group, Wexham Road, Slough, Berks. SL2 5DS. Telephone: 0870 242 1100.Imperial Chemical Industries Limited is part of AkzoNobelRegistered office 26th Floor Portland House Bressenden Place London SW1E 5BG Registered number 218019REVISION 09/2009: CHANGES TO SECTIONS 1,2,3,9,15,16 COMPARED WITH PREVIOUS VERSION DATED 02/2007WHICH IS NOW SUPERSEDED.SDSPR101 Polycell – 3 in 1 Mould Killer Page 8Revision 09/2009