Clipsal StarServe - Installation Guide, 11635

More documents

Recommendations

Info

SECTION 12Troubleshooting GuidesTV Reception Troubleshooting Guide - Free to Air Picture1 Good quality signal strength at antenna inputDo you have a good quality signal strength of 69-89dBuV at theantenna input?You must start with a quality TV signal before you try to distribute it toother TVs. The Clipsal StarServe ® VDU distributes the incoming TV signal tomultiple outlets - good quality in, means good quality out.SIGNAL IN69-89dBuVFor diffi cult reception areas you may require a TV antenna specialistinstaller to give you a quality signal of 72dBuV at the antenna input.2 Output signal from VDUIs the output signal from the VDU set at 72dBuV?Use the variable gain control to adjust the output signal strength to 72dBuV.For diffi cult reception areas you may require a TV antenna specialistinstaller to give you a quality signal of 72dBuV at the antenna input.SIGNAL OUT72dBuV78 INSTALLATION GUIDE
SECTION 12Troubleshooting Guides3 Modulatorsignal strengthIs the modulator signal strengthwithin 15dBuV of the VDUoutput signal strength?Lower signals may give a goodpicture quality to TV outlets butwhen a modulator is introduced intothe system and the difference insignal strength is more than 15dBuVthe picture quality will deteriorate.For diffi cult reception areasyou may require a TV antennaspecialist installer to give you aquality signal of 72dBuV at theantenna input.MODINPUT B85dBuVANTENNAOUTPUT72dBuVTV Reception Troubleshooting Guide - Modulated ChannelsModulated AV equipment channels are not clear?Are the modulated channels at least 2 channels apart from any free to airTV channels being broadcasted in your area?• Set the channels more than two channels apart from each other• Check the TV Across Australia book for channels being broadcastin your area.Do the Modulated channels have at least two channel separation?• Example: CH A = UHF 35 CH B = 37 etc…• Set the channels more than two channels apart from each other.If you are using Y Leads or double adaptors and the picture seems to be washedout, you must make sure that the Hi-Z dip switches are in the Hi-Z position.The reason for this is the Hi-Z dip switches ensure the impedance of leads arekept consistent with the requirements for video distribution.INSTALLATION GUIDE79
Page 1:
INSTALLATION GUIDEHomeNetworkingSol
Page 4 and 5:
SECTION 1 What is Clipsal StarServe
Page 6 and 7:
SECTION 2Introduction to MATV Basic
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
SECTION 3Clipsal StarServe ® Produ
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 25 and 26:
Page 27 and 28: SECTION 3Clipsal StarServe ® Produ
Page 33 and 34: SECTION 4Minimum TV Cabling Require
Page 41 and 42: SECTION 5Video Distribution - How t
Page 55 and 56: SECTION 6Phone/Data Minimum Cabling
Page 57 and 58: SECTION 7Telephone/Internet - How t
Page 63 and 64: SECTION 8Data Cabling - How to Conn
Page 65 and 66: SECTION 9Subscription TV Cabling Re
Page 67 and 68: SECTION 9Subscription TV Cabling Re
Page 69 and 70: SECTION 10Cabling ConsiderationsKey
Page 71 and 72: SECTION 10Cabling ConsiderationsKey
Page 73 and 74: SECTION 11Clipsal Audio SolutionsIn
Page 75 and 76: SECTION 11Clipsal Audio SolutionsCl
Page 77: SECTION 12Troubleshooting GuidesInf
Page 81 and 82: SECTION 13Clipsal StarServe ® FAQs
Page 84: INSTALLATION GUIDECLIPSAL STARSERVE
show all

Clipsal StarServe - Installation Guide, 11635

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?