EO18-12003 - toshiba tec europe
EO18-12003 - toshiba tec europe EO18-12003 - toshiba tec europe
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12003(Revision Date: Mar. 16, 2007)4.8 INSTALLING THE NV-RAM (NVMST-50-32/128-QM)4) Make sure that the DIP switch setting is as shown below. If it is not as shown below, set the DIP switch to ONposition.ON ON5) Remove the top cover. (Refer to Section 3.2.1)1OFF6) Lead the MCR/HOST cable in the holes A and B. (Refer to Fig.4-18)Connector (6 pin)MCR/HOST CableFIU Tilt StayTop CoverFig. 4-18Hole A Hole B7) Remove the short sockets from the short pins SP19 and SP55 on the TOUCH MAIN PC Board or SP1 and SP2on the ST-PGA ENGINE PC Board. (For the location of the short sockets, refer to Section 4.9.1)MCR/HOST CableCN7 (9 pin)TOUCH MAINPC Board4-7Fig. 4-198) Connect the cables removed in STEP 5) in order of the BIU cable, Touch LVDS cable, and earth plate. Andthen, connect the MCR/HOST cable to CN7 on the TOUCH MAIN PC Board or CN2 on the ST-PGA ENGINEPC Board (Refer to Fig.4-19). Make sure that the hooks of the bottom cover (back, right and left sides) engagethe top cover, and reassemble the top cover.9) Reassemble the FIU top cover ass’y. (Refer to Section 3.1.1)NOTE: Before lowering the FIU top cover ass’y, also connect the MCR/HOST cable to CN2 on theTOUCH MCRCNT PC board.10) Connect the PC keyboard and FDD, install the Diag. FDK into the FDD, and turn the ST-60 power ON. Then,make the speaker, MCR, and LIU tests. (For diagnostic test operation, refer to Section 6.)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12003(Revision Date: Mar. 16, 2007)4.9 SHORT PIN AND DIP SWITCH SETTING4.8 INSTALLING THE NV-RAM (NVMST-50-32/128-QM)On the TOUCH MAIN PC Board or ST-PGA ENGINE PC Board, a 32-pin socket for inserting the NV-RAM is installed.To insert the NV-RAM, note that IC the Socket number of pins of IC varies according IC Socket to RAM capacity as follows.1PIN1 321PINNV-SRAMNV-SRAM28PIN (32KB)32PIN (128KB)NOTE:When the NV-RAM is installed, jumper setting is required.For the jumper setting, refer to Section 4.9 SHORT PIN AND DIP SWITCH SETTING.4-8
- Page 1 and 2: TEC POS TerminalST-60 SERIESMainten
- Page 3 and 4: TABLE OF CONTENTSEO18-12003(Revisio
- Page 5 and 6: 1. UNPACKING EO18-12003(Revision Da
- Page 7 and 8: 2. BEFORE INSTALLATION EO18-120032.
- Page 9 and 10: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 11 and 12: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 13 and 14: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 15 and 16: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 17 and 18: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 19 and 20: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 21 and 22: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 23 and 24: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 25 and 26: 3. MAIN UNIT REPLACEMENT EO18-12003
- Page 27 and 28: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 29 and 30: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 31: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 35 and 36: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 37 and 38: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 39 and 40: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 41 and 42: 4. INSTALLATION PROCEDURE FOR OPTIO
- Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
- Page 45 and 46: 5. ST-60 BIOS SETUP (A, B models) E
- Page 47 and 48: 5. ST-60 BIOS SETUP (A, B models) E
- Page 49 and 50: 5. ST-60 BIOS SETUP (A, B models) E
- Page 51 and 52: 5. ST-60 BIOS SETUP (A, B models) E
- Page 53 and 54: 5. ST-60 BIOS SETUP (A, B models) E
- Page 55 and 56: 5. ST-60 BIOS SETUP (A, B models) E
- Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 59 and 60: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 61 and 62: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 63 and 64: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 65 and 66: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 67 and 68: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 69 and 70: 6. ST-60 BIOS SETUP (C model)EO18-1
- Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 73 and 74: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 75 and 76: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 77 and 78: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 79 and 80: 7. DIAGNOSTIC TEST OPERATION (A, B
- Page 81 and 82: 7. DIAGNOSTIC TEST OPERATION (A, B
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT <strong>EO18</strong>-<strong>12003</strong>(Revision Date: Mar. 16, 2007)4.9 SHORT PIN AND DIP SWITCH SETTING4.8 INSTALLING THE NV-RAM (NVMST-50-32/128-QM)On the TOUCH MAIN PC Board or ST-PGA ENGINE PC Board, a 32-pin socket for inserting the NV-RAM is installed.To insert the NV-RAM, note that IC the Socket number of pins of IC varies according IC Socket to RAM capacity as follows.1PIN1 321PINNV-SRAMNV-SRAM28PIN (32KB)32PIN (128KB)NOTE:When the NV-RAM is installed, jumper setting is required.For the jumper setting, refer to Section 4.9 SHORT PIN AND DIP SWITCH SETTING.4-8