I&O Manual - Solaris Water Heaters - Categories On Thermal ...

More documents

Recommendations

Info

E. Optional Separate Horizontal Vent Terminal Mounting – See Figure 61. Do not exceed maximum vent/air intake lengths.Refer to Table 0.2. This installation will allow a maximum of five (5)feet vertical exterior run of the vent/air intake pipingto be installed on separate horizontal venting andindoor air horizontal venting.Note: Exterior run to be included in equivalent vent/air intake lengths.3. Install vent piping.a. Install vent piping for desired venting system.Refer to specific section for details for vent pipeinstallation.b. After penetrating wall/thimble, install a 90°elbow so that elbow leg is in the up direction.c. Install maximum of five (5) feet of vent pipe.Refer to Sections C through E for proper proceduresfor joining vent pipe and fittings.d. At top of vent pipe length install a 90° elbow sothat elbow leg is opposite the building’s exteriorsurface.e. Install 45° elbow to upper 90° elbow so that legof 45° is in down direction (see Figure 6). If notusing indoor air, proceed to Step f.f. Install horizontal vent terminal.g. Brace piping if required.4. Air Intake Piping (not required for indoor air).a. Install air intake piping for desired venting system.Refer to specific section for details for airintake installation.b. After penetrating wall, install a corrosion resistant90 o elbow so that elbow leg is in the updirection.c. Install maximum of five (5) feet of corrosionresistant air intake pipe.d. At top of air intake pipe install air intake terminal(provided with water heater).e. Brace piping if required.14Figure 6: Optional Indoor Air – Vent Terminal Installation
F. Conventional Venting (Negative Draft) – See Figure 71. The minimum chimney height is 15 feet.2. The chimney must be protected from down drafts,rain and debris by using a chimney cap or star.3. Start installing vent at vent cap and continue installationtoward the water heater.4. The flue connector and chimney flue diameter mayneed to be increased or decreased depending onthe dimensions of the water heater. Consult theNational Fuel Gas Code or Local Codes for sizing.<strong>Water</strong> heater input, flue connector lateral distanceand chimney height affect the flue connector orchimney flue diameters.5. A double acting barometric damper with integralflue spillage interlock switch must be used whenthe water heater is vented conventionally.6. The chimney and flue connector must be sizedand configured to provide a minimum - 0.04 inchw.c. draft at the vent outlet of the water heater.7. Maintain a minimum vertical pitch of one (1) inchin four (4) feet of vent connector run.G. Air Intake Piping – See Figure 4 & 81. Locate air intake termination on the same wall asthe vent termination if possible, to prevent nuisancewater heater shutdowns. However, water heatermay be installed with vertical venting and sidewallcombustion air inlet or vice versa, if installationconditions do not allow alternate arrangement.2. Do not exceed maximum air intake length. SeeTable 0.3. Use single wall metal pipe and fittings or thinwall PVC available at most heating distributors.4. Horizontal air intake termination must be locatedat least twelve (12) inches above grade plus theexpected snow accumulation.5. Start at collar on burner enclosure (inside waterheater jacket) and work towards the air intaketerminal.6. Maintain minimum of 1/4 inch per foot slope onhorizontal runs. Slope towards air inlet terminalwhen possible. If not, slope towards water heater.7. The air intake pipe must be adequately supportedwith straps or supports no less than five (5) feetapart on horizontal runs. The complete air intakepiping system must be rigid and able to withstandminor impacts without collapse.8. Inlet air pipe penetration: Horizontal - Size wallpenetration to allow easy insertion of air inletpiping. Seal around pipe with sealant to formweathertight exterior joint.9. Seal all joints airtight, using silicone caulk or selfadhesivealuminum tape.10. Install Air Intake Terminal.Figure 7: Conventional Venting (Negative Draft)15
Page 1 and 2: INSTALLATION, OPERATING ANDSERVICE
Page 3 and 4: WARNINGThis water heater requires r
Page 5 and 6: WaterheaterModelNumberINPUT(MBH)GRO
Page 7 and 8: 5. For water heater located in an u
Page 9 and 10: B. General Guidelines1. Vent system
Page 12 and 13: 12Figure 4: Recommended Separate Ho
Page 16 and 17: SEE TABLE 0Figure 8: Separate Horiz
Page 18 and 19: 18Figure 9: Vertical Vent Installat
Page 20 and 21: IV. Water Piping and Trim1. WATER T
Page 22 and 23: escape of air trapped in the water
Page 24 and 25: 24Figure 13: Safety & Drain Valve I
Page 26 and 27: Table 5: Maximum Capacity of Schedu
Page 28 and 29: SolarisLadder DiagramNOTES:1. IF LO
Page 30 and 31: VII. Modular InstallationA. General
Page 32 and 33: Figure 17: Modular Water heater Con
Page 34 and 35: VIII. System Start-upA. Safe operat
Page 36 and 37: FOR YOUR SAFETY READ BEFORE OPERATI
Page 38 and 39: Figure 22: SOL500-1500 Pilot Valve1
Page 40 and 41: Secondsfor OneRevolutionTable 7:
Page 42 and 43: A. General Guidelines1. A thorough
Page 44 and 45: I. Check Combustion and Safety Cont
Page 46 and 47: C. Trouble Shooting GuideAlarm Mess
Page 48 and 49: X. Thermal Solutions Water heater C
Page 50 and 51: Label 101175-04RJ-11(6 pin)Boiler P
Page 52 and 53: D. SETUP MENUDisplayWWSDLL StartTri
Page 54 and 55: E. Boiler Configuration MenuDisplay
Page 56 and 57: G. Setpoints MenuDisplayOperational
Page 58 and 59: XI. Repair PartsAll Solaris ® Seri
Page 60 and 61: 63159847311SIDE VIEW OFGAS VALVE102
Page 62 and 63: 12KeyNo.Manifold Orifice AssemblyDe
Page 64 and 65:
6 59738412Key No. Description Quant
Page 66 and 67:
SERVICE RECORDDateService Performed
Page 68:
LIMITED WARRANTYSubject to the term
show all

I&O Manual - Solaris Water Heaters - Categories On Thermal ...

Create successful ePaper yourself

Delete template?

Save as template?