I&O Manual - Solaris Water Heaters - Categories On Thermal ...
I&O Manual - Solaris Water Heaters - Categories On Thermal ... I&O Manual - Solaris Water Heaters - Categories On Thermal ...
SEE TABLE 0Figure 8: Separate Horizontal – Vent/Air Intake Terminal Configuration16
H. Separate Vertical Venting System - See Figures 9, 10, and 11.Vertical Venting –1. Do not exceed maximum vent lengths. Refer toTable 0.2. Slope horizontal runs minimum ¼ inch per footdown towards water heater.3. Install fire stops where vent passes through floors,ceilings or framed walls. The fire stop must closethe opening between the vent pipe and the structure.Fire stop manufacturers are Air-Jet, American MetalProducts, Metal-Fab, and Simpson Dura-Vent.4. Whenever possible, install vent straight through theroof. Refer to Figure 9 if offset is necessary. Maintainminimum clearance to combustiblematerials.5. Install Vent Terminal.a. Size roof opening to maintain minimum clearancefrom combustible materials.b. Extend vent pipe to maintain minimum verticaland horizontal distance of twelve (12) inchesfrom roof surface. Allow additional vertical distancefor expected snow accumulation. Providebrace as required. Refer to Figure 11.c. Vertical venting requires use of the roof flashingand storm collar to prevent moisture from enteringthe structure.d. Install storm collar on vent pipe immediatelyabove flashing. Apply Dow Corning Silastic 732RTV Sealant between vent pipe and storm collarto provide weathertight seal.e. Attach vent terminal.Vertical Air Intake Piping –1. Do not exceed maximum air intake length. Refer toTable 0.2. Locate air intake termination on the same roof locationas the vent termination if possible, to preventnuisance water heater shutdowns. However, waterheater may be installed with vertical venting andsidewall combustion air inlet or vice versa, if installationconditions do not allow alternate arrangement.3 Use single wall metal pipe and fittings or thin wallPVC available at most heating distributors.4. Air intake termination must be located:Vertical - At least twelve (12) inches above the roofsurface plus the expected snow accumulation.5. Start at collar on burner enclosure (inside waterheater jacket) and work towards the air intake terminal.6. Maintain minimum of 1/4 inch per foot slope onhorizontal runs. Slope down towards water heater.7. The air intake pipe must be adequately supportedwith straps or supports no less than five (5) feetapart on horizontal runs. The complete air intakepiping system must be rigid and able to withstandminor impacts without collapse.8. Inlet air pipe penetration:Vertical - Size roof opening to allow easy insertionof inlet piping and allow proper installation of flashingand storm collar.a. Use appropriately designed vent flashing whenpassing through roofs. Follow flashing manufacturers’instructions for installation procedures.Flashing manufacturers are Air-Jet, AmericanMetal Products, Metal Fab, and Simpson Dura-Vent.b. Extend air intake pipe to maintain minimumvertical and horizontal distance of twelve (12)inches from roof surface. Allow additional verticaldistance for expected snow accumulation.Provide brace as required. Refer to Figure 11.c. Vertical air intake requires flashing and a stormcollar to prevent moisture from entering thestructure.d. Install storm collar on air intake pipe immediatelyabove flashing. Apply Dow Corning Silastic732 RTV Sealant between air intake pipe andstorm collar to provide weathertight seal.9. Seal all joints airtight, using silicone caulk or self -adhesive aluminum tape.10. Install Air Intake Terminal:Vertical - Insert intake piping into intake terminalcollar. Secure terminal to intake piping and sealjoint with silicone caulk.17
- Page 1 and 2: INSTALLATION, OPERATING ANDSERVICE
- Page 3 and 4: WARNINGThis water heater requires r
- Page 5 and 6: WaterheaterModelNumberINPUT(MBH)GRO
- Page 7 and 8: 5. For water heater located in an u
- Page 9 and 10: B. General Guidelines1. Vent system
- Page 12 and 13: 12Figure 4: Recommended Separate Ho
- Page 14 and 15: E. Optional Separate Horizontal Ven
- Page 18 and 19: 18Figure 9: Vertical Vent Installat
- Page 20 and 21: IV. Water Piping and Trim1. WATER T
- Page 22 and 23: escape of air trapped in the water
- Page 24 and 25: 24Figure 13: Safety & Drain Valve I
- Page 26 and 27: Table 5: Maximum Capacity of Schedu
- Page 28 and 29: SolarisLadder DiagramNOTES:1. IF LO
