Nitrogen Gas Springs and Accessories - Electronic Fasteners Inc

More documents

Recommendations

Info

RVPneumatic VibratorThe Raymond Pneumatic Vibrator is an idealsolution for removing punchings, trimmings andscrap produced during press operations. Theautomatic and continuous removal keeps thepress operator from interrupting production toclean away the punchings, trimmings and/orscraps by hand. The vibrator uses a pneumaticpower source offering a cost effective alternativeto electrically driven conveyor belts.The pneumatic power source allows this unitto work in areas contaminated by lubricatingfluids and oils. Unlike electrically driven systemswith their inherent shock hazard, the RaymondPneumatic Vibrator is safe to use as it consumesno electricity.The compact design of the unit is made forworking in the tight areas which are present onsome presses. Easy to install, simply select thearea for the unit, bolt in place and connect it toyour air supply. The low air consumption andsilent running Raymond Pneumatic Vibrator isthe safe and economical solution for your scrapremoval needs.All units feature a standard NPT connectionfor easy hookup to lubricated shop air and anadjustable exhaust muffler. By varying the inputpressure and exhaust flow, the cycle rate andstroke of the unit can be custom adjusted bythe user in each application. Note that if a lubricatoris not used in conjunction with the shopair, the piston rod of the vibrator unit should belubricated monthly.Standard transport trays are available. Forbalanced performance, all trays should use theRV12-S, RV25-S or RV50-S adjustable supportsshown on page 40. For proper scrapremoval, the tray should be sloped at an angleof 8 degrees or greater. The exact amount ofinclination should be adjusted on-site basedupon the scrap weight and shape as well as theamount of oil and grease that is likely to bepresent.Sloping of the tray can be accomplished bymounting the tray parallel to the vibrator unitand sloping both the vibrator and the tray.Alternately, the tray can be mounted at an anglewith respect to the unit. In both cases, careshould be taken to assure that the tray supportsare used and are in contact with the traythrough the entire range of motion.Mounting method with the tray parallel to the vibrator unit.Mounting method with only the tray sloped. Note the useof flats on the base of the tray for proper contact with thesupports.
Raymond ®Ordering Information — RV 3 through RV 9OrderNumber A B C D E F G H I J K LRV 3 128 / 5.04 90 / 3.54 48 / 1.89 80 / 3.15 70 / 2.76 44 / 1.73 38 / 1.50 19 / .75 95 / 3.74 70 / 2.76 49 / 1.93 12 / .47RV 5 155 / 6.10 100 / 3.94 65 / 2.56 90 / 3.54 80 / 3.15 60 / 2.36 55 / 2.17 27 / 1.06 118 / 4.65 82 / 3.23 60 / 2.36 12 / .47RV 7 158 / 6.22 122 / 4.80 88 / 3.47 100 / 3.94 100 / 3.94 80 / 3.15 78 / 3.07 36 / 1.42 118 / 4.65 104 / 4.09 60 / 2.36 12 / .47RV 9 179 / 7.05 150 / 5.91 108 / 4.25 120 / 4.72 125 / 4.92 98 / 3.86 95 / 3.74 48 / 1.89 130 / 5.12 130 / 5.12 65 / 2.56 14 / .55OrderNumber M N O P S T V X Y ZRV 3 14 / .55 12.5 / .49 41 / 1.61 39 / 1.54 10 / .39 14 / .55 9 / .35 5 / .20 38 / 1.50 16 / .63RV 5 15 / .59 19 / .75 47 / 1.85 49 / 1.93 12 / .47 14 / .55 9 / .35 8 / .32 48 / 1.89 16 / .63RV 7 15 / .59 19 / .75 47 / 1.85 49 / 1.93 14 / .55 14 / .55 9 / .35 9 / .35 64 / 2.52 16 / .63RV 9 20 / .79 24 / .95 52 / 2.05 56 / 2.21 18 / .71 17 / .67 11 / .43 11 / .43 75 / 2.95 23 / .91Technical DataAir Typical Air Typical Piston Typical Maximum Noise WorkingOrder Fitting Air Consumption Piston Speed Mounting Load Level TemperatureNumber Female NPT Pressure (ft 3 / min) Stroke (ft/min) Inclination Inc. Tray (dB-A) (°F)RV 3 1/8 70 1.1 30 / 1.18 26-32 8° 13.2 50 32 -158RV 5 1/4 70 2.1 33 / 1.30 26-32 8° 30.9 50 32 -158RV 7 1/4 70 5.1 20 / .79 26-32 8° 79.4 50 32 -158RV 9 3/8 70 7.6 28 / 1.10 26-32 8° 123.5 53 32 -158Dimensions in millimeters / inches
Page 1: Raymond®Nitrogen Gas Springs and A
Page 5 and 6: Raymond ®RD-19Disposable Mini Spri
Page 7 and 8: Raymond ®RD-150Disposable Mini Spr
Page 9 and 10: Raymond ®REStripper Springs — Se
Page 11 and 12: Ordering Information — RCT 300 th
Page 13 and 14: Mounting plate “J” for Models R
Page 15 and 16: Model TRaymond ®All Threaded (Also
Page 17 and 18: Ordering Information — RG-750 thr
Page 19 and 20: Mounting plate “J” for Models R
Page 21 and 22: Mounting Arrangements for RG 750 th
Page 23 and 24: Ordering Information — RS-1000 th
Page 25 and 26: RH 500 through RH 2200 cont.Flange
Page 27 and 28: Raymond ®Control PanelOrder No. SP
Page 29 and 30: Hose Fittings — 9/16"-18" — O-R
Page 31 and 32: Flange Stripper Top MountRaymond ®
Page 33 and 34: RW-R Roller Cam Wedge UnitRaymond
Page 35 and 36: RW-A Roller Cam Wedge UnitRaymond
Page 37 and 38: Raymond ®RRRoller CamRaymond Rolle
Page 39: Model RR 15 Roller CamRaymond ®Ord
Page 43 and 44: Raymond ®RPPneumatic Pin Extractor
Page 45 and 46: Spare Parts and AccessoriesRaymond
Page 47 and 48: Typical Applications for Nitrogen G
Page 49 and 50: How to OrderNitrogen Gas SpringsOrd
Page 51 and 52: NotesRaymond ®

Nitrogen Gas Springs and Accessories - Electronic Fasteners Inc

Create successful ePaper yourself

Delete template?

Save as template?