EO18-12003 - toshiba tec europe
EO18-12003 - toshiba tec europe EO18-12003 - toshiba tec europe
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.3 SYSTEM FDK PREPARATION PROCEDURE(2) When the command prompt (C:\ >_) is displayed, set the diagnostic test program FDK to write enable state,insert it into FDD (drive A), and type “A:SETUP” and press the [ENTER] key.NOTE: Be sure to perform this operation on HDD (drive C), otherwise, the system FDK will not beprepared properly.C:\ >A:SETUP [ENTER](3) The system file stored on HDD (drive C) will be copied to the diagnostic test program FDK.C:\>A: SETUP [ENTER]C:\>ECHO OFFSystem transferred1 file(s) copied(4) The following message will appear when the setup is completed properly.Normal end!!C:\ >_(5) If an error occurs during this operation, the following message will appear.Setup error!!C:\ >_NOTE: If an error occurs, retry from step 2).7-2
7. DIAGNOSTIC TEST OPERATION (A, B models) EO18-12003(Revision Date: Jun. 21, 2002)7.4 DIAGNOSTIC TEST PROCEDURE7.4 DIAGNOSTIC TEST PROCEDUREInsert the prepared FDK including system file into the FDD of the ST-60. When turning the ST-60 power ON, theST-90’s diagnostic test program will start and the following main menu will be displayed.Selecting and following the displayed procedure will allow each POS I/O device’s operation check. To select themenu, enter the respective number. Pressing [9] twice will terminate the program.ST-60 Diagnostic Test Program Main MenuDiagnostic ProgramMain Menu :1. Speaker Test 13. VGA Test2. LPT1 Test 14. RS Scanner Test3. COM SIO Test 99. END4. UPS Test5. Drawer6. MCR Test7. Touch Pannel8. LIU Test9. RJ Printer Test10. NV RAM Test11. LAN EEPROM Test12. LAN Test (AMD)Number==>_7.4.1 Speaker TestThe operation of the ST-60 built-in speaker is checked.(1) Select “Speaker Test” from the main menu by pressing [1] and [ENTER] key.(2) When “Volume Check” is displayed, press any key of the keyboard. The ST-60's buil-in speaker will beep.(3) Pressing any key again will stop beeping and restore the display to the main menu.7.4.2 LPT1 TestThe connection of the printer (LPT1) is checked.(1) Select “LPT1 Test” from the main menu by pressing [2] and [ENTER] key.(2) The printer connected to LPT1 will print “LPT1 Test Print” on a receipt.7-3
- Page 21 and 22: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 23 and 24: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 25 and 26: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 27 and 28: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 29 and 30: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 31 and 32: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 33 and 34: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 35 and 36: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 37 and 38: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
- Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
- Page 47 and 48: 5. ST-60 BIOS SETUP (A, B models) E
- Page 49 and 50: 5. ST-60 BIOS SETUP (A, B models) E
- Page 51 and 52: 5. ST-60 BIOS SETUP (A, B models) E
- Page 53 and 54: 5. ST-60 BIOS SETUP (A, B models) E
- Page 55 and 56: 5. ST-60 BIOS SETUP (A, B models) E
- Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 61 and 62: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 63 and 64: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 65 and 66: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 67 and 68: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 69 and 70: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 71: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 75 and 76: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 77 and 78: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 79 and 80: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 81 and 82: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 83 and 84: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 85 and 86: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 89 and 90: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 91 and 92: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 93 and 94: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 95 and 96: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 97 and 98: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 99 and 100: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 101 and 102: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 103 and 104: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 105 and 106: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 107: 10. PERIODICAL MAINTENANCE EO18-120
7. DIAGNOSTIC TEST OPERATION (A, B models) <strong>EO18</strong>-<strong>12003</strong>(Revision Date: Jun. 21, 2002)7.3 SYSTEM FDK PREPARATION PROCEDURE(2) When the command prompt (C:\ >_) is displayed, set the diagnostic test program FDK to write enable state,insert it into FDD (drive A), and type “A:SETUP” and press the [ENTER] key.NOTE: Be sure to perform this operation on HDD (drive C), otherwise, the system FDK will not beprepared properly.C:\ >A:SETUP [ENTER](3) The system file stored on HDD (drive C) will be copied to the diagnostic test program FDK.C:\>A: SETUP [ENTER]C:\>ECHO OFFSystem transferred1 file(s) copied(4) The following message will appear when the setup is completed properly.Normal end!!C:\ >_(5) If an error occurs during this operation, the following message will appear.Setup error!!C:\ >_NOTE: If an error occurs, retry from step 2).7-2