EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.2 LAN TestThe operation of the ST-60 Built-in LAN Card is checked.(1) Select “2. LAN Test” from the Main Menu by pressing [2] and the [ENTER] key.(2) First, detection of the card is performed.NOTE: In the middle of the detection, an error message “Can’t find installation control...” appears.Press the [ENTER] key to proceed.Scanning PCI...(3) Select “Test adapter” from the Main menu of the LAN Test, then press the [ENTER] key. When the Testadapter menu is displayed, select “Test adapter” by using arrow keys (↑, ↓) and press the [ENTER] key tostart the check.Main menuAutomatic setupView adapter configurationTest adapterInstall network driversView Help filesExit Setup(4) Confirm that all check results are “passed”. When the check is terminated, press the [ENTER] key to returnto “Test adapter” menu.Test adapterBus=1 Dev=08h Func=0 Addr=xxxxxxxxxxxx IRQ=xxNo responder.Diagnostic tests:Adapter tests passedOnboard loopback tests passedNetwork test passedThis adapter works properly.Press Enter to continue.(5) Pressing the [ESC] key twice changes the display to the screen as shown below. Select “Yes” by usingarrow keys (←, →) and press the [ENTER] key to terminate.Do you want to exit from setup now?Yes No Reboot now8-4
8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.3 BIOS Version TestThe operation of the ST-60 BIOS Version is checked.(1) Select “3. BIOS Version Test” from the Main Menu by pressing [3] and the [ENTER] key.(2) The ST-60 performs BIOS check. After that, [OK] or [NG] is displayed.•Single display modelMACHINE CHECK... [OK: ST-60N]•Dual display modelMACHINE CHECK... [OK: ST-60N Multimedia]Press any key to continue...(3) Pressing any key will terminate this test and restore the display to the Main Menu.8.4.4 Date & TimeThe operations of Date and Time are checked.(1) Select “4. DATE&TIME” from the Main Menu by pressing [4] and the [ENTER] key.(2) When “Date and Time” is displayed, pressing [0] or [9] key will terminate this test and restore the displayto the Main Menu.===== DATE & TIME =====date = 04/20/02time = 19:28:30Check OK? [OK:0 / NG:9]NOTE: When this test is terminated, the date and the time are not corrected automatically by pressing [9]which indicates the result is NG.8.4.5 Keyboard TestThe operation of the keyboard connected to the ST-60 is checked.(1) Select “5. Keyboard Test” from the Main Menu by pressing [5] and the [ENTER] key.(2) When the following sub menu is displayed, select the desired menu by entering the menu number (1 to 8).***** KEYBOARD TEST MENU *****1: KEYCLICK TEST (TEC 81 key)2: KEYCLICK TEST (TEC 132 Normal key)3: KEYCLICK TEST (TEC 132 Flat key)4: KEYCLICK TEST (TEC 78 key)5: KEYCLICK TEST (TEC 145 key)6: KEYCLICK TEST (TEC combi key)7: CONTROL KEY TEST8: CARD READ TEST99: EXITINPUT NO.:NOTE:Sub menus 4, 5, and 6 are required for the ST-4500 and ST-6400, therefore, these menus areunnecessary for the ST-60.8-5
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6:
1. UNPACKING EO18-12003(Revision Da
Page 7 and 8:
2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10:
3. MAIN UNIT REPLACEMENT EO18-12003
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
4. INSTALLATION PROCEDURE FOR OPTIO
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 89: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107: 10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

Create successful ePaper yourself

Delete template?

Save as template?