DP, FP, HDP, FPK Display Panel Data Sheet - Trend

Data SheetDP, FP, HDP, FPKFIRMWARE (continued)ParametersA number of the item parameters which affect the display can bepre-set in the controller using the IQ controller configuration mode(e.g. item labels and units, knob node or module parameteradjustment, controller password protection, adjustment passwordlevel and range, language etc).Note that if some of an item type’s labels are set up (e.g somesensor labels), only those items of that type with preset labelswill be visible on the display panel, but if no labels of an item typeare set up, all items of that type can be seen.Password ProtectionIf a password has been set up in the controller then certain itemshave fixed password levels, whereas the password levels foradjustments can be defined by the user in the controller strategy.The password levels are shown below:Knobs0 to 100 (user-defined)Switches0 to 100 (user-defined)Addresses 90Time and Date 50Seasonal Time changes 50Zone times (current week) 30Zone times (standard week) 50Holiday date 50Holiday time 70Reprogram soft buttons 90When an attempt is made to change a protected parameter, theuser must enter a four digit PIN which has previously been set upin the controller to have a priority level above that for the selecteditem as shown above. If the PIN is valid, the change can be made,but if not valid, the change will be inhibited. Once a valid passwordis entered, it will enable changes for items equal to or below itspriority level. It will time-out two minutes after the last button ispressed.Programmable ButtonsThese buttons labelled A, B, C, D can be pre-programmed toselect particular items which are frequently monitored or changed(e.g setpoint adjustment, time control). A button is programmedby first selecting the required item, and then holding down therequired button for about 5 seconds. A PIN may be required forthe change to be made.LanguageThe language of the display panel may be changed by alteringthe display panel language selection in the controller configurationmode address module. This also changes the language of textalarm labels. The language may be selected from English,Spanish, Finnish, Swedish, Norwegian, Danish, German, Italian,Portuguese and French.DP, FP, HDP, FPK Display Panel Data Sheet TA102601 Issue 2/C 23/11/063

