Download manual
Download manual Download manual
SYSTEMA S.p.A.4.2 Assembling the unitAIRTIGHT GAS-FIRED RADIANT TUBES INFRATo assemble the various components that make up theINFRA radiant module, please follow the instructionsgiven below.Begin assembling the tubes, starting with the curvedone:1) Fit the two tubes (delivery and return) into the curveby about 120 mm, hammering slightly if required,taking care to place a piece of wood between thehammer and sleeve (see fig. 18a). Then fix them inplace using the screws supplied with the curve.2a) If Infra 9B and 12B models are used, assemble thetwo sleeves Ø 108mm and Ø80mm, fixing themwith the supplied screws, taking care to push thetubes half way into the sleeve (app. 150 mm), hammeringslightly if required, taking care to place apiece of wood between the hammer and sleeve(see (fig. 18a).2b) If the Infra 6B model is used, assemble the burnerunion and aspirator union as shown in the diagram(fig. 4 page 12), the fixing holes of the aspirator andburner must be positioned vertically as shown in fig.21.3) Fit the other 2 tubes, taking care that the ends withsellotape are positioned at opposite ends to thesleeves (fig. 4 page 12).Fig.17Fig.18WoodFig.18aFig.19Rev. 18GB061024
AIRTIGHT GAS-FIRED RADIANT TUBES INFRASYSTEMA S.p.A.Fig.20HOLEUNIONHOLEBAF BURNERFig. 21 Vertical position of the holeson the aspirator and burner unionsIn Infra 9B a 12B you have to block the pipe 108Ø givingenough space in order to install the Burner Baf lockingFig.21aThe first bracket must be positionedas shown in detail A(fig.23)The intermediate bracketsonly have the bottom elementFig. 22 Assembling the INFRA module: fixing the brackets25Rev. 18GB0610
- Page 1 and 2: AIRTIGHT GAS-FIRED RADIANT TUBESINF
- Page 3 and 4: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 5 and 6: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 7 and 8: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 9 and 10: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 11 and 12: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 13 and 14: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 15 and 16: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 17 and 18: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 19 and 20: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 21 and 22: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 23: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 27 and 28: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 29 and 30: SYSTEMA S.p.A.AIRTIGHT GAS-FIRED RA
- Page 31 and 32: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 33 and 34: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 35 and 36: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 37 and 38: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 39 and 40: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 41 and 42: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 43 and 44: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 45 and 46: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 47 and 48: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 49 and 50: SYSTEMA S.p.A.AIRTIGHT GAS-FIRED RA
- Page 51 and 52: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 53 and 54: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 55 and 56: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 57 and 58: AIRTIGHT GAS-FIRED RADIANT TUBES IN
- Page 59: AIRTIGHT GAS-FIRED RADIANT TUBES IN
SYSTEMA S.p.A.4.2 Assembling the unitAIRTIGHT GAS-FIRED RADIANT TUBES INFRATo assemble the various components that make up theINFRA radiant module, please follow the instructionsgiven below.Begin assembling the tubes, starting with the curvedone:1) Fit the two tubes (delivery and return) into the curveby about 120 mm, hammering slightly if required,taking care to place a piece of wood between thehammer and sleeve (see fig. 18a). Then fix them inplace using the screws supplied with the curve.2a) If Infra 9B and 12B models are used, assemble thetwo sleeves Ø 108mm and Ø80mm, fixing themwith the supplied screws, taking care to push thetubes half way into the sleeve (app. 150 mm), hammeringslightly if required, taking care to place apiece of wood between the hammer and sleeve(see (fig. 18a).2b) If the Infra 6B model is used, assemble the burnerunion and aspirator union as shown in the diagram(fig. 4 page 12), the fixing holes of the aspirator andburner must be positioned vertically as shown in fig.21.3) Fit the other 2 tubes, taking care that the ends withsellotape are positioned at opposite ends to thesleeves (fig. 4 page 12).Fig.17Fig.18WoodFig.18aFig.19Rev. 18GB061024