EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

6. ST-60 BIOS SETUP (C model)EO18-12003(Revision Date: Dec. 23, 2002)6.3 PHOENIX SETUP SCREEN CONFIGURATION AND DEFAULT SETTING(5) PCI/PNP ISA IRQ MENUPhoenixBIOS SETUP UtilityAdvancedPCI/PNP ISA IRQ Resource ExclusionIRQ 3:[PnP]IRQ 4:[PnP]IRQ 5:[PnP]IRQ 7:[PnP]IRQ 9:[ISA]IRQ 10:[PnP]IRQ 11:[ISA]IRQ 15:[PnP]F1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Save and Exit(6) I/O device ConfigurationPhoenixBIOS SETUP UtilityAdvancedI/O Device ConfigurationCOM port 1:[Enabled]Base I/O Address[3F8]Interrupt [IRQ 4]COM port 2:[Enabled]Base I/O Address[2F8]Interrupt [IRQ 3]COM port 3:[Enabled]Base I/O Address[3E8]Interrupt [IRQ 11]COM port 4:[Enabled]Base I/O Address[2E8]Interrupt [IRQ 15]LPT port:[Enabled]Mode:[Bi-Directional]Base I/O Address [378]Interrupt [IRQ 7]( DMA channel [DMA 3] (displayed only in the ECP mode)Floppy Disk controller: [Enabled]Base I/O Address:[Primary]F1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Save and Exit(7) Advanced Chipset MenuPhoenixBIOS SETUP UtilityAdvancedAdvanced Chipset ControlVideo boot type [Onboard Video 1MB] *NOTEEnable Memory Gap:Enable D8 holeEnable CD hole[Disabled][Disabled][Enabled]Legacy USB Support [Disabled]USB #1 Controller[Enabled]PCI Reset[3S]COM4 info:[2E8h]ACPI Register[Enabled]F1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Save and ExitNOTE: For dual display model, [Disable Onboard Video] is shown as Video boot type.DO NOT CHANGE the “Video boot type” setting.6-7
6. ST-60 BIOS SETUP (C model)EO18-12003(Revision Date: Jul. 21, 2002)6.3 PHOENIX SETUP SCREEN CONFIGURATION AND DEFAULT SETTING6.3.3 Security MenuPhoenixBIOS SETUP UtilityMain Advanced Security Power Boot ExitSet User PasswordPassword on boot[Enter][Disabled]F1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Previous Value6.3.4 Power MenuPhoenixBIOS SETUP UtilityMain Advanced Security Power Boot ExitWake On LAN[Enabled]AC Power On[No Boot]Front Switch[Off]Init VGA First[Internal VGA]Backlight ON Timing [After VGA BIOS]Rear Backlight Default [On]F1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Previous Value6.3.5 Boot Menu(1) Boot MenuPhoenixBIOS SETUP UtilityMain Advanced Power Boot Exit+Removable Devices+Hard DriveCD-ROM DriveNetwork BootIntel(R) Boot Agent Version 3.0.046.3.6 Exit MenuPhoenixBIOS SETUP UtilityMain Advanced Security Power Boot ExitExit Saving ChangesExit Discarding ChangesLoad Setup Defaults(Compatible DOS/WinNT)Load Setup Defaults(Compatible Win98/Me)Load Setup Defaults(Compatible Win2000/XP)Load Setup Defaults(OpenPOS DOS/WinNT)Load Setup Defaults(OpenPOS Win98/Me)Load Setup Defaults(OpenPOS Win2000/XP)Discard ChangesSave ChangesF1 help ↑ , ↓ Select Item +/- Change Value F9 Setup DefaultsESC Exit ←,→Select Menu Enter Select > Sub-Menu F10 Save and Exit6-8
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6:
1. UNPACKING EO18-12003(Revision Da
Page 7 and 8:
2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10:
3. MAIN UNIT REPLACEMENT EO18-12003
Page 11 and 12: 3. MAIN UNIT REPLACEMENT EO18-12003
Page 27 and 28: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 61: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107: 10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?