24VOKTX RX12345678910LAN16 17 18 19 2024V1 2 3 4 5 6 7 8 9 10 11 12 13 14 15TXLANRXLANABCDDP, FP, HDP, FPKData SheetHARDWAREDisplay Panel TypesThere are two basic types of current basic display panel, DP2and DP (sometimes referred to as 2DP), as well as the old typeof display panel. They all use LCD (liquid crystal) displays.DP2DPOld DP:This display panel uses membrane M1. It maybe mounted in the cover of an IQ2xx controller.It cannot be used outside a controller. It isidentified by a 34 way (IDC type) connector(normally connected by an attached ribbon cable).:This display panel uses membrane M1. It maybe mounted outside a IQ2xx controller (if thecontroller has an ‘RDS’, Remote Display Support,interface board fitted). It has a 25 way male ‘D’type connector fitted.:This display panel uses membrane M2. It hadvarious versions. The integral version had a 26Way IDC connector, whereas the external versionhad a 25 Way D type connector.These basic display panels may be fitted in the cover of an IQcontroller, fitted in the front of a panel, or provided as a hand heldunit which can be plugged into the controller.Integral Display PanelDisplay Panel in Front of PanelA display panel (DP) may be remotelymounted away from the controller,for example on a panel door. This isdone by using the front panelmounting kit (FPK).Alternatively the standard 600 x 600mm (23.6” x 23.6”) enclosure maybe purchased with the display panelalready fitted in the door (ENCLS/FP).gasketdisplay panel4 screwsDisplay panel fixed to doorusing fixing kit (FPK)Standard enclosure withdisplay panel fitted(ENCLS/FP)A 3 m (9’ 10.1”) cable is supplied withboth of these options.Note that a display panel may reducethe controller’s available 24 Vdcauxiliary output supply current by30 mAThe kit (FPK) provides 4 screws formounting on a panel door up to 5 mm(0.12”) thick; for a thicker door theinstaller should provide longer 4 mmscrews.ABCD16 17 18 19 20V1 2 3 4 5 6 7 8 9 10 11 12 13 14 15ABCDThe backplate may be used as a template to cut the holes in thepanel.Note that the display panel is not suitable for mounting outsidea building.IQ22x with integraldisplay panelIQ241/242 with integraldisplay panelIt can be used on an IQ22x, IQ23x, IQ241/242, or IQ250 controllerif it has been fitted with an ‘RDS’ interface. It can also be usedwith an IQ204 or any IQ1xx series controller except an IQ7x,IQ9x, IQ9x+, (although it may be used with an IQ9xe).An IQ22x, IQ23x, or IQ241/242 controller may be purchased withan integral display panel (DP2) fitted in the cover. The displaypanel thus requires no installation, and will operate when thecontroller is powered. The IQ22x, IQ23x, and IQ241/242controllers may also be retrofitted with a display panel bypurchasing the appropriate retrofit kit which includes a cable,and installation instructions and for the IQ22x and IQ23x, areplacement cover (fitted with a display panel), and for the IQ241/242, a display panel with nylon pillars for fitting into the cover.Note that a display panel may reduce the controller’s available24 Vdc auxiliary ouput supply current by 30 mA107mm (4.21”)58 mm (2.28”)39 mm(1.54”)33 mm(1.3”)55 mm (2.17”)35 mm(1.38”)15 mm(0.59”)5 holesØ 4.5 mm(0.18”)169 mm (6.65”)Backplate used as templateHand Held Display PanelThe display panel (DP) is also provided as a hand held unit(HDP). This allows the user to plug the display panel into acontroller either permanently or on a temporary basis. It is usefulas a portable tool for locally monitoring and adjusting a numberof controllers. A 1 m (39.37”) cable is supplied with the HDP.When plugging a display panel into a controller note that it mayreduce available 24 Vdc auxliary output supply current by 30 mA.It can be used on an IQ22x, IQ23x, IQ241/242, or IQ250 controllerif it has been fitted with an ‘RDS’ interface (ordered separately). Itcan also be used with an IQ204 or any IQ1xx series controller exceptan IQ7x, IQ9x, IQ9x+, (although it can be used with an IQ9xe).VConnection of hand helddisplay to IQ22x (if /RDSfitted)4 DP, FP, HDP, FPK Display Panel Data Sheet TA102601 Issue 2/C 23/11/06

Data SheetDP, FP, HDP, FPKHARDWARE (continued)Viewing Angle AdjustmentDuring installation the installer should check the viewing angle isappropriate for its use. It can be adjusted by turning a smallscrew located to the right of the display panel connector whenviewed from the rear.Adjustment ofviewing angleCOMPATIBILITYThe table below shows the compatibility between versions of display panels, and IQ controllers:SeriesIQ2xxIQ1xxControllersIntegralDisplay PanelM1/DP2M2Remote Display Panel(FP, FPK, HDP)M1/DPM2IQ21x IQ22x * *IQ23x * *IQ241/242 * *IQ246 IQ250 * *IQ251 IQ204 IQ7x IQ9x,10x9x+, IQ9xe,8xe ** IQ100+ IQ111, 111+,131, 131+,151, 151+ IQ104/OEM KeyM1: new membraneM1/DP2: new membrane with DP2 type displayM1/DP: new membrane with DP type displayM2: display panel with old membrane (obsolete)*: These controllers need to have the /RDS fitted to use a remotedisplay**: These controllers need a special 24 W to 24 W IDC adapter cableDP, FP, HDP, FPK Display Panel Data Sheet TA102601 Issue 2/C 23/11/065

