Clipsal StarServe - Installation Guide, 11635
Clipsal StarServe - Installation Guide, 11635 Clipsal StarServe - Installation Guide, 11635
SECTION 3Clipsal StarServe ® Product IntroductionModulatorsModulators connect active devices such as your subscription TV decoder and DVD player so that they can be distributedto all other TV outlets connected to Clipsal StarServe ® . The modulator converts video composite signals into analogueUHF frequencies. Your TV or tuner must be able to receive analogue frequencies for modulated channels.8071VMP – Single Channel ModulatorSingle channel modulators will distribute one device to any TV connected to Clipsal StarServe ® . A single channelmodulator is generally used for the distribution of surveillance cameras at the front door.8072VMPIR – 2 Channel ModulatorTwo channel modulators will distribute two devices such as subscription TV and a DVD player. This model is IR enabled toallow for the remote controlling of devices in other rooms over the coax cable. Up to four devices can be controlled usingdual emitter leads.8074VMPIR – 4 Channel ModulatorFour channel modulators will distribute four devices such as subscription TV, DVD, video and a digital set top box toall outlets connected to Clipsal StarServe ® .This model is IR enabled to allow for the remote controlling of devices in other rooms over the coax cable. Up to eightdevices can be controlled using dual emitter leads.Modulator locatedin your MAINENTERTAINMENT AREA26 INSTALLATION GUIDE
SECTION 3Clipsal StarServe ® Product IntroductionEmitter LeadsInfrared emitter leads are placed on the IR receiver of the device you wish to control. There is a sticky backingprovided on the reverse side of the lead which attaches easily to the device.8050LDSingle Emitter Lead8050/2LDDouble Emitter LeadConnect the leads to the modulator located in theMAIN ENTERTAINMENT AREA (the lounge room)Infrared TargetsAn infrared target is required for EACH ROOM you wish to remotely control devices from. Simply place it in aconvenient location either alongside or underneath the TV.8050TRInfrared Transmitter8050TTTube Target8050FTFlat Target8050STShelf Target8000INJIR Injector(Refer PAGE 30)The IR target can be connected to any TV outlet in any room.The 8050TT, 8050ST and 8050FT are connected using the 8000INJ IR injector.INSTALLATION GUIDE27
- Page 1: INSTALLATION GUIDEHomeNetworkingSol
- Page 4 and 5: SECTION 1 What is Clipsal StarServe
- Page 6 and 7: SECTION 2Introduction to MATV Basic
- Page 8 and 9: SECTION 2Introduction to MATV Basic
- Page 10 and 11: SECTION 2Introduction to MATV Basic
- Page 12 and 13: SECTION 3Clipsal StarServe ® Produ
- Page 14 and 15: SECTION 3Clipsal StarServe ® Produ
- Page 16 and 17: SECTION 3Clipsal StarServe ® Produ
- Page 18 and 19: SECTION 3Clipsal StarServe ® Produ
- Page 20 and 21: SECTION 3Clipsal StarServe ® Produ
- Page 22 and 23: SECTION 3Clipsal StarServe ® Produ
- Page 25: SECTION 3Clipsal StarServe ® Produ
- Page 29 and 30: SECTION 3Clipsal StarServe ® Produ
- Page 31 and 32: SECTION 3Clipsal StarServe ® Produ
- Page 33 and 34: SECTION 4Minimum TV Cabling Require
- Page 37 and 38: SECTION 4Minimum TV Cabling Require
- Page 39 and 40: SECTION 4Minimum TV Cabling Require
- Page 41 and 42: SECTION 5Video Distribution - How t
- Page 43 and 44: SECTION 5Video Distribution - How t
- Page 45 and 46: SECTION 5Video Distribution - How t
- Page 47 and 48: SECTION 5Video Distribution - How t
- Page 49 and 50: SECTION 5Video Distribution - How t
- Page 51 and 52: SECTION 5Video Distribution - How t
- Page 53 and 54: SECTION 5Video Distribution - How t
- Page 55 and 56: SECTION 6Phone/Data Minimum Cabling
- Page 57 and 58: SECTION 7Telephone/Internet - How t
- Page 59 and 60: SECTION 7Telephone/Internet - How t
- Page 61 and 62: SECTION 7Telephone/Internet - How t
- Page 63 and 64: SECTION 8Data Cabling - How to Conn
- Page 65 and 66: SECTION 9Subscription TV Cabling Re
- Page 67 and 68: SECTION 9Subscription TV Cabling Re
- Page 69 and 70: SECTION 10Cabling ConsiderationsKey
- Page 71 and 72: SECTION 10Cabling ConsiderationsKey
- Page 73 and 74: SECTION 11Clipsal Audio SolutionsIn
- Page 75 and 76: SECTION 11Clipsal Audio SolutionsCl
SECTION 3<strong>Clipsal</strong> <strong>StarServe</strong> ® Product IntroductionEmitter LeadsInfrared emitter leads are placed on the IR receiver of the device you wish to control. There is a sticky backingprovided on the reverse side of the lead which attaches easily to the device.8050LDSingle Emitter Lead8050/2LDDouble Emitter LeadConnect the leads to the modulator located in theMAIN ENTERTAINMENT AREA (the lounge room)Infrared TargetsAn infrared target is required for EACH ROOM you wish to remotely control devices from. Simply place it in aconvenient location either alongside or underneath the TV.8050TRInfrared Transmitter8050TTTube Target8050FTFlat Target8050STShelf Target8000INJIR Injector(Refer PAGE 30)The IR target can be connected to any TV outlet in any room.The 8050TT, 8050ST and 8050FT are connected using the 8000INJ IR injector.INSTALLATION GUIDE27