EO18-12003 - toshiba tec europe
EO18-12003 - toshiba tec europe EO18-12003 - toshiba tec europe
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4.9 RJ Printer TestThe operation of the printer (LPT1) is checked.(1) Select “RJ Printer Test” from the main menu by pressing [1], [1], and [ENTER] key.(2) When the following sub menu is displayed, select an RJ printer test item.RJ Printer Test Sub MenuDiagnostic ProgramRJ Printer Test Menu :RJ Type : Thermal1. All Print2. H Print3. Feed4. Full Cut5. Partial Cut6. Single Validation7. Multi Validation8. Multi Single Validation9. RJ Setup99. ENDNumber==>NOTE:When the TRST-53 thermal printer (partial cut type) is connected to LPT1, the following tests are notavailable.1. All Print5. Partial Cut6. Single Validation7. Multi Validation8. Multi Single Validation(3) Pressing [9], [9], and [ENTER] key while the RJ Printer Test Sub Menu is displayed will terminate this testand restore the display to the main menu.7.4.9.1 H Print(1) Select “H Print” from the sub menu by pressing [2] and [ENTER] key.(2) Hs are printed on a receipt.Double-sized letter H: 32 characters x 10 linesSingle-sized letter H: 64 characters x 10 lines7.4.9.2 Feed(1) Select “Feed” from the sub menu by pressing [3] and [ENTER] key.(2) The receipt is fed for 10 lines.7.4.9.3 Full Cut(1) Select “Full Cut” from the sub menu by pressing [4] and [ENTER] key.(2) The receipt is Fully cut (Full cut.)7-10
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4.9.4 RJ SetupPrinter type connected to LPT1 of the ST-60 is selected.(1) Select “RJ Setup” from the sub menu by pressing [9] and [ENTER] key.(2) When the following display appears, select the number corresponding to the connected printer’s specification,and then press the [ENTER] key.RJ Setup Sub MenuDiagnostic ProgramRJ SetupNo.11345RJ TypeThermalThermal_245 mm58 mmDRJST-50Colvmn048 064032 046024 000040 000033 000Print TypeSingleRJRJRJRJValidation000000055088077Input Number ==>NOTE:When the TRST-53 thermal printer is connected to LPT1 of the ST-60, be sure to select “1. Thermal”.(The default is “1. Thermal”.)(3) When the display shows “Are you sure? (Y/N)”, press the [Y] and [ENTER] keys to change the settings.NOTE:Since the changed settings are stored on the FDK, set the FDK to write enable state before starting theabove procedure.7.4.10 NV-RAM TestThe operation of the NV-RAM is checked.NOTE: Before starting this test, set the base address to D0000(H).(1) Select “NV-RAM Test” from the main menu by pressing [1] [0], and [ENTER] key.(2) The base address and the result of this test will be displayed.NV_RAM Check D000 [OK](3) Pressing [ESC] key will terminate this test and restore the display to the main menu.7-11
- Page 29 and 30: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 31 and 32: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 33 and 34: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 35 and 36: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 37 and 38: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
- Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
- Page 47 and 48: 5. ST-60 BIOS SETUP (A, B models) E
- Page 49 and 50: 5. ST-60 BIOS SETUP (A, B models) E
- Page 51 and 52: 5. ST-60 BIOS SETUP (A, B models) E
- Page 53 and 54: 5. ST-60 BIOS SETUP (A, B models) E
- Page 55 and 56: 5. ST-60 BIOS SETUP (A, B models) E
- Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 61 and 62: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 63 and 64: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 65 and 66: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 67 and 68: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 69 and 70: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 73 and 74: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 75 and 76: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 77 and 78: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 79: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 83 and 84: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 85 and 86: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 89 and 90: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 91 and 92: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 93 and 94: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 95 and 96: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 97 and 98: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 99 and 100: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 101 and 102: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 103 and 104: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 105 and 106: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 107: 10. PERIODICAL MAINTENANCE EO18-120
7. DIAGNOSTIC TEST OPERATION (A, B models) <strong>EO18</strong>-<strong>12003</strong>(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4.9.4 RJ SetupPrinter type connected to LPT1 of the ST-60 is selected.(1) Select “RJ Setup” from the sub menu by pressing [9] and [ENTER] key.(2) When the following display appears, select the number corresponding to the connected printer’s specification,and then press the [ENTER] key.RJ Setup Sub MenuDiagnostic ProgramRJ SetupNo.11345RJ TypeThermalThermal_245 mm58 mmDRJST-50Colvmn048 064032 046024 000040 000033 000Print TypeSingleRJRJRJRJValidation000000055088077Input Number ==>NOTE:When the TRST-53 thermal printer is connected to LPT1 of the ST-60, be sure to select “1. Thermal”.(The default is “1. Thermal”.)(3) When the display shows “Are you sure? (Y/N)”, press the [Y] and [ENTER] keys to change the settings.NOTE:Since the changed settings are stored on the FDK, set the FDK to write enable state before starting theabove procedure.7.4.10 NV-RAM TestThe operation of the NV-RAM is checked.NOTE: Before starting this test, set the base address to D0000(H).(1) Select “NV-RAM Test” from the main menu by pressing [1] [0], and [ENTER] key.(2) The base address and the result of this test will be displayed.NV_RAM Check D000 [OK](3) Pressing [ESC] key will terminate this test and restore the display to the main menu.7-11