Data SheetDP, FP, HDP, FPKDISPOSALCOSHH (Control of Substances Hazardous to Health - UKGovernment Regulations 2002) ASSESSMENT FOR DISPOSALOF DP,FP, HDP, FPK DISPLAY PANEL. No parts are affected.RECYCLING.All plastic and metal parts are recyclable. The printed circuitboard may be sent to any PCB recovery contractor to recoversome of the components for any metals such as gold and silver.WEEE Directive :At the end of their useful life the packagingand product should be disposed of using asuitable recycling centre.Do not dispose of with normal household waste.Do not burn.ORDER CODESNon USA Order Code USA Order CodeIQ2xx/DP/:IQ2xx (IQ22x, IQ23x, IQ241/242) controller with display panel in cover.882000130 :IQ221 controller with display panel in cover.882000150 :IQ222 controller with display panel in cover.882000170 :IQ223 controller with display panel in cover.882000210 :IQ229 controller with display panel in cover.KIT/DP2 Not available in USA :Kit for retro-fitting display panel into IQ241/242, complete with displaypanel, nylon pillars, attached ribbon cable, and installation instructions.COVER/DP2/IQ22x 882000220 :Kit for replacing cover of IQ22x with cover pre-fitted with display panelcomplete with attached ribbon cable and installation instructions.COVER/DP2/IQ23x Not available in USA :Kit for replacing cover of IQ23x with cover pre-fitted with display panelcomplete with attached ribbon cable and installation instructions.FPK Not available in USA :Kit for fitting display panel to the front of a panel complete with display panel,gasket, mounting screws, 3 m (9’ 10.1”) cable, and installation instructions.ENCLS/FP Not available in USA :600 x 600 x 210 mm (23.6” x 23.6” x 8.27”) cabinet pre-fitted with displaypanel complete with 3 m (9’ 10.1”) cable, mounting screws, and ENCLSinstallation instructions. The ENCLS cabinet is pre-drilled to fit a range of IQcontrollers.HDP Not available in USA :Hand held display panel complete with 1 m (39.37”) cable.Note that all the above display panel products are supplied with a display panel manual.KIT/2XX/RDS Not available in USA :Kit for fitting the remote display support (RDS) interface into an IQ2xxcontroller (IQ22x, IQ23x, IQ241/242, or IQ250) to enable a remote displaypanel (front of panel, or hand held) to be connected to the controller, completewith attached ribbon cable, mounting screws, and installation instructions.AccessoriesNon USA Order Code USA Order CodeCABLE/58-0935 Not available in USA :1 m (39.37”) length, 25 way ‘D’ type male to 25 way ‘D’ type female cablefor connecting display panel to controller.CABLE/58-0836 Not available in USA :3 m (9’ 10.1”) length, 25 way ‘D’ type male to 25 way ‘D’ type female cablefor connecting display panel to controller.DP, FP, HDP, FPK Display Panel Data Sheet TA102601 Issue 2/C 23/11/067

DP, FP, HDP, FPKData SheetSPECIFICATIONElectricalInput power :5 V (from IQ controller (resulting in 30mA from 24 Vdc input power)Cable distance :between display panel and controller,3 m (9’ 10.1”) max in an electricallynoise free environment. Screenedcable must be used.Display panel connectionDP, old DP :rear mounted 25 way D type male plug(hand-held, remotely mounted).DP2:rear mounted 34 Way IDC typeconnector (integrally mounted IQ2Series).old DP:rear mounted 26 way IDC typeconnector (integrally mounted IQ1Series - obsolete).DisplayNumber of characters :40 characters x 2 lines.Character format :5 x 7 dots.Display:LCD with LED backlight.MechanicalDimensions :190 x 144 x 32 mm (7.48” x 5.67” x 1.26”)(hand-held).Enclosure material :Front - ABS, back - PVC (hand-held).Weight:0.48 kg (1.06 lbs) (hand-held).EnvironmentalIP ratingHDP/DP/ENCLS/FPFPKULAmbient limitsHumidity:IP30.:IP of IQ to which it is fitted.:IP54.:membrane rated at IP54. Whenmounted in a panel, total rating dependson rating of panel.:(DP, FPK, KIT/2xx/RDS only) This unitis UL rated as ‘UL916, accessory to openenergy management equipment’.:0 to 50 °C (0 to 122°F).:0 to 90 %RH non condensing.Note that the display panel is not suitable for mountingoutside a building.Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois37,Switzerland by its Authorized Representative, Trend Control Systems Limited.Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereofwithout obligation to notify any person of such revisions or changes.Trend Control Systems LimitedP.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trend-controls.comTrend Control Systems USA6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.com8 DP, FP, HDP, FPK Display Panel Data Sheet TA102601 Issue 2/C 23/11/06