EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

6. ST-60 BIOS SETUP (C model)EO18-12003(Revision Date: Jul. 21, 2002)6.1 GENERAL6. ST-60 BIOS SETUP (C model)6.1 GENERALTo change the setup programming procedure for the ROM-BIOS, press the [F2] key when the BIOS is started up(after completing the memory check).6.2 BASIC OPERATION AND KEYS USED6.2.1 How to Enter Phoenix SETUPPress the [F2] key immediately after displaying the memory capacity and the cache memory capacity at the systemstart up. The following is the display sample displayed at the system start up.PhoenixBIOS 4.0 Release 6.0Copyright 1995-1999 Phoenix Technologies Ltd.All Rights ReservedTEC PCBS11 #00x 02/xx/xx * See NOTE below.CPU = Intel(R) Celeron(TM) processor 566MHz640K System RAM Passed16K Removed For Memory HoleXXXM Extended RAM Passed0128K Cache SRAM PassedSystem BIOS ShadowedVideo BIOS ShadowedMouse initializedPress to enter SETUPNOTE: The default value differs depending on the model as shown below. For details, see Page 6-3.PCBS11: Single display modelPCBS12: Dual display model6.2.2 Tables of the Function KeysThe following are the keys usable on the BIOS setup screen and the respective functions.Alt-HDisplays outline and help.ESC, Alt-X Enters the preceding menu.↑, ↓ Moves the cursor.←, → Selects the menu item.+, F6, space Makes the value of the setup field go up.-, F5 Makes the value of the setup field go down.PgUp, PgDn Moves the cursor to the preceding page or the next page in the scrollable menu.Home/End Moves the cursor to the top row or the bottom row of the current menu.Enter Displays the option menu for the item indicated by “ “.F9Loads the setup default value. (In the current setup menu)F10Loads the setup value which has been previously set before entering the setup.(In the current setup menu)6-1
6. ST-60 BIOS SETUP (C model)EO18-12003(Revision Date: Jul. 21, 2002)6.2 BASIC OPERATION AND KEYS USED6.2.3 Menu Operation FlowThe following shows on how to enter the setup, change the setup menu, and exit from the setup.Press the [F2] key at the system start up.Main Menu[→][←][ESC], [Alt] + [X]Move the cursor to each item using the [↑] or [↓],then press the [Enter] key.Primary MasterPrimary SlaveKeyboard FeaturesAdvanced[→][←][ESC], [Alt] + [X]Move the cursor to each item using the [↑] or [↓],then press the [Enter] key.Cache MemoryPCI ConfigurationPCI Bus MasterPCI/PNP ISA IRQ Resource ExclusionI/O Device ConfigurationAdvanced Chipset ControlSecurity (Setting Password) *1[→][←][ESC], [Alt] + [X]Power[ESC], [Alt] + [X]Boot (Setting the Booting order) *2[→][←][ESC], [Alt] + [X]Move the cursor to each item using the [↑] or [↓],then press the [Enter] key.Removable DevicesHard DriveExit *3Exit Saving ChangesExit Discarding Changes6-2RebootMove the cursor to eachitem using the [↑] or [↓],then press the [Enter] key.
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6: 1. UNPACKING EO18-12003(Revision Da
Page 7 and 8: 2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10: 3. MAIN UNIT REPLACEMENT EO18-12003
Page 27 and 28: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
Page 55: 5. ST-60 BIOS SETUP (A, B models) E
Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107:
10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?