EO18-12003 - toshiba tec europe
EO18-12003 - toshiba tec europe EO18-12003 - toshiba tec europe
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE(2) Switch the display in order of “320 * 200 * 256”, “640 * 480 * 16”, and “720 * 400 * 16” by pressing [ENTER]key.(3) When the result of “720 * 400 * 16” is displayed, pressing [ENTER] key will return the display to the mainmenu.7.4.14 RS Scanner TestThe operation of the RS scanner is checked.(1) Select “RS Scanner Test” from the main menu by pressing [1] [4], and [ENTER] key.(2) When the following is displayed, set the COM port number and the type of the scanner, then press [F10] key(functioning as [Start] key).>COM Number (3:COM3, 6:SIO2)............[3]Type (1:HS-380, 2:LS-750, 3:LS-120)....[1]Command File Name......................[TSTSCNR.DAT][Quit] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [Start]NOTES:1. For setting, move the cursor to the parameter to be set by using the arrow keys (↓, ↑) or [ENTER]key, enter setting value, then press the [ENTER] key.2. This program runs according to the following settings.Baud rate: 9 6 0 0 bps7 bit/even/2 stopData transfer mode: Mode 4 (STX/ETX mode)NOTE:For HS-380, the above settings are the default options. For LS-700 and LS-750, the baud rate shouldbe set to 9600 bps.(3) The following message will be displayed. (The following code is example.)Master:F49012345678901F49012345678901OKCount OK = XX NG = 0(4) Pressing [F1] key will terminate this test and restore the display to the main menu.7.4.15 EndThe Diagnostic program is terminated.(1) Select “END” from the main menu by pressing [9], [9], and [ENTER] key. The diagnostic program will be terminatedand the DOS prompt will be displayed.7-16
8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.1 LIMITATION8. DIAGNOSTIC TEST OPERATION (C model)This chapter describes the Diagnostic test program provided to check for proper operation of the ST-60’s POS I/Odevices.8.1 LIMITATION(1) Since the system is not included in the Diagnostic Sheet due to a problem of the license, it is necessary to beinstalled on your site.For the installation procedure, refer to Section 8.3 SYSTEM FDK PREPARATION PROCEDURE.(2) The configuration file (CONFIG.SYS) in the Diagnostic Sheet is designed for MS-DOS Version 6.2.The installation of the system in the Diagnostic Sheet must be performed on the machine that MS-DOSVersion 6.2 has been properly installed.8.2 OUTLINEThe diagnostic test program checks the following POS I/O devices of the ST-60.• LAN• BIOS• Date/Time• Keyboard• PS-2 Mouse• USB Mouse• Speaker• VGA• COM, SIO port• LPT1• RJ Printer• Drawer• Memory• NV-RAM• UPS• FDD• HDD• Touch Panel• LIU• Sound• RS Scanner8-1
- Page 35 and 36: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 37 and 38: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
- Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
- Page 47 and 48: 5. ST-60 BIOS SETUP (A, B models) E
- Page 49 and 50: 5. ST-60 BIOS SETUP (A, B models) E
- Page 51 and 52: 5. ST-60 BIOS SETUP (A, B models) E
- Page 53 and 54: 5. ST-60 BIOS SETUP (A, B models) E
- Page 55 and 56: 5. ST-60 BIOS SETUP (A, B models) E
- Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 61 and 62: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 63 and 64: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 65 and 66: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 67 and 68: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 69 and 70: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 73 and 74: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 75 and 76: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 77 and 78: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 79 and 80: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 81 and 82: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 83 and 84: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 85: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 89 and 90: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 91 and 92: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 93 and 94: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 95 and 96: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 97 and 98: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 99 and 100: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 101 and 102: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 103 and 104: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 105 and 106: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 107: 10. PERIODICAL MAINTENANCE EO18-120
7. DIAGNOSTIC TEST OPERATION (A, B models) <strong>EO18</strong>-<strong>12003</strong>(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE(2) Switch the display in order of “320 * 200 * 256”, “640 * 480 * 16”, and “720 * 400 * 16” by pressing [ENTER]key.(3) When the result of “720 * 400 * 16” is displayed, pressing [ENTER] key will return the display to the mainmenu.7.4.14 RS Scanner TestThe operation of the RS scanner is checked.(1) Select “RS Scanner Test” from the main menu by pressing [1] [4], and [ENTER] key.(2) When the following is displayed, set the COM port number and the type of the scanner, then press [F10] key(functioning as [Start] key).>COM Number (3:COM3, 6:SIO2)............[3]Type (1:HS-380, 2:LS-750, 3:LS-120)....[1]Command File Name......................[TSTSCNR.DAT][Quit] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [Start]NOTES:1. For setting, move the cursor to the parameter to be set by using the arrow keys (↓, ↑) or [ENTER]key, enter setting value, then press the [ENTER] key.2. This program runs according to the following settings.Baud rate: 9 6 0 0 bps7 bit/even/2 stopData transfer mode: Mode 4 (STX/ETX mode)NOTE:For HS-380, the above settings are the default options. For LS-700 and LS-750, the baud rate shouldbe set to 9600 bps.(3) The following message will be displayed. (The following code is example.)Master:F49012345678901F49012345678901OKCount OK = XX NG = 0(4) Pressing [F1] key will terminate this test and restore the display to the main menu.7.4.15 EndThe Diagnostic program is terminated.(1) Select “END” from the main menu by pressing [9], [9], and [ENTER] key. The diagnostic program will be terminatedand the DOS prompt will be displayed.7-16