EO18-12003 - toshiba tec europe
EO18-12003 - toshiba tec europe EO18-12003 - toshiba tec europe
5. ST-60 BIOS SETUP (A, B models) EO18-120035.3 RESTRICTED ITEMS5.3 RESTRICTED ITEMSThe following are the restricted items for this BIOS (PCBS66) setup. If the setup is performed while ignoring thefollowing, the machine activity will not be guaranteed.1) How to restore the machine from the lock caused by setup failureAt the system start up, the machine may be locked while not entering to the setup due to the change of the setupof hardware basic activity timing such as the access timing to the memory. In this case, discharge the RTC(battery), start up the system by the default, then perform the setup again.NOTE:To discharge the battery, move the short pins 1 and 2 to pins 2 and 3 of SP54 on the TOUCH MAIN PCboard, and replace the short pin socket after about 5 seconds.2) Setting concerning the H/W timing, etc.Those items should not be changed. Especially, if the followings are changed, the machine activity will not beguaranteed.(1) Setting concerning the Cache Memory (Memory Cache)(2) Setting concerning the Chipset (Advanced Chipset Control)3) Help function of the setup is not provided, because it has been deleted due to theROM capacity.4) Note when the Plug & Play board is used in the OS which does not support the Plug& Play functionChange the setting as shown below when the activity is abnormal.Plug & Play OS[No]* Meaning of the above setting: If Yes, the address/interrupt, etc. will assigned to only VGA and HDD bythe Plug & Play function among the Plug & Play devices. As for the otherdevices except VGA and HDD, the management are left to the OS withnon-initialize status.(Recommended to the Windows95)If No, assign of the address/interrupt for the Plug & Play board connectedto the BIOS is performed as much as possible. In this case, the interruptassign described on the “PCI/PNP ISA IRQ Resource Exclusion” becomesthe effective function.5) In case that the warning message concerning the PCI board or Plug & Play board isdisplayed. (Conflict of the Plug & Play information, etc.)Perform the following setting to initialize the Plug & Play information, then start-up again.Reset Configuration Data [Yes]6) In case that the default values setting are performed by the F9 keyDefault values setting performed by the F9 key is effective only for one screen setting currently displayed.Therefore, when setting the default values, select Get Default Value in the Exit menu.7) In case that the board using the PCI Bus MasterWhen the board using the PCI Bus Master is used, set PCI Devices as shown below if the OS does not supportthe Plug & Play function.Enable Master[Enabled]5-13
5. ST-60 BIOS SETUP (A, B models) EO18-120035.3 RESTRICTED ITEMS8) Setting concerning the Power Relay and the UPSActivation and notice for the BIOS control of the Power Relay and the UPS are as follows.(1) To use this function, change the settings as shown below after completing the hardware installation.UPS[Enabled]Power Relay[Enabled](2) BIOS makes the relay/UPS ON/Enable according to the BIOS setup when turning the power ON.(3) Relay/UPS is turned OFF when the Windows95 is selected to “Shut down the computer?.” (OFF call ofAPM) To turn the power of the ST-5600 OFF by the OS other than the Windows95, the exclusive softwareis necessary.(4) If the power of the ST-60 is not turned OFF, reset the system by the Software Reset ([CTRL] + [ALT] +[DEL]) with the power switch provided at the front side turned OFF or by the Reset Switch provided at thefront side of the ST-60.9) In case that the power saving is used(1) Stop clock in the idle mode can not be set.(2) Even when Disable is set to the IRQ6 and IRQ14 on the Wake Up PM Events, the standby and thesuspend as the factor to cancel the idle mode will act corresponding to the setup value.(3) When using the APM, the setup of Idle, Standby, and Suspend should be designated to Disable.(Connecting or disconnecting the APM should be performed in FULL-ON mode.)(4) Even if Enabled is selected, the unit cannot be woke up by an IRQ during the suspend mode (save toRAM).5-14
- Page 3 and 4: TABLE OF CONTENTSEO18-12003(Revisio
- Page 5 and 6: 1. UNPACKING EO18-12003(Revision Da
- Page 7 and 8: 2. BEFORE INSTALLATION EO18-120032.
- Page 9 and 10: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 11 and 12: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 13 and 14: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 15 and 16: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 17 and 18: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 19 and 20: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 21 and 22: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 23 and 24: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 25 and 26: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 27 and 28: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 29 and 30: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 31 and 32: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 33 and 34: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 35 and 36: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 37 and 38: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
- Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
- Page 47 and 48: 5. ST-60 BIOS SETUP (A, B models) E
- Page 49 and 50: 5. ST-60 BIOS SETUP (A, B models) E
- Page 51 and 52: 5. ST-60 BIOS SETUP (A, B models) E
- Page 53: 5. ST-60 BIOS SETUP (A, B models) E
- Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 61 and 62: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 63 and 64: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 65 and 66: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 67 and 68: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 69 and 70: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 73 and 74: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 75 and 76: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 77 and 78: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 79 and 80: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 81 and 82: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 83 and 84: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 85 and 86: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 89 and 90: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 91 and 92: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 93 and 94: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 95 and 96: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 97 and 98: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 99 and 100: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 101 and 102: 8. DIAGNOSTIC TEST OPERATION (C mod
- Page 103 and 104: 8. DIAGNOSTIC TEST OPERATION (C mod
5. ST-60 BIOS SETUP (A, B models) <strong>EO18</strong>-<strong>12003</strong>5.3 RESTRICTED ITEMS8) Setting concerning the Power Relay and the UPSActivation and notice for the BIOS control of the Power Relay and the UPS are as follows.(1) To use this function, change the settings as shown below after completing the hardware installation.UPS[Enabled]Power Relay[Enabled](2) BIOS makes the relay/UPS ON/Enable according to the BIOS setup when turning the power ON.(3) Relay/UPS is turned OFF when the Windows95 is selected to “Shut down the computer?.” (OFF call ofAPM) To turn the power of the ST-5600 OFF by the OS other than the Windows95, the exclusive softwareis necessary.(4) If the power of the ST-60 is not turned OFF, reset the system by the Software Reset ([CTRL] + [ALT] +[DEL]) with the power switch provided at the front side turned OFF or by the Reset Switch provided at thefront side of the ST-60.9) In case that the power saving is used(1) Stop clock in the idle mode can not be set.(2) Even when Disable is set to the IRQ6 and IRQ14 on the Wake Up PM Events, the standby and thesuspend as the factor to cancel the idle mode will act corresponding to the setup value.(3) When using the APM, the setup of Idle, Standby, and Suspend should be designated to Disable.(Connecting or disconnecting the APM should be performed in FULL-ON mode.)(4) Even if Enabled is selected, the unit cannot be woke up by an IRQ during the suspend mode (save toRAM).5-14