EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4.11 LAN EEPROM TestThe operation of the LAN EEPROM is checked.(1) Select “LAN EEPROM Test” from the main menu by pressing [1] [1], and [ENTER] key.(2) When the following is displayed, the message “Checksum OK” shows that the LAN EEPROM operatesproperly.Interactive PCnet-PCI II EEPROM Programmer V2.00Current EEPROM Contents Modified EEPROM ContentsChecksum OKNo Change0) Physical Address: 00 80 91 15 00 21 00 80 91 15 00 211) Hardware ID: 11 112) User Spcae 1: 1111 11113) Checksum 1: 0228 0228 (0228)4) BCR4: 00C0 00C05) BCR5: 00B0 00B06) BCR18: 9060 90607) BCR2: 0022 00228) BCR6: 4088 40889) BCR7: 0081 0081a) BCR9: 0000 0000b) Checksum 2: DD DD (DD)c) BCR22: FF06 FF06Show PCI Space Show Status Show EEPROM ImageProgram Load Default Setting QuitPress highlighted character to select an operation:NOTES:1. The displayed “0) Physical Address” shows MAC ADDRESS which is set for each product.2. The values of “3) Checksum 1” and “b) Checksum 2” depend on each product.(3) Pressing [q] key will terminate this test and restore the display to the main menu.NOTE: Do not make any test except for “Quit” because the LAN may operate improperly.7-12
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4.12 LAN Test (AMD)The operation of the LAN Controller is checked.NOTE:If the Plug & Play OS is set to [YES] at the BIOS setup, pressing [1] key may restore the display to the“ST-60 Diagnostic Test Program Main Menu”. In this case, select “” from the main menu by pressing [1][2], and [ENTER] key again.(1) Select “LAN Test” from the main menu by pressing [1] [2], and [ENTER] key.LAN Test (AMD) main menu* * * * * * * * * * * * * * * * * * * * * * * * * * * ** ** AMD PCnet(tm) Diagnostic Utility - v2.1 ** Copyright 1996-1997 Advanced Micro Devices, Inc. ** ** * * * * * * * * * * * * * * * * * * * * * * * * * * *Controller I/O Addr PCI Config Addr IRQ Controller Type1 OxFCEO 0x80002800 15 PCnet-PCI IIChoose a controller (q to quit):(2) Pressing [1] key displays the following sub menu.LAN Test (AMD) Sub menuCARD UNDER TESTI/O Addr PCI Config Addr IRQ Controller TypeOxFCEO 0x80002800 15 PCnet-PCI II1. Run Resources Tests2. Run Internal Loopback Tests3. Run External Loopback Tests (Loopback plug is required)4. Run Link Test as SENDER5. Run Link Test as RESPONDER6. Run All Tests7. Goto Main Menu8. Quit ApplicationEnter Highlighted character to Select a test:(3) Make each test by selecting [1] to [3] keys.NOTE:Do not perform the tests of “4. Run Link Test as SENDER”, “5. Run Link Test as RESPONDER”, and“6. Run ALL Tests” which the ST-60 does not support.7-13
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6:
1. UNPACKING EO18-12003(Revision Da
Page 7 and 8:
2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10:
3. MAIN UNIT REPLACEMENT EO18-12003
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
4. INSTALLATION PROCEDURE FOR OPTIO
Page 29 and 30:
4. INSTALLATION PROCEDURE FOR OPTIO
Page 31 and 32: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 81: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107: 10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

Create successful ePaper yourself

Delete template?

Save as template?