- Page 30 and 31: VII. Modular InstallationA. General
- Page 32 and 33: Figure 17: Modular Water heater Con
- Page 34 and 35: VIII. System Start-upA. Safe operat
- Page 36 and 37: FOR YOUR SAFETY READ BEFORE OPERATI
- Page 38 and 39: Figure 22: SOL500-1500 Pilot Valve1
- Page 40 and 41: Secondsfor OneRevolutionTable 7:
- Page 42 and 43: A. General Guidelines1. A thorough
- Page 44 and 45: I. Check Combustion and Safety Cont
- Page 46 and 47: C. Trouble Shooting GuideAlarm Mess
- Page 48 and 49: X. Thermal Solutions Water heater C
- Page 50 and 51: Label 101175-04RJ-11(6 pin)Boiler P
- Page 52 and 53: D. SETUP MENUDisplayWWSDLL StartTri
- Page 54 and 55: E. Boiler Configuration MenuDisplay
- Page 56 and 57: G. Setpoints MenuDisplayOperational
- Page 58 and 59: XI. Repair PartsAll Solaris ® Seri
- Page 60 and 61: 63159847311SIDE VIEW OFGAS VALVE102
- Page 62 and 63: 12KeyNo.Manifold Orifice AssemblyDe
- Page 64 and 65: 6 59738412Key No. Description Quant
H. Separate Vertical Venting System - See Figures 9, 10, and 11.Vertical Venting –1. Do not exceed maximum vent lengths. Refer toTable 0.2. Slope horizontal runs minimum ¼ inch per footdown towards water heater.3. Install fire stops where vent passes through floors,ceilings or framed walls. The fire stop must closethe opening between the vent pipe and the structure.Fire stop manufacturers are Air-Jet, American MetalProducts, Metal-Fab, and Simpson Dura-Vent.4. Whenever possible, install vent straight through theroof. Refer to Figure 9 if offset is necessary. Maintainminimum clearance to combustiblematerials.5. Install Vent Terminal.a. Size roof opening to maintain minimum clearancefrom combustible materials.b. Extend vent pipe to maintain minimum verticaland horizontal distance of twelve (12) inchesfrom roof surface. Allow additional vertical distancefor expected snow accumulation. Providebrace as required. Refer to Figure 11.c. Vertical venting requires use of the roof flashingand storm collar to prevent moisture from enteringthe structure.d. Install storm collar on vent pipe immediatelyabove flashing. Apply Dow Corning Silastic 732RTV Sealant between vent pipe and storm collarto provide weathertight seal.e. Attach vent terminal.Vertical Air Intake Piping –1. Do not exceed maximum air intake length. Refer toTable 0.2. Locate air intake termination on the same roof locationas the vent termination if possible, to preventnuisance water heater shutdowns. However, waterheater may be installed with vertical venting andsidewall combustion air inlet or vice versa, if installationconditions do not allow alternate arrangement.3 Use single wall metal pipe and fittings or thin wallPVC available at most heating distributors.4. Air intake termination must be located:Vertical - At least twelve (12) inches above the roofsurface plus the expected snow accumulation.5. Start at collar on burner enclosure (inside waterheater jacket) and work towards the air intake terminal.6. Maintain minimum of 1/4 inch per foot slope onhorizontal runs. Slope down towards water heater.7. The air intake pipe must be adequately supportedwith straps or supports no less than five (5) feetapart on horizontal runs. The complete air intakepiping system must be rigid and able to withstandminor impacts without collapse.8. Inlet air pipe penetration:Vertical - Size roof opening to allow easy insertionof inlet piping and allow proper installation of flashingand storm collar.a. Use appropriately designed vent flashing whenpassing through roofs. Follow flashing manufacturers’instructions for installation procedures.Flashing manufacturers are Air-Jet, AmericanMetal Products, Metal Fab, and Simpson Dura-Vent.b. Extend air intake pipe to maintain minimumvertical and horizontal distance of twelve (12)inches from roof surface. Allow additional verticaldistance for expected snow accumulation.Provide brace as required. Refer to Figure 11.c. Vertical air intake requires flashing and a stormcollar to prevent moisture from entering thestructure.d. Install storm collar on air intake pipe immediatelyabove flashing. Apply Dow Corning Silastic732 RTV Sealant between air intake pipe andstorm collar to provide weathertight seal.9. Seal all joints airtight, using silicone caulk or self -adhesive aluminum tape.10. Install Air Intake Terminal:Vertical - Insert intake piping into intake terminalcollar. Secure terminal to intake piping and sealjoint with silicone caulk.17