EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.22 RS Scanner TestThe operation of the RS scanner is checked.(1) Select “22. RS Scanner Test” from the Main Menu by pressing [2] [2], and the [ENTER] key.(2) When the following is displayed, set the COM port number and the type of the scanner, then press [F10] key(functioning as [Start] key).>COM Number (3:COM3, 6:SIO2)............[3]Type (1:HS-380, 2:LS-750, 3:LS-120)....[1]Command File Name......................[TSTSCNR.DAT][Quit] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [Start]NOTES: 1. For setting, move the cursor to the parameter to be set by using the arrow keys ([≤] and [¯])or [ENTER] key, enter setting value, then press the [ENTER] key.2. This program runs according to the following settings.Baud rate: 9600 bps7 bit/even/2 stopData transfer mode: Mode 4 (STX/ETX mode)NOTE:For HS-380, the above settings are the default options. For LS-700 and LS-750, the baud rateshould be set to 9600 bps.(3) The following message will be displayed. (The following code is example.)Master:F49012345678901F49012345678901OKCount OK = XX NG = 0(4) Pressing the [F1] key will terminate this test and restore the display to the Main Menu.8-18
8. DIAGNOSTIC TEST OPERATION (C model)EO18-12003(Revision Date: Jun. 21, 2002)8.4 DIAGNOSTIC OPERATION METHOD8.4.23 Sound TestThe operation of the on-board Sound controller is checked.Before performing the Touch Panel Test, slide the write protection tab of the FDK to the write enable side.(1) Select “23. Sound Test” from the Main Menu by pressing [2] [3], and the [ENTER] key.(2) The following is displayed. As following the instruction on the display, terminate this diag, insert the DiagFDK (2/2) into the FDD, and press [0] and the [ENTER] key together.End This TestSelect 99(End DIAG)Insert DIAG 2/2 FDKInput “0” + Enter(3) When the following is sub menu is displayed, select “1.SOUND Test” by pressing [1] and the [ENTER]key.Diagnostic Program===== Main Menu: =====1.SOUND Test99.ENDINPUT NO.:_(4) The sound test is performed. When working correctly, the speaker sounds. After this test is completed, thescreen restores to the Sound Test menu as shown below.===== SOUND Test Menu: =====1.TEST START99.END(5) Pressing [9] [9], and the [ENTER] key will terminate this test and restore the display to the sub menu.Additionally, pressing [9] [9], and the [ENTER] key will restore the display to the Main Menu.8.4.24 EndThe Diagnostic program is terminated.Select “END” from the Main Menu by pressing [9], [9], and the [ENTER] key. The diagnostic program will be terminatedand the DOS prompt will be displayed.8-19
Page 1 and 2:
TEC POS TerminalST-60 SERIESMainten
Page 3 and 4:
TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6:
1. UNPACKING EO18-12003(Revision Da
Page 7 and 8:
2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10:
3. MAIN UNIT REPLACEMENT EO18-12003
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
4. INSTALLATION PROCEDURE FOR OPTIO
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
5. ST-60 BIOS SETUP (A, B models) E
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54: 5. ST-60 BIOS SETUP (A, B models) E
Page 55 and 56: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 87 and 88: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 103: 8. DIAGNOSTIC TEST OPERATION (C mod
Page 107: 10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?