Murano Wardrobe instructions - Mamas & Papas
Murano Wardrobe instructions - Mamas & Papas Murano Wardrobe instructions - Mamas & Papas
Murano Wardrobe V1 30/11/04 15:08 Page 8STEP 9Turn the carcass over sothat the back edge ofboth of the side panelsface upwards.The back edges of thepanels have a recess tofit the back panels, seediagram.Slot the right side panel(2) onto the base paneland the two bottomrails, see diagram.Tighten the cams in theunderside of the basepanel and the bottomrails by inserting a flatheadscrewdriver intothe slots in the tops ofthe cams. Turn the camsclockwise until they aretight.2Screw four cam studs(D) into the outer holesalong the edge of thetop panel (5) using across-head screwdriver,see diagram.Attach the door stop (G)to the front edge of thetop panel by aligning theslots in the back of theplate with the pilot holesin the front edge of thetop panel.Screw two screws (H)through the slots in thedoor stop and into thepilot holes in the toppanel using a cross-headscrewdriver.5STEP 10DGH- 8 -
Murano Wardrobe V1 30/11/04 15:08 Page 9STEP 11Insert four cams (F) intothe large holes in thetops of the side panels.Ensure that the arrowson the heads of thecams face the top of theside panels, seediagram.Slot the top panel (5)onto the two sidepanels, ensure that thegroove in the back edgeof the top panel isaligned with the recessin the side panels.Tighten the cams in thetops of the side panelsby inserting a flat-headscrewdriver into theslots in the tops of thecams. Turn the camsclockwise until they aretight.F5STEP 12Before fixing the backpanels to the wardrobeyou will need to checkthat it is square.To do this, measure fromthe bottom corner ofone side panel to the topcorner of the opposite(A to A), see diagram.Now measure theopposite diagonal (B toB), if the measurementsare unequal then thewardrobe is not square.To square the wardrobe,gently push the topcorner of the longestdiagonal towards theshortest top corner andre-measure, continueuntil equal (a 2-3mmdifference is acceptable).- 9 -
- Page 1 and 2: Murano Wardrobe V1 30/11/04 15:08 P
- Page 3: Murano Wardrobe V1 30/11/04 15:08 P
- Page 6 and 7: Murano Wardrobe V1 30/11/04 15:08 P
- Page 10 and 11: Murano Wardrobe V1 30/11/04 15:08 P
- Page 12 and 13: Murano Wardrobe V1 30/11/04 15:08 P
- Page 14 and 15: Murano Wardrobe V1 30/11/04 15:08 P
- Page 16: Murano Wardrobe V1 30/11/04 15:08 P
<strong>Murano</strong> <strong>Wardrobe</strong> V1 30/11/04 15:08 Page 9STEP 11Insert four cams (F) intothe large holes in thetops of the side panels.Ensure that the arrowson the heads of thecams face the top of theside panels, seediagram.Slot the top panel (5)onto the two sidepanels, ensure that thegroove in the back edgeof the top panel isaligned with the recessin the side panels.Tighten the cams in thetops of the side panelsby inserting a flat-headscrewdriver into theslots in the tops of thecams. Turn the camsclockwise until they aretight.F5STEP 12Before fixing the backpanels to the wardrobeyou will need to checkthat it is square.To do this, measure fromthe bottom corner ofone side panel to the topcorner of the opposite(A to A), see diagram.Now measure theopposite diagonal (B toB), if the measurementsare unequal then thewardrobe is not square.To square the wardrobe,gently push the topcorner of the longestdiagonal towards theshortest top corner andre-measure, continueuntil equal (a 2-3mmdifference is acceptable).- 9 -
Change language