Dresser Roots Model 5 Prover Manual - The Meter and Valve ...

More documents

Recommendations

Info

2 Year WarrantyDresser Roots Meters & Instruments (herein referred to as the Company) agrees to supply equipment ofgood design and first class material and workmanship. In the event of any defect of material or workmanship,the Company will repair F.O.B. place of manufacture, or furnish without charge, place of manufacture, similarpart or parts which, within one year after their shipment, are proven to have been so defective at the time ofshipment, provided the Purchaser gives the Company immediate written notice of suchalleged defects.Notwithstanding the proceeding, warranty claims involving Model 5 ROOTS Prover(s) used only to provemeter volume accuracy, may be made within two (2) years from shipment. A complete list of productscovered by this extended warranty is available by writing our general offices.Except as herein provided, there are no other warranties, either expressed or implied (including withoutlimitation the implied warranties of merchantability and fitness for particular purpose), and any suchwarranties are hereby expressly disclaimed. The Company, except in the case of gross or willful negligence,shall not be liable for any damages for cause or reason whatsoever, either direct, indirect, special orconsequential, arising out of any contract or from the operation or failure properly to operate any apparatusor equipment sold. No allowance will be made for repairs or alterations unless made with the written consentfirst obtained from the Company. Neither shall the Company be held liable or in any way responsible for workdone, apparatus furnished, or repairs made by others. Auxiliary equipment supplied hereunder not manufacturedby the Company and so identified by the Company is subject to the warranty of the manufacturerthereof and the Purchaser’s recourse shall be limited to such other warranty.For additional information, consult your Yellow Pages under Meters - Dresser ROOTS Gas Meters, or contactour general offices at:Dresser Roots Meters & InstrumentsDresser, Inc.P. O. Box 42176Houston, Texas 77242-2176Phone: 832-590-2303Fax: 832-590-2494Dresser UK, Ltd.Dresser HouseGillibrands RoadEast Gillibrands EstateSkelmersdale, Lancashire WN8 9TUPhone: 44-(0)-1695-52600Fax: 44-(0)-1695-52610Dresser Industrial Products, B.V.Industrieterrein 4NL-5981 NK PanningenThe NetherlandsPhone: +31 (0)-77-306-6040Fax: +31 (0)-77-307-649453
Roots Meters & InstrumentsDresser, Inc.16240 Port Northwest DriveHouston, Texas 77041-2645 USAInside US Ph: 800.521.1114 Fax: 800.335.5224Outside US Ph: 832.590.2303 Fax: 832.590.2494©2004,2008 Dresser, Inc.ROOTS, and DRESSER are registered trademarks of Dresser, Inc.Windows is a registered trademark of Microsoft Corporation.LabVIEW is a trademark of National Instruments Corporation.www.dresser.comRPO_510.08
Page 1 and 2:
MODEL 5 PROVER & SOFTWARE MANUALRoo
Page 3 and 4:
6. Equipment Setup ................
Page 5 and 6: 1.3 Component ListThe following is
Page 7 and 8: Master MeterJunction Box(s)Controll
Page 9 and 10: • CAUTION: Purge all Field Meters
Page 11 and 12: 2. Installing the Model 5 Prover So
Page 13 and 14: 3. The Startup Screen and Help3.1 T
Page 15 and 16: 13. High Limit: This configurable P
Page 17 and 18: Table 1. Drive Rates for TEST CONTR
Page 19 and 20: 5.5 Test VolumeRefer to Configuring
Page 21 and 22: 6. Equipment SetupImportant: Before
Page 23 and 24: 10. Attach one end of the blue inpu
Page 25 and 26: . Plug the Optical Scanner cable in
Page 27 and 28: 7. Running a Meter Test7.1 Selectin
Page 29 and 30: 9. CONTROLLER DIGITIZER ERROR - Thi
Page 31 and 32: 7. Master Meter Temp. - the tempera
Page 33 and 34: In the Show Report box, scroll thro
Page 35 and 36: Figure 11The Prover Calibration Scr
Page 37 and 38: 9.5 How to Calibrate the Master Met
Page 39 and 40: 4. Type in the reference temperatur
Page 41 and 42: All Provers except 2M/10M: Allow ti
Page 43 and 44: 10.5 Meter PurgeSelect “Meter Pur
Page 45 and 46: Unplug the extension cord from the
Page 47 and 48: 5. Accuracy is out of specification
Page 49 and 50: 11.3 Assistance & Service Procedure
Page 51 and 52: AppendixB. TC Unit Operational Chec
Page 53 and 54: Testing Continuously Compensated me
Page 55: Spare Part ListDescription Part Num
show all

Dresser Roots Model 5 Prover Manual - The Meter and Valve ...

Create successful ePaper yourself

Delete template?

Save as template?