ToneLab Owner's Manual - Vox
ToneLab Owner's Manual - Vox ToneLab Owner's Manual - Vox
TroubleshootingIf you suspect a malfunction, please check the following points first. If this doesnot resolve the problem, contact a nearby dealer.1. The amp isn’t powering up when the STANDBY switch is“on”• Is the AC/AC power supply connected to the rear panel ~AC9V jack?• Is the AC/AC power supply plugged into an AC outlet?• Is the STANDBY switched on?• Could the AC/AC power supply be damaged?2. There’s no sound• Is your guitar turned up?• Are both ends of your guitar cable plugged into the correct jacks?• Is your guitar cable working?• Could the rear panel OUTPUT LEVEL knob be turned down?• Using the ORIGINAL VALUE LED, check the settings of the GAIN, TREBLE,MIDDLE, BASS, VR VOLUME and CH VOLUME (on certain AMP TYPES, if theEQ controls are all turned down, there will be little or no sound coming from theamp due to the way the circuit of the original works). And, if a PEDAL is beingused, check the DRIVE and LEVEL settings.• Are you in MANUAL MODE? If yes, turn the following controls above their minimumsetting: PEDAL DRIVE & PEDAL LEVEL [3], GAIN, TREBLE, MIDDLE,BASS, VR GAIN & CH VOLUME.• Could you have activated Mute on a connected foot controller? Defeat the Mutefunction.3. There’s no sound from the OUTPUT or PHONES jacks whenyou use them.• Check that the LEVEL knob that adjusts their output isn’t turned all the waydown.4. No signal (or a distorted signal) is heard from the DIGITALOUT jack.• Could the GLOBAL “DOUT LVL” be set to a low or excessively high value?52
5. You can’t hear any MODULATION, DELAY or REVERB effectseven though they’re dialed in...• Are the effect LEDs lit?If an LED is dark, the corresponding effect is off. Press the TYPE button toselect an effect type.• Could the modulation “DEPTH” or the delay/reverb “MIX” be set to a low value?Press the TYPE button to select an effect and use the value knobs to adjust theappropriate parameters.• Could the effect be bypassed? Is the effect type LED blinking?If so, press the TAP button to cancel bypass. The effect type LED will stop blinkingand remain lit.6. You’re using the ACOUSTIC pedal effect and getting nastyhigh frequency distortion.• Could the Drive setting be excessively high?• Are you using a very high output humbucking pickup?Either turn down the volume of your guitar, or turn down the GAIN setting.7. The sound connected to your guitar amp is distorted, orsounds wrong.• Could the AMP/LINE switch be set to “LINE”?• Could LEVEL be raised excessively?ProgramListTunerFootControllerSpec.TroubleshootingFactorysettingsMIDI/DIGITAL53
- Page 11 and 12: IntroductionWELCOME ABOARD!Many tha
- Page 13 and 14: Apart from the vitalvalve tone this
- Page 15 and 16: A Guitarist’s Guided Panel TourHe
- Page 17 and 18: 2 EFFECTS SECTIONThe PEDAL effects
- Page 19: NR SENS: Noise reduction (p.19)****
- Page 22 and 23: SetupNOTE: You MUST turn off the po
- Page 24: USING ToneLab FOR LIVE PERFORMANCEE
- Page 27 and 28: Creating and Storing Your OwnProgra
- Page 29 and 30: ADJUSTING THE NOISE REDUCTION (UTIL
- Page 31 and 32: Explanations of the Amp andEffect T
- Page 33 and 34: Tube TalkUs Brits call ‘em valves
- Page 35 and 36: 3. AC30As already stated, the VOX A
- Page 37 and 38: 7. UK ’80SThis is modelled on a 1
- Page 39 and 40: ups. It is also incredibly responsi
- Page 41 and 42: B. CABINET MODELSNow let’s look a
- Page 43 and 44: 11. OFFOK, this not a cabinet. The
- Page 45 and 46: 3. ACOUSTICWanna go “unplugged”
- Page 47 and 48: D. MOD (Modulation) EFFECTSThis sec
- Page 49 and 50: 1. OFFSelect this if you don’t wa
- Page 51 and 52: TunerFor your convenience, ToneLab
- Page 53 and 54: 1. Press the UTILITY button (3.4) t
- Page 55 and 56: Control via MIDIMIDI stands for Mus
- Page 57 and 58: 2. Press the 1/PREV or 2/NEXT butto
- Page 59 and 60: BACKING UP1. Connect ToneLab’s MI
- Page 61: Restoring the Factory PresetProgram
- Page 65 and 66: ProgramChange Variable RangeSystem
- Page 67 and 68: Program list1-1 BLIZZARDAMP CABINET
- Page 69 and 70: 5-1 DIRTAMP CABINET TREBLE MIDDLE B
- Page 71 and 72: 9-1 OLDGUYAMP CABINET TREBLE MIDDLE
- Page 73 and 74: IndexSymbols16Numerics1OCTAVE 362OC
- Page 75 and 76: Program SheetThis sheet is for you
TroubleshootingIf you suspect a malfunction, please check the following points first. If this doesnot resolve the problem, contact a nearby dealer.1. The amp isn’t powering up when the STANDBY switch is“on”• Is the AC/AC power supply connected to the rear panel ~AC9V jack?• Is the AC/AC power supply plugged into an AC outlet?• Is the STANDBY switched on?• Could the AC/AC power supply be damaged?2. There’s no sound• Is your guitar turned up?• Are both ends of your guitar cable plugged into the correct jacks?• Is your guitar cable working?• Could the rear panel OUTPUT LEVEL knob be turned down?• Using the ORIGINAL VALUE LED, check the settings of the GAIN, TREBLE,MIDDLE, BASS, VR VOLUME and CH VOLUME (on certain AMP TYPES, if theEQ controls are all turned down, there will be little or no sound coming from theamp due to the way the circuit of the original works). And, if a PEDAL is beingused, check the DRIVE and LEVEL settings.• Are you in MANUAL MODE? If yes, turn the following controls above their minimumsetting: PEDAL DRIVE & PEDAL LEVEL [3], GAIN, TREBLE, MIDDLE,BASS, VR GAIN & CH VOLUME.• Could you have activated Mute on a connected foot controller? Defeat the Mutefunction.3. There’s no sound from the OUTPUT or PHONES jacks whenyou use them.• Check that the LEVEL knob that adjusts their output isn’t turned all the waydown.4. No signal (or a distorted signal) is heard from the DIGITALOUT jack.• Could the GLOBAL “DOUT LVL” be set to a low or excessively high value?52