Gaskleen® Sealed-In-Line Filter Assembly - Pall Corporation (PLL)

Gas Filtration Assemblies — PTFEData Sheet A93aGaskleen ® Sealed-in-LineFilter AssemblyDescriptionThe Gaskleen ® Sealed-in-Line filterassembly is specifically designed for≥ 3 nanometer (0.003 µm) filtration ofprocesses with flow rates up to200 scfm.• 316L stainless steel electropolishedhousing• Emflon ® or Emflon PF elementavailable• High temperature and pressurecapabilities• 100% integrity tested• Cleanroom manufactured andpackaged• 100% helium leak tested• CE marked in accordance withPED 97/23/ECSpecificationsMaterials• Electropolished 316L stainless steelhousing• ≤ 0.64 µm / 25 µin or ≤0.25 µm R a /10 µin internal surface finish• Housing material meets or exceedsVIM/VAR specificationsElement Options• Emflon medium: PTFECore, cage, and end caps:PolypropyleneO-ring: Teflon 1 encapsulated Viton 1• Emflon PF medium: PTFECore, cage, and end caps: PFA 440HPO-ring: Teflon encapsulated VitonRemoval Rating• ≥ 3 nmConnections• 1 in Butt weld (1.65 mm / 0.065 in wall)• 1 1 ⁄2 in Butt weld (1.65 mm / 0.065 inwall)Preconditioned Cleanliness• < 1.0 ppm moisture contribution• < 0.5 ppm THC contributionOperating Conditions• Maximum operating pressure:1.89 MPa / 275 psig• Maximum operating temperature:Emflon element 80°C / 176°FEmflon PF element 121°C / 250°F• Maximum forward differential pressure:0.55 MPa @ 50°C / 80 psid @ 120°F;0.35 MPa @ 80°C / 50 psid @ 176°F• Maximum reverse differential pressure:0.34 MPa @ 21°C / 50 psid @ 70°FLeak Rating• 100% helium leak tested to10 -6 atm • cm 3 /s• Design tested to 2 x 10 -8 atm •cm 3 /sPackaging• Double baggedOuter bag: aluminized mylarInner bag: polyethylene•N 2 purged1Teflon and Viton are trademarks ofE. I. du Pont de Nemours and Company

Pressure Drop vs. Gas Flow RateClean Pressure Drop (psid)32.521.510.5000.21 MPa / 30 psigInlet0.21 MPa / 30 psigInletNitrogen Flow Rate (scfm) 20˚C / 68˚F0.21 MPa / 30 psigInlet0.69 MPa /100 psig Inlet20 40 60 80 100 12020151050Clean Pressure Drop (kPa)Clean Pressure Drop (psid)3.532.521.510.5000.21 MPa /30 psig Inlet50 100 150 200 250Nitrogen Flow Rate (scfm) 20˚C / 68˚F0.69 MPa /100 psig Inlet0.21 MPa /30 psig Inlet0.69 MPa /100 psig Inlet20151050Clean Pressure Drop (kPa)SILPF1112BW16 (0.21 MPa / 30 psig)SIL1101BW16 (0.21 MPa / 30 psig & 0.69 MPa / 100 psig)SIL1112BW24 (0.21 MPa / 30 psig & 0.69 MPa / 100 psig)SIL1212BW16 (0.21 MPa / 30 psig & 0.69 MPa / 100 psig)SIL1212BW24 (0.21 MPa / 30 psig & 0.69 MPa / 100 psig)Dimensions102 mm4 inLPart Numbers / Ordering InformationPart Number Description Length (L) Preconditioned(mm / in)SIL1101BW16 Emflon element 1 in butt weld 25 µin / 0.64 µm R a 573.8 / 22.59 NoSIL1112BW24 Emflon element 1 1 ⁄2 in butt weld 10 µin / 0.25 µm R a 572.0 / 22.52 YesSILPF1112BW16 Emflon PF element 1 in butt weld 10 µin / 0.25 µm R a 573.8 / 22.59 YesSILPF1111BW24 Emflon PF element 1 1 ⁄2 in butt weld 25 µin / 0.64 µm R a 572.0 / 22.52 YesSIL1212BW16 Emflon element 1 in butt weld 10 µin / 0.25 µm R a 829.3 / 32.65 YesSIL1212BW24 Emflon element 1 1 ⁄2 in butt weld 10 µin / 0.25 µm R a 827.5 / 32.58 YesSILPF1212BW16 Emflon PF element 1 in butt weld 10 µin / 0.25 µm R a 829.3 / 32.65 YesSILPF1212BW24 Emflon PF element 1 1 ⁄2 in butt weld 10 µin / 0.25 µm R a 827.5 / 32.58 YesUnit conversion: 1 bar = 100 kilopascals25 Harbor Park DrivePort Washington, New York 110501.800.360.7255 toll free (only in US)1.516.484.3600 phone1.516.625.3610 faxmicroelectronics@pall.comVisit us on the Web at www.pall.com/microPall Corporation has offices and plants throughout the world.© Copyright 2008, Pall Corporation. Pall, , Gaskleen, and Emflon are trademarks of Pall Corporation. ® Indicates aPall trademark registered in the USA.is a service mark of Pall Corporation.A93a 1/08