EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.9 VGA TestThe operation of the VGA is checked.(1) Select “9. VGA Test” from the main menu by pressing [9] and [ENTER] key.(2) When the following sub menu is displayed, select an item according to the display type of VGA or SVGA,in case of dual display model, primary display or secondary display.===== VGA Test Menu =====1. VGA 1st LCD Test2. VGA 2nd LCD Test3.SVGA 1st LCD Test4.SVGA 2nd LCD Test99. ENDINPUT NO.: _The VGA displays in 640 x 480 dots, and the SVGA does in 800 x 600 dots.(3) The red, green, blue and white bars are displayed. Pressing any key returns the display to the main menu.8-10
8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.10 COM SIO TestThe operation of COM and SIO ports of the ST-60 are checked.Before starting the test, connect a loop back connector to the port to be tested.(1) Select “10. COM SIO Test” from the Main Menu by pressing [1] [0], and the [ENTER] key.(2) When the following sub menu is displayed, select a port to be tested. When the selected port works properly,“[OK]” will be displayed. If there is any problem, “[NG]” will appear.Diagnostic Program===== COM Port Test Menu =====1:COM12:COM23:COM34:COM45:SIO16:SIO299:ENDNumber ==>[OK][OK][OK][OK][OK][OK](3) Pressing [9],[9], and the [ENTER] key will terminate this test and restore the display to the Main Menu.NOTES:1. The configuration of COM2 and SIO2 ports depends on whether or not the customer’s displayis used.CONNECTOR with Customer’s without Customer’sDisplayDisplayA COM 2 SIO 22. The loop back connector should be used at the time of this test performance.TXD + 1TXD - 2RXD + 3NC 4NC 5RXD - 6NC 7NC 88-11
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6:
1. UNPACKING EO18-12003(Revision Da
Page 7 and 8:
2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10:
3. MAIN UNIT REPLACEMENT EO18-12003
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
4. INSTALLATION PROCEDURE FOR OPTIO
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
5. ST-60 BIOS SETUP (A, B models) E
Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 95: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107: 10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

Create successful ePaper yourself

Delete template?

Save as template?