1. outline - toshiba tec europe
1. outline - toshiba tec europe 1. outline - toshiba tec europe
1. OUTLINE EO10-13009A1.6 ELECTRONIC SPECIFICATIONS(iii) Connector DescriptionPin Source Compatibility mode Nibble Mode1 Host Nstrobe HostCLK2 Host/Ptr Data0(LSB) Data0(LSB)3 Host/Ptr Data1 Data14 Host/Ptr Data2 Data25 Host/Ptr Data3 Data36 Host/Ptr Data4 Data47 Host/Ptr Data5 Data58 Host/Ptr Data6 Data69 Host/Ptr Data7 Data710 Printer Nack PtrClk11 Printer Busy PtrBusy/Data3.712 Printer Perror AckDataReq/Data2.613 Printer Select Xflag/Data1.514 Host nAutoFd HostBusy15 NC NC16 GND GND17 FG FG18 Printer Logic-H Logic-H19 GND GND20 GND GND21 GND GND22 GND GND23 GND GND24 GND GND25 GND GND26 GND GND27 GND GND28 GND GND29 GND GND30 GND GND31 Host nInit NInit32 Printer nFault nDataAvail/Data0.433 GND GWDND GWDNC34 Printer NC NC35 Printer NC NC36 nSelectln 1284-ActiveNC: None connectND: Not definedApplicable connector: Printer side: 57RE-40360 (AMPHENOL type or equivalent)Cable side: 57-30360 (AMPHENOL type or equivalent)NOTE:The initial letter “n” of the signal indicates a “L” active signal. Bi-directional datatransmission is possible with all the above signals.Be sure to use the twisted pair lines for each signal, and connect the return side to thesignal ground level.1-18
1. OUTLINE EO10-13009A1.6 ELECTRONIC SPECIFICATIONS(iv) Input/Output signal(1) Input signal to the printer• DATA: 8-bit parallel signal (positive logic)• STB: Strobe signal to capture 8-bit data (negative logic)• RESET: A signal to reset the printer (negative logic)• SELECT IN: A signal which goes high when the printer is transmitted to IEEE1284mode(2) Output signal from the printer• ACK: 8-bit data request signal and pulse signal that is output as the lastBUSY signal (negative logic)• BUSY: This signal indicates that the printer is in BUSY status. Input the newdata when the level is low. (positive logic)• FAULT: This signal goes low when the printer is in alarm status. At this time,all control circuit in the printer is stopped. (negative logic)• PE: This signal indicates that the paper roll runs out or is near to end.(positive logic)• Select: When the switch is opened, this signal goes high. When the switch isshort, this signal goes low.(3) Power supply• +5V DC:• GND:5VCommon ground on the circuit(v) Electronic Characteristics(1) Input signal level (STBTTL, DATA1Ω8)• All input signal is C-MOS level.• High level: Min. 3.8V• Low level: Max. 1.1V(2) Output signal level• All output signal is C-MOS level.• High level: Min. 2.4V• Low level: Max. 0.4V1-19
- Page 1: TOSHIBA REMOTE RECEIPT PRINTERTRST-
- Page 4 and 5: 1. OUTLINE EO10-13009A(Revision Dat
- Page 6 and 7: 1. OUTLINE EO10-13009A1.3 OVERVIEW
- Page 8 and 9: 1. OUTLINE EO10-13009A1.3 OVERVIEW
- Page 11 and 12: 1. OUTLINE EO10-13009A1.6 ELECTRONI
- Page 13 and 14: 1. OUTLINE EO10-13009A1.6 ELECTRONI
- Page 15 and 16: 1. OUTLINE EO10-13009A1.6 ELECTRONI
- Page 17 and 18: 1. OUTLINE EO10-13009A1.6 ELECTRONI
- Page 19: 1. OUTLINE EO10-13009A1.6 ELECTRONI
- Page 23 and 24: 1. OUTLINE EO10-13009A(Revision Dat
- Page 25 and 26: 1. OUTLINE EO10-13009A1.8 DC POWER
- Page 27 and 28: 2. SUPPLY SPECIFICATIONS EO10-13009
- Page 29: 2. SUPPLY SPECIFICATIONS EO10-13009
<strong>1.</strong> OUTLINE EO10-13009A<strong>1.</strong>6 ELECTRONIC SPECIFICATIONS(iii) Connector DescriptionPin Source Compatibility mode Nibble Mode1 Host Nstrobe HostCLK2 Host/Ptr Data0(LSB) Data0(LSB)3 Host/Ptr Data1 Data14 Host/Ptr Data2 Data25 Host/Ptr Data3 Data36 Host/Ptr Data4 Data47 Host/Ptr Data5 Data58 Host/Ptr Data6 Data69 Host/Ptr Data7 Data710 Printer Nack PtrClk11 Printer Busy PtrBusy/Data3.712 Printer Perror AckDataReq/Data2.613 Printer Select Xflag/Data<strong>1.</strong>514 Host nAutoFd HostBusy15 NC NC16 GND GND17 FG FG18 Printer Logic-H Logic-H19 GND GND20 GND GND21 GND GND22 GND GND23 GND GND24 GND GND25 GND GND26 GND GND27 GND GND28 GND GND29 GND GND30 GND GND31 Host nInit NInit32 Printer nFault nDataAvail/Data0.433 GND GWDND GWDNC34 Printer NC NC35 Printer NC NC36 nSelectln 1284-ActiveNC: None connectND: Not definedApplicable connector: Printer side: 57RE-40360 (AMPHENOL type or equivalent)Cable side: 57-30360 (AMPHENOL type or equivalent)NOTE:The initial letter “n” of the signal indicates a “L” active signal. Bi-directional datatransmission is possible with all the above signals.Be sure to use the twisted pair lines for each signal, and connect the return side to thesignal ground level.1-18
